Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2030EQ _58 Vehicle Interior _014670 SEAT _0077330 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2650 Slide Sensor Malfunction The forward and backward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Slide motor (separate type front seat cushion spring assembly)

·

Wire harness or connector



WIRING DIAGRAM

for LHD


B342629
2.26,1.073 2.417,1.271 0.156,0.198 10 false 4 2.25,1.583 2.406,1.781 0.156,0.198 10 false 1 2.26,2.073 2.417,2.271 0.156,0.198 10 false 2 2.26,2.583 2.417,2.781 0.156,0.198 10 false 3 1.344,3.063 1.927,3.313 0.583,0.25 10 false e8 1.354,3.219 3.188,3.417 1.833,0.198 10 false Slide Motor 0.99,3.833 2.615,4.271 1.625,0.438 10 false Separate Type Front Seat Cushion Spring Assembly 4.917,3.854 6.479,4.469 1.563,0.615 10 false Position Control ECU and Switch Assembly 4.823,1.177 5.406,1.427 0.583,0.25 10 false e11 4.823,1.688 5.406,1.938 0.583,0.25 10 false e11 4.823,2.188 5.406,2.438 0.583,0.25 10 false e12 5.156,1.177 5.74,1.427 0.583,0.25 10 false SLD+ 4.813,2.698 5.396,2.948 0.583,0.25 10 false e12 5.156,1.677 5.74,1.927 0.583,0.25 10 false SLD- 5.156,2.208 5.74,2.458 0.583,0.25 10 false SSRS 5.156,2.708 5.74,2.958 0.583,0.25 10 false SGND 4.885,1 5.125,1.229 0.24,0.229 10 false 3 4.896,1.5 5.135,1.729 0.24,0.229 10 false 4 4.885,2.01 5.042,2.208 0.156,0.198 10 false 5 4.875,2.51 5.031,2.708 0.156,0.198 10 false 1


for RHD


B260685
2.237,1.046 2.485,1.204 0.248,0.158 10 4 2.237,1.553 2.474,1.711 0.237,0.158 10 1 2.237,2.057 2.344,2.215 0.107,0.158 10 2 2.237,2.57 2.344,2.727 0.107,0.158 10 3 5.164,1.16 5.559,1.316 0.394,0.156 10 SLD+ 5.164,1.664 5.524,1.826 0.36,0.162 10 SLD- 5.164,2.171 5.606,2.33 0.442,0.159 10 SSRS 5.164,2.677 5.599,2.834 0.435,0.156 10 SGND 4.891,0.985 4.998,1.142 0.107,0.158 10 3 4.891,1.491 4.998,1.649 0.107,0.158 10 4 4.891,1.995 4.998,2.153 0.107,0.158 10 5 4.891,2.508 4.998,2.666 0.107,0.158 10 1 1.343,3.028 1.577,3.198 0.235,0.17 10 d8 1.343,3.203 2.08,3.361 0.737,0.158 10 Slide Motor 1.045,3.8 2.692,4.148 1.647,0.348 10 Separate Type Front Seat Cushion Spring Assembly 4.993,3.8 6.395,4.128 1.402,0.327 10 Position Control ECU and Switch Assembly 4.823,1.158 5.103,1.311 0.28,0.153 10 d11 4.823,1.668 5.103,1.821 0.28,0.153 10 d11 4.823,2.172 5.103,2.325 0.28,0.153 10 d12 4.823,2.683 5.103,2.835 0.28,0.153 10 d12


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDE MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

5.INSPECT SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)
a.

Disconnect the e8*1 or d8*2 slide motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e8-2 - e8-3 Slide switch on 4.8 to 5.1 V

for RHD
Tester Connection Condition Specified Condition
d8-2 - d8-3 Slide switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
3.CHECK SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238515
0.99,0.438 1.385,0.656 0.396,0.219 1.938,0.438 2.333,0.656 0.396,0.219 0.135,0.135 0.646,0.594 0.51,0.458 10 false *a 1.125,0.458 1.448,0.688 0.323,0.229 10 false e8 2.073,0.469 2.396,0.698 0.323,0.229 10 false d8 1.458,0.458 1.781,0.688 0.323,0.229 10 false *A 2.417,0.458 2.74,0.688 0.323,0.229 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(Slide Motor (Separate Type Front Seat Cushion Spring Assembly))


Reconnect the e8*1 or d8*2 slide motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e8-2 - Body ground Slide switch on 4.5 to 4.8 V

for RHD
Tester Connection Condition Specified Condition
d8-2 - Body ground Slide switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
a.

Disconnect the e12*1 or d12*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e12-5 (SSRS) - e8-2 Always Below 1 Ω
e12-1 (SGND) - e8-3 Always Below 1 Ω
e12-5 (SSRS) - Body ground Always 10 kΩ or higher
e12-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d12-5 (SSRS) - d8-2 Always Below 1 Ω
d12-1 (SGND) - d8-3 Always Below 1 Ω
d12-5 (SSRS) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238256
0.104,0.052 0.271,0.219 0.167,0.167 10 *a
*a Component without harness connected
(Slide Motor (Separate Type Front Seat Cushion Spring Assembly))


Disconnect the e8*1 or d8*2 slide motor connector.

*1: for LHD

*2: for RHD



b.

Check if the seat cushion spring moves smoothly when the battery is connected to the slide motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seat cushion spring moves forward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seat cushion spring moves backward



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)

NG

REPLACE SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
a.

Disconnect the e11*1 or d11*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e11-3 (SLD+) - e8-4 Always Below 1 Ω
e11-4 (SLD-) - e8-1 Always Below 1 Ω
e11-3 (SLD+) - Body ground Always 10 kΩ or higher
e11-4 (SLD-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d11-3 (SLD+) - d8-4 Always Below 1 Ω
d11-4 (SLD-) - d8-1 Always Below 1 Ω
d11-3 (SLD+) - Body ground Always 10 kΩ or higher
d11-4 (SLD-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR