| GPS mark is not displayed.
|
Proceed to "GPS Mark is not Displayed"
|
|
| Navigation antenna assembly
|
|
| Navigation ECU sub-assembly
|
|
| Date and time on navigation screen is different from actual date and time.
|
Proceed to "GPS Mark is not Displayed"
|
|
| Navigation antenna assembly
|
|
| Navigation ECU sub-assembly
|
|
| Vehicle position mark deviates from correct position and does not return to correct position.
|
Proceed to "GPS Mark is not Displayed"
|
|
| Navigation antenna assembly
|
|
| Navigation ECU sub-assembly
|
|
| Cursor or map rotates when vehicle is stopped.
|
Proceed to "Cursor or Map Rotates when Vehicle Stopped"
|
|
| Navigation ECU sub-assembly
|
|
| Vehicle position mark moves in the opposite direction to the vehicle.
|
Proceed to "Cursor or Map Rotates when Vehicle Stopped"
|
|
| Proceed to "Reverse Signal Circuit"
|
|
| Navigation ECU sub-assembly
|
|
| Vehicle position mark deviates from and returns to correct position repeatedly even though GPS mark is displayed.
|
Proceed to "GPS Mark is not Displayed"
|
|
| Drive the vehicle for sensor learning. (At a place where GPS signals can be received, drive the vehicle clockwise and counterclockwise in at least a 200 meter square 2 times or more.)
|
-
|
| Navigation antenna assembly
|
|
| Navigation ECU sub-assembly
|
|
| Vehicle position mark moves slow or fast.
|
Proceed to "GPS Mark is not Displayed"
|
|
| Navigation antenna assembly
|
|
| Navigation ECU sub-assembly
|
|
| Voice guidance does not function.
|
Proceed to "Voice Guidance does not Function"
|
|
| Proceed to "Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier"*1
|
|
| Proceed to "Speaker Circuit"
|
|
| Proceed to "Navigation Voice Circuit"*1
|
|
| Stereo component amplifier assembly*1
|
|
| Navigation ECU sub-assembly
|
|
| Map display is incomplete.
|
Hard disk drive
|
|
| Navigation ECU sub-assembly
|
|
| Route cannot be calculated.
|
Proceed to "Route cannot be Calculated"
|
|
| Navigation ECU sub-assembly
|
|
| Navigation ECU cannot record memory point registration or each item setting.
|
Hard disk drive
|
|
| Navigation ECU sub-assembly
|
|
| A message indicating to wait for a while because of low temperature is displayed.
|
Start the engine and increase cabin temperature near navigation ECU sub-assembly.
|
-
|
| Hard disk drive
|
|
| Navigation ECU sub-assembly
|
|
| A message is displayed because map data cannot be read, and current position screen is not displayed.
|
If message appears only when driving on rough roads, check if message disappears when vehicle is stopped.
|
-
|
| Hard disk drive
|
|
| Navigation ECU sub-assembly
|
|
| Map screen turns white or blue. (GPS receiving status is displayed normally, and switches and own vehicle position mark are also displayed normally.)
|
Change map scale to smallest. (a scale that shows a large area.)
|
-
|
| Hard disk drive
|
|
| Navigation ECU sub-assembly
|
|
| Customizable parameters cannot be changed. (Customizable parameters can be changed by using the intelligent tester.)
|
Navigation ECU sub-assembly
|
|
| The password set using the memory point export/import function has been forgotten.
|
Proceed to "Clear Backup Password of Export/Import Memory Point Function" in Operation Check
|
|
| Reverse signal does not change in vehicle signal check mode.
|
Proceed to "Reverse Signal Circuit"
|
|
| Navigation ECU sub-assembly
|
|
| Parking brake switch signal does not change in vehicle signal check mode.
|
Proceed to "Parking Brake Switch Circuit"
|
|
| Navigation ECU sub-assembly
|
|