Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2030EQ _58 Vehicle Interior _014670 SEAT _0077330 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2652 Front Vertical Sensor Malfunction The upward and downward lock detection position of the sensor the same.
·

Position control ECU and switch assembly

·

Front vertical motor (separate type front seat cushion spring assembly)

·

Wire harness or connector



WIRING DIAGRAM

for LHD


B348529
0.813,3.823 2.927,4.208 2.115,0.385 10 false Separate Type Front Seat Cushion Spring Assembly 1.177,3.052 1.49,3.25 0.313,0.198 10 false e9 1.177,3.208 2.729,3.448 1.552,0.24 10 false Front Vertical Motor 2.25,1.573 2.406,1.771 0.156,0.198 10 false 1 2.26,1.083 2.417,1.281 0.156,0.198 10 false 4 2.26,2.063 2.417,2.26 0.156,0.198 10 false 2 2.25,2.583 2.406,2.781 0.156,0.198 10 false 3 4.813,1.177 5.271,1.375 0.458,0.198 10 false e11 4.823,1.677 5.281,1.875 0.458,0.198 10 false e11 4.813,2.188 5.271,2.385 0.458,0.198 10 false e12 4.813,2.688 5.271,2.885 0.458,0.198 10 false e12 4.896,1 5.146,1.198 0.25,0.198 10 false 8 4.896,2.021 5.146,2.219 0.25,0.198 10 false 3 4.885,2.521 5.135,2.719 0.25,0.198 10 false 1 4.896,1.521 5.146,1.719 0.25,0.198 10 false 5 5.135,1.698 5.75,1.896 0.615,0.198 10 false FRV- 5.135,1.188 5.75,1.385 0.615,0.198 10 false FRV+ 5.125,2.208 5.74,2.406 0.615,0.198 10 false SSFV 5.125,2.719 5.74,2.917 0.615,0.198 10 false SGND 4.854,3.844 6.448,4.302 1.594,0.458 10 false Position Control ECU and Switch Assembly


for RHD


B348529
0.813,3.823 2.927,4.208 2.115,0.385 10 false Separate Type Front Seat Cushion Spring Assembly 1.177,3.052 1.49,3.25 0.313,0.198 10 false d9 1.177,3.208 2.729,3.448 1.552,0.24 10 false Front Vertical Motor 2.25,1.573 2.406,1.771 0.156,0.198 10 false 1 2.26,1.083 2.417,1.281 0.156,0.198 10 false 4 2.26,2.063 2.417,2.26 0.156,0.198 10 false 2 2.25,2.583 2.406,2.781 0.156,0.198 10 false 3 4.813,1.177 5.271,1.375 0.458,0.198 10 false d11 4.823,1.677 5.281,1.875 0.458,0.198 10 false d11 4.813,2.188 5.271,2.385 0.458,0.198 10 false d12 4.813,2.688 5.271,2.885 0.458,0.198 10 false d12 4.896,1 5.146,1.198 0.25,0.198 10 false 8 4.896,2.021 5.146,2.219 0.25,0.198 10 false 3 4.885,2.521 5.135,2.719 0.25,0.198 10 false 1 4.896,1.521 5.146,1.719 0.25,0.198 10 false 5 5.135,1.698 5.75,1.896 0.615,0.198 10 false FRV- 5.135,1.188 5.75,1.385 0.615,0.198 10 false FRV+ 5.125,2.208 5.74,2.406 0.615,0.198 10 false SSFV 5.125,2.719 5.74,2.917 0.615,0.198 10 false SGND 4.854,3.844 6.448,4.302 1.594,0.458 10 false Position Control ECU and Switch Assembly


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT VERTICAL MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)

NG

5.INSPECT FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)
a.

Disconnect the e9*1 or d9*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e9-2 - e9-3 Front vertical switch on 4.8 to 5.1 V

for RHD
Tester Connection Condition Specified Condition
d9-2 - d9-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
3.CHECK FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238515
0.729,0.542 1.156,0.833 0.427,0.292 2.229,0.552 2.656,0.844 0.427,0.292 0.198,0.135 0.375,0.302 0.177,0.167 10 false *a 0.865,0.604 1.25,0.844 0.385,0.24 10 false e9 2.375,0.615 2.76,0.854 0.385,0.24 10 false d9 1.229,0.573 1.615,0.813 0.385,0.24 10 false *A 2.708,0.583 3.094,0.823 0.385,0.24 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(Front Vertical Motor (Separate Type Front Seat Cushion Spring Assembly))


Reconnect the e9*1 or d9*2 front vertical motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
e9-2 - Body ground Front vertical switch on 4.5 to 4.8 V

for RHD
Tester Connection Switch Condition Specified Condition
d9-2 - Body ground Front vertical switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
a.

Disconnect the e12*1 or d12*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e12-3 (SSFV) - e9-2 Always Below 1 Ω
e12-1 (SGND) - e9-3 Always Below 1 Ω
e12-3 (SSFV) - Body ground Always 10 kΩ or higher
e12-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d12-3 (SSFV) - d9-2 Always Below 1 Ω
d12-1 (SGND) - d9-3 Always Below 1 Ω
d12-3 (SSFV) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238256
0.107,0.047 0.272,0.21 0.165,0.162 10 *a
*a Component without harness connected
(Front Vertical Motor (Separate Type Front Seat Cushion Spring Assembly))


Disconnect the e9*1 or d9*2 front vertical motor connector.

*1: for LHD

*2: for RHD



b.

Check if the seat cushion spring moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seat cushion spring moves upward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seat cushion spring moves downward



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)

NG

REPLACE FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
a.

Disconnect the e11*1 or d11*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e11-8 (FRV+) - e9-4 Always Below 1 Ω
e11-5 (FRV-) - e9-1 Always Below 1 Ω
e11-8 (FRV+) - Body ground Always 10 kΩ or higher
e11-5 (FRV-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d11-8 (FRV+) - d9-4 Always Below 1 Ω
d11-5 (FRV-) - d9-1 Always Below 1 Ω
d11-8 (FRV+) - Body ground Always 10 kΩ or higher
d11-5 (FRV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR