Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E226159E10
0.406,2.141 2.819,2.316 2.413,0.175 10 Stereo Component Amplifier Assembly 4.646,1.952 4.997,2.099 0.351,0.147 10 I67 4.646,2.141 6.617,2.309 1.971,0.168 10 Navigation ECU Sub-assembly 5.113,1.485 5.492,1.632 0.379,0.147 10 TX1- 5.113,0.672 5.533,0.847 0.42,0.175 10 TX1+ 4.894,1.392 5.005,1.539 0.111,0.147 10 8 4.894,0.579 4.999,0.754 0.105,0.175 10 7 1.81,1.504 2.056,1.651 0.246,0.147 10 TX- 1.775,0.691 2.055,0.866 0.28,0.175 10 TX+ 2.19,1.387 2.369,1.534 0.179,0.147 10 7 2.171,0.574 2.369,0.749 0.198,0.175 10 8 0.406,1.952 0.756,2.099 0.351,0.147 10 I69

CAUTION / NOTICE / HINT

HINT:

The navigation ECU sub-assembly is the master unit.


PROCEDURE

1.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.
E221758C06
1.483,0.394 1.971,0.686 0.487,0.292 1.611,0.445 1.893,0.627 0.282,0.182 10 I67 0.133,0.086 0.304,0.261 0.17,0.175 10 *a 1.365,1.73 1.657,1.203 false 2.086,1.73 1.794,1.203 false 1.15,1.749 1.476,1.924 0.325,0.175 10 TX1- 1.895,1.749 2.251,1.924 0.355,0.175 10 TX1+
*a Component without harness connected
(Navigation ECU Sub-assembly)


Disconnect the navigation ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-7 (TX1+) - I67-8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-8 (TX+) - I67-7 (TX1+) Always Below 1 Ω
I69-7 (TX-) - I67-8 (TX1-) Always Below 1 Ω
I69-8 (TX+) - Body ground Always 10 kΩ or higher
I69-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG