Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the navigation ECU sub-assembly.

WIRING DIAGRAM

E226165E72
1.021,0.75 1.958,1.104 0.938,0.354 10 false from Battery 0.375,1.563 2.01,1.885 1.635,0.323 10 false from ACC NO. 1 Relay 0.469,2.375 2.083,2.708 1.615,0.333 10 false from IG1 NO. 2 Relay 3.385,1.031 4.063,1.292 0.677,0.26 10 false RADIO-B 3.365,1.823 4.063,2 0.698,0.177 10 false ECU-ACC 3.198,2.615 4.271,2.813 1.073,0.198 10 false ECU-IG1 NO. 2 5.531,2.979 5.74,3.156 0.208,0.177 10 false 7 5.521,1.396 5.719,1.563 0.198,0.167 10 false 3 5.479,0.792 5.792,1.052 0.313,0.26 10 false I64 5.479,1.583 5.906,1.865 0.427,0.281 10 false I64 5.479,2.375 5.948,2.667 0.469,0.292 10 false I67 5.479,3.156 5.854,3.417 0.375,0.26 10 false I64 5.813,0.719 6.104,0.885 0.292,0.167 10 false +B1 5.813,1.521 6.25,1.688 0.438,0.167 10 false ACC1 5.813,2.385 5.99,2.552 0.177,0.167 10 false IG 5.813,3.167 6.25,3.333 0.438,0.167 10 false GND1 5.521,0.615 5.646,0.781 0.125,0.167 10 false 4 5.521,2.188 5.646,2.354 0.125,0.167 10 false 1 5.677,3.615 6.688,4 1.01,0.385 10 false Navigation ECU Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY, BODY GROUND)
a.

Disconnect the navigation ECU sub-assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I64-4 (+B1) - I64-7 (GND1) Always 11 to 14 V
I64-3 (ACC1) - I64-7 (GND1) Ignition switch ACC 11 to 14 V
I67-1 (IG) - I64-7 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR