Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2030EQ _58 Vehicle Interior _014670 SEAT _0077330 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2651 Reclining Sensor Malfunction The forward and backward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Reclining motor (front seatback frame sub-assembly (for Driver))

·

Wire harness or connector



WIRING DIAGRAM

for LHD


B342629
2.26,1.073 2.417,1.271 0.156,0.198 10 false 4 2.25,1.583 2.406,1.781 0.156,0.198 10 false 1 2.26,2.073 2.417,2.271 0.156,0.198 10 false 2 2.26,2.583 2.417,2.781 0.156,0.198 10 false 3 1.344,3.063 1.927,3.313 0.583,0.25 10 false g3 1.354,3.219 3.188,3.417 1.833,0.198 10 false Reclining Motor 0.729,3.813 3.021,4.323 2.292,0.51 10 false Front Seatback Frame Sub-assembly (for Driver) 4.917,3.854 6.479,4.469 1.563,0.615 10 false Position Control ECU and Switch Assembly 4.823,1.177 5.406,1.427 0.583,0.25 10 false e11 4.823,1.688 5.406,1.938 0.583,0.25 10 false e11 4.823,2.188 5.406,2.438 0.583,0.25 10 false e12 5.156,1.177 5.74,1.427 0.583,0.25 10 false RCL+ 4.813,2.698 5.396,2.948 0.583,0.25 10 false e12 5.156,1.677 5.74,1.927 0.583,0.25 10 false RCL- 5.156,2.208 5.74,2.458 0.583,0.25 10 false SSRR 5.156,2.708 5.74,2.958 0.583,0.25 10 false SGND 4.875,1 5.115,1.229 0.24,0.229 10 false 9 4.844,1.5 5.25,1.802 0.406,0.302 10 false 11 4.854,2.01 5.198,2.323 0.344,0.313 10 false 11 4.875,2.51 5.031,2.708 0.156,0.198 10 false 1


for RHD


B348529
0.865,3.833 2.552,4.344 1.688,0.51 10 false Front Seatback Frame Sub-assembly (for Driver) 1.302,3.083 1.615,3.281 0.313,0.198 10 false f3 1.292,3.24 2.438,3.469 1.146,0.229 10 false Reclining Motor 2.25,1.573 2.406,1.771 0.156,0.198 10 false 1 2.26,1.083 2.417,1.281 0.156,0.198 10 false 4 2.26,2.063 2.417,2.26 0.156,0.198 10 false 2 2.25,2.583 2.406,2.781 0.156,0.198 10 false 3 4.813,1.177 5.271,1.375 0.458,0.198 10 false d11 4.823,1.677 5.281,1.875 0.458,0.198 10 false d11 4.813,2.188 5.271,2.385 0.458,0.198 10 false d12 4.813,2.688 5.271,2.885 0.458,0.198 10 false d12 4.896,1 5.146,1.198 0.25,0.198 10 false 9 4.854,2.021 5.104,2.219 0.25,0.198 10 false 11 4.885,2.521 5.135,2.719 0.25,0.198 10 false 1 4.854,1.521 5.104,1.719 0.25,0.198 10 false 11 5.135,1.698 5.75,1.896 0.615,0.198 10 false RCL- 5.135,1.188 5.75,1.385 0.615,0.198 10 false RCL+ 5.125,2.208 5.74,2.406 0.615,0.198 10 false SSRR 5.125,2.719 5.74,2.917 0.615,0.198 10 false SGND 4.854,3.844 6.448,4.302 1.594,0.458 10 false Position Control ECU and Switch Assembly


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RECLINING MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

5.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER))
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.

Disconnect the g3*1 or f3*2 reclining motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
g3-2 - g3-3 Reclining switch on 4.8 to 5.1 V

for RHD
Tester Connection Condition Specified Condition
f3-2 - f3-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER)))

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
3.CHECK RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER)))
a.
B238515
0.781,0.469 1.146,0.698 0.365,0.229 2.26,0.469 2.625,0.698 0.365,0.229 0.125,0.052 0.302,0.219 0.177,0.167 10 false *a 0.896,0.49 1.344,0.823 0.448,0.333 10 false g3 2.406,0.5 2.698,0.792 0.292,0.292 10 false f3 1.219,0.469 1.667,0.802 0.448,0.333 10 false *A 2.688,0.479 3.135,0.813 0.448,0.333 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(Reclining Motor (Front Seatback Frame Sub-assembly (for Driver)))


Reconnect the g3*1 or f3*2 reclining motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
g3-2 - Body ground Reclining switch on 4.5 to 4.8 V

for RHD
Tester Connection Condition Specified Condition
f3-2 - Body ground Reclining switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER)))

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the e12*1 or d12*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e12-11 (SSRR) - g3-2 Always Below 1 Ω
e12-1 (SGND) - g3-3 Always Below 1 Ω
e12-11 (SSRR) - Body ground Always 10 kΩ or higher
e12-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d12-11 (SSRR) - f3-2 Always Below 1 Ω
d12-1 (SGND) - f3-3 Always Below 1 Ω
d12-11 (SSRR) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU & SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER))
a.
B238256
0.107,0.047 0.272,0.21 0.165,0.162 10 *a
*a Component without harness connected
(Reclining Motor (Front Seatback Frame Sub-assembly (for Driver)))


Disconnect the g3*1 or f3*2 reclining motor connector.

*1: for LHD

*2: for RHD



b.

Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seatback moves forward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seatback moves backward



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER))

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the e11*1 or d11*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e11-9 (RCL+) - g3-4 Always Below 1 Ω
e11-11 (RCL-) - g3-1 Always Below 1 Ω
e11-9 (RCL+) - Body ground Always 10 kΩ or higher
e11-11 (RCL-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d11-9 (RCL+) - f3-4 Always Below 1 Ω
d11-11 (RCL-) - f3-1 Always Below 1 Ω
d11-9 (RCL+) - Body ground Always 10 kΩ or higher
d11-11 (RCL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR