Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation ECU sub-assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E224430E09
2.771,0.552 2.99,0.802 0.219,0.25 10 false 5 2.729,0.74 3.021,0.969 0.292,0.229 10 false z3 3.781,0.563 4.052,0.781 0.271,0.219 10 false 13 3.771,0.74 4.146,1 0.375,0.26 10 false I28 3.188,0.604 3.604,0.885 0.417,0.281 10 false IL+2 2.771,1.313 2.938,1.51 0.167,0.198 10 false 3 2.729,1.49 3.01,1.698 0.281,0.208 10 false z3 3.781,1.313 4.052,1.542 0.271,0.229 10 false 11 3.781,1.49 4.104,1.719 0.323,0.229 10 false I28 3.208,1.354 3.604,1.615 0.396,0.26 10 false -DP 2.802,1.865 3.708,2.26 0.906,0.396 10 false Spiral Cable Sub-assembly 0.885,1.104 1.083,1.25 0.198,0.146 10 false LH 0.885,1.865 1.24,2.01 0.354,0.146 10 false RH 0.406,2.49 2.469,3.042 2.063,0.552 10 false Steering Pad Switch Assembly 0.438,3.479 1.313,3.917 0.875,0.438 10 false from Battery 2.563,4.156 3.031,4.49 0.469,0.333 10 false TAIL 3.427,3.604 4.021,3.865 0.594,0.26 10 false PANEL 4.448,3.813 5.677,4.469 1.229,0.656 10 false to Main Body ECU (Multi-plex Network Body ECU) 6.01,0.76 6.344,0.979 0.333,0.219 10 false ILL+ 5.74,0.635 6,0.844 0.26,0.208 10 false 10 5.875,4.448 6.25,4.688 0.375,0.24 10 false I64 5.875,4.604 6.865,5.01 0.99,0.406 10 false Navigation ECU Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation ECU sub-assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation ECU sub-assembly. B
No illumination comes on (navigation ECU sub-assembly, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I28-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the steering pad switch assembly connector (for 3 Spoke).

E245199C02
2.635,0.802 2.979,1.031 0.344,0.229 3.74,0.854 4.042,1.094 false 3.51,0.833 3.281,0.375 false 0.167,0.219 0.625,0.625 0.458,0.406 10 false *a 4.083,1.063 4.375,1.208 0.292,0.146 10 false IL+2 3.135,0.219 3.396,0.365 0.26,0.146 10 false -DP 2.75,0.823 3.063,1.021 0.313,0.198 10 false z3 0.354,0.219 0.948,0.563 0.594,0.344 10 false (*A)
*A for 3 Spoke - -
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



b.

Disconnect the steering pad switch assembly connector (for 4 Spoke).

E224423C04
4.198,1.271 4.573,1.5 0.375,0.229 4.521,0.844 4.823,1.083 false 4.313,0.833 4.052,0.365 false 0.229,0.229 0.792,0.719 0.563,0.49 10 false *a (*A) 4.792,1.115 5.427,1.542 0.635,0.427 10 false IL+2 3.896,0.167 4.344,0.448 0.448,0.281 10 false -DP 4.323,1.302 4.646,1.469 0.323,0.167 10 false z3
*A for 4 Spoke - -
*a Component without harness connected
(Steering Pad Switch Assembly)
- -



c.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.


d.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.



e.

Proceed to the next step based on the check result.


Result:
Result Proceed to
OK A
NG (for 3 Spoke) B
NG (for 4 Spoke) C



A

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

B

REPLACE STEERING PAD SWITCH ASSEMBLY (for 3 Spoke)

C

REPLACE STEERING PAD SWITCH ASSEMBLY (for 4 Spoke)

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.
E263757C02
1.333,0.5 1.667,0.75 0.333,0.25 0.417,3.75 0.75,4 0.333,0.25 1.74,1.083 1.99,0.604 false 2.427,1.083 2.25,0.604 false 1.083,4.25 1.281,3.771 false 1.625,4.25 1.521,3.771 false 0.135,0.135 0.448,0.333 0.313,0.198 10 *a 1.177,0.229 1.49,0.427 0.313,0.198 10 *b 1.583,1.094 1.896,1.292 0.313,0.198 10 IL+2 2.385,1.094 2.698,1.292 0.313,0.198 10 -DP 1.438,0.542 1.75,0.74 0.313,0.198 10 z3 0.281,3.552 0.594,3.75 0.313,0.198 10 *c 1.552,4.271 1.938,4.469 0.385,0.198 10 IL+2 0.958,4.271 1.271,4.469 0.313,0.198 10 -DP 0.51,3.792 0.823,3.99 0.313,0.198 10 I28
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z3-3 (-DP) - I28-11 (-DP) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z3-5 (IL+2) - I28-13 (IL+2) Always Below 3 Ω
z3-3 (-DP) - I28-11 (-DP) Always Below 3 Ω


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



HINT:



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I64-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR