Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2030EQ _58 Vehicle Interior _014670 SEAT _0077330 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  One or more Power Seat Motors do not Operate  


DESCRIPTION

Signals are input into the position control ECU and switch assembly. The built-in ECU manages the signals received from the front power seat switch, and operates each motor. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B270912
1.677,1.573 2.052,1.75 0.375,0.177 10 false SLD- 1.677,1.198 2.042,1.375 0.365,0.177 10 false SLD+ 1.656,0.469 2.063,0.646 0.406,0.177 10 false SYSB 1.677,2.313 2.229,2.573 0.552,0.26 10 false FRV+ 1.677,2.708 2.219,2.948 0.542,0.24 10 false FRV- 1.708,3.427 2.292,3.688 0.583,0.26 10 false LFT+ 1.729,3.813 2.25,4.042 0.521,0.229 10 false LFT- 1.688,5.458 2.219,5.667 0.531,0.208 10 false RCL+ 1.719,5.844 2.115,6 0.396,0.156 10 false RCL- 4.385,1.188 4.823,1.448 0.438,0.26 10 false e8 4.385,1.594 4.813,1.823 0.427,0.229 10 false e8 4.385,2.302 4.813,2.563 0.427,0.26 10 false e9 4.375,2.708 4.708,2.917 0.333,0.208 10 false e9 4.354,3.438 4.792,3.677 0.438,0.24 10 false e10 4.344,3.833 4.854,4.115 0.51,0.281 10 false e10 4.583,6.094 4.948,6.344 0.365,0.25 10 false g3 4.104,6.49 6.427,6.854 2.323,0.365 10 false Front Seatback Frame Sub-assembly (for Driver) 4.104,4.5 6.271,4.844 2.167,0.344 10 false Separate Type Front Seat Cushion Spring Assembly 1.042,6.885 2.385,7.271 1.344,0.385 10 false Position Control ECU and Switch Assembly 4.521,5.76 4.625,5.927 0.104,0.167 10 false 1 4.417,2.531 4.51,2.708 0.094,0.177 10 false 1 4.417,3.656 4.604,3.875 0.188,0.219 10 false 1 4.417,2.125 4.635,2.375 0.219,0.25 10 false 4 4.521,5.375 4.625,5.552 0.104,0.177 10 false 4 4.417,3.24 4.719,3.552 0.302,0.313 10 false 4 4.875,1.823 5.833,2.063 0.958,0.24 10 false Slide Motor 4.625,2.958 5.99,3.198 1.365,0.24 10 false Front Vertical Motor 4.823,4.073 5.823,4.344 1,0.271 10 false Lifter Motor 4.833,6.094 6.083,6.396 1.25,0.302 10 false Reclining Motor 4.427,1.406 4.542,1.573 0.115,0.167 10 false 1 4.427,1 4.531,1.146 0.104,0.146 10 false 4 2.146,0.469 2.729,0.76 0.583,0.292 10 false e12 0.271,0.073 0.927,0.24 0.656,0.167 12 false for LHD: 2.156,1.198 2.604,1.469 0.448,0.271 10 false e11 2.146,1.594 2.719,1.958 0.573,0.365 10 false e11 2.156,2.313 2.698,2.563 0.542,0.25 10 false e11 2.156,2.708 2.521,2.948 0.365,0.24 10 false e11 2.156,3.448 2.573,3.719 0.417,0.271 10 false e11 2.156,3.833 2.594,4.073 0.438,0.24 10 false e11 2.146,5.458 2.573,5.698 0.427,0.24 10 false e11 2.156,5.854 2.594,6.073 0.438,0.219 10 false e11 2.177,0.281 2.479,0.521 0.302,0.24 10 false 12 2.177,5.656 2.5,5.885 0.323,0.229 10 false 11 2.188,3.656 2.365,3.813 0.177,0.156 10 false 12 2.229,1 2.354,1.156 0.125,0.156 10 false 3 2.229,1.396 2.521,1.656 0.292,0.26 10 false 4 2.229,2.125 2.354,2.281 0.125,0.156 10 false 8 2.177,3.26 2.531,3.531 0.354,0.271 10 false 10 2.219,5.25 2.531,5.563 0.313,0.313 10 false 9 2.229,2.531 2.354,2.688 0.125,0.156 10 false 5 3.771,0.604 4.813,0.833 1.042,0.229 10 false ECU-B NO. 1 5.323,0.458 6.354,0.76 1.031,0.302 10 false from Battery

B270912
1.688,1.583 2.063,1.76 0.375,0.177 10 false SLD- 1.677,1.198 2.042,1.375 0.365,0.177 10 false SLD+ 1.656,0.458 2.198,0.708 0.542,0.25 10 false SYSB 1.656,2.313 2.177,2.542 0.521,0.229 10 false FRV+ 1.667,2.708 2.083,2.885 0.417,0.177 10 false FRV- 1.688,3.448 2.146,3.698 0.458,0.25 10 false LFT+ 1.688,3.833 2.063,4.031 0.375,0.198 10 false LFT- 1.635,5.469 2.073,5.646 0.438,0.177 10 false RCL+ 1.656,5.844 2.052,6 0.396,0.156 10 false RCL- 4.385,1.177 4.729,1.417 0.344,0.24 10 false d8 4.385,1.573 4.698,1.729 0.313,0.156 10 false d8 4.385,2.292 4.719,2.531 0.333,0.24 10 false d9 4.385,2.708 4.719,2.938 0.333,0.229 10 false d9 4.344,3.427 4.677,3.646 0.333,0.219 10 false d10 4.344,3.823 4.656,4 0.313,0.177 10 false d10 4.635,6.083 4.906,6.344 0.271,0.26 10 false f3 4.24,6.521 5.979,7.042 1.74,0.521 10 false Front Seatback Frame Sub-assembly (for Driver) 4.094,4.521 6.219,4.969 2.125,0.448 10 false Separate Type Front Seat Cushion Spring Assembly 0.781,6.938 2.344,7.333 1.563,0.396 10 false Position Control ECU and Switch Assembly 4.51,5.771 4.729,6.031 0.219,0.26 10 false 1 4.417,2.521 4.625,2.781 0.208,0.26 10 false 1 4.417,3.646 4.573,3.844 0.156,0.198 10 false 1 4.417,2.115 4.573,2.333 0.156,0.219 10 false 4 4.51,5.375 4.698,5.646 0.188,0.271 10 false 4 4.417,3.24 4.625,3.479 0.208,0.24 10 false 4 4.813,1.813 5.594,1.958 0.781,0.146 10 false Slide Motor 4.604,2.938 5.969,3.302 1.365,0.365 10 false Front Vertical Motor 4.823,4.052 5.604,4.271 0.781,0.219 10 false Lifter Motor 4.833,6.083 5.948,6.354 1.115,0.271 10 false Reclining Motor 4.406,1.396 4.594,1.615 0.188,0.219 10 false 1 4.427,0.99 4.625,1.188 0.198,0.198 10 false 4 2.146,0.458 2.51,0.688 0.365,0.229 10 false d12 2.146,1.177 2.479,1.354 0.333,0.177 10 false d11 2.156,1.583 2.51,1.792 0.354,0.208 10 false d11 2.146,2.302 2.49,2.521 0.344,0.219 10 false d11 2.156,2.708 2.51,2.938 0.354,0.229 10 false d11 2.146,3.427 2.521,3.646 0.375,0.219 10 false d11 2.156,3.833 2.594,4.125 0.438,0.292 10 false d11 2.156,5.448 2.469,5.635 0.313,0.188 10 false d11 2.146,5.844 2.521,6.167 0.375,0.323 10 false d11 2.188,0.281 2.438,0.49 0.25,0.208 10 false 12 2.177,5.656 2.406,5.844 0.229,0.188 10 false 11 2.167,3.656 2.531,3.969 0.365,0.313 10 false 12 2.229,0.99 2.354,1.146 0.125,0.156 10 false 3 2.229,1.406 2.406,1.625 0.177,0.219 10 false 4 2.229,2.125 2.354,2.281 0.125,0.156 10 false 8 2.177,3.25 2.542,3.542 0.365,0.292 10 false 10 2.229,5.26 2.438,5.5 0.208,0.24 10 false 9 2.229,2.521 2.354,2.677 0.125,0.156 10 false 5 3.771,0.604 4.708,0.823 0.938,0.219 10 false ECU-B NO. 1 5.323,0.458 6.677,0.635 1.354,0.177 10 false from Battery 0.208,0.229 0.865,0.563 0.656,0.333 12 false for RHD:

B293934
0.344,2.146 1.958,2.479 1.615,0.333 10 false Position Control ECU and Switch Assembly 2.375,2.083 3.99,2.417 1.615,0.333 10 false Front Lumbar Power Seat Switch 4.938,1.969 6.5,2.427 1.563,0.458 10 false Lumbar Support Adjuster Assembly (for Driver) 4.938,1.792 5.729,2.063 0.792,0.271 10 false g2*1, f2*2 4.708,0.583 5.083,0.854 0.375,0.271 10 false 1*2 3.656,0.583 3.896,0.75 0.24,0.167 10 false 1 4.719,1.344 5.188,1.583 0.469,0.24 10 false 2*2 3.646,1.354 3.885,1.521 0.24,0.167 10 false 3 1.135,0.781 1.552,0.948 0.417,0.167 10 false GND2 1.271,1.573 1.563,1.74 0.292,0.167 10 false +B2 2.615,0.698 2.76,0.865 0.146,0.167 10 false 2 1.594,0.688 1.74,0.854 0.146,0.167 10 false 1 1.594,1.458 1.74,1.625 0.146,0.167 10 false 6 2.615,1.479 2.76,1.646 0.146,0.167 10 false 5 0.344,1.823 0.802,2.281 0.458,0.458 10 false e11*1, d11*2 2.375,1.76 2.75,2.115 0.375,0.354 10 false e5*1, d5*2 4.729,1.146 5.198,1.385 0.469,0.24 10 false 1*1 4.708,0.427 5.083,0.698 0.375,0.271 10 false 2*1 1.792,0.052 2.563,0.281 0.771,0.229 10 false *1: for LHD 1.792,0.323 2.563,0.552 0.771,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
One or more power seat functions (except lumbar support adjustment function) do not operate A
All power seat functions do not operate B
Front vertical and lifter functions do not operate C
Only lumbar support adjustment function does not operate D




A

2.READ VALUE USING INTELLIGENT TESTER (POWER SEAT SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Front Power Seat does not Operate with Front Power Seat Switch)

C

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY)

D

8.INSPECT LUMBAR FRONT POWER SEAT SWITCH
2.READ VALUE USING INTELLIGENT TESTER (POWER SEAT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Lifter switch signal (Downward) ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up Lifter switch signal (Upward) ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear Slide switch signal (Rearward) ON or OFF ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off
-
Slide Front Slide switch signal (Forward) ON or OFF ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off
-
Body Electrical > Driver Seat > Data List
Tester Display
Reclining Rear
Reclining Front
Front Vertical Down
Front Vertical Up
Lifter Switch Down
Lifter Switch Up
Slide Rear
Slide Front
50003 162 17,18,19,20,21,22,23,24
OK:

ON or OFF is displayed on the intelligent tester according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Lifter Operation Seat lifter operation OFF/Down/Up -
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
Result:
Result Proceed to
The power seat functions operate normally. A
Slide, front vertical or lifter function does not operate normally. B
Reclining function does not operate normally. C




A

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

C

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER)
4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.
B238256
0.104,0.052 0.271,0.219 0.167,0.167 10 *a
*a Component without harness connected
(Slide Motor (Separate Type Front Seat Cushion Spring Assembly))


Disconnect the e8*1, e9*1, e10*1, d8*2, d9*2 or d10*2 connector from each motor.

*1: for LHD

*2: for RHD


HINT:

Check the motor operation of applicable function.



b.

Check the operation of the slide motor.

i.

Check if the seat cushion moves smoothly when the battery is connected to the slide motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seat cushion spring moves forward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seat cushion spring moves backward




c.
B238256
0.104,0.052 0.271,0.219 0.167,0.167 10 *a
*a Component without harness connected
(Front Vertical Motor (Separate Type Front Seat Cushion Spring Assembly))


Check the operation of the front vertical motor.

i.

Check if the seat cushion moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seat cushion spring moves upward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seat cushion spring moves downward




d.
B238256
0.104,0.052 0.271,0.219 0.167,0.167 10 *a
*a Component without harness connected
(Lifter Motor (Separate Type Front Seat Cushion Spring Assembly))


Check the operation of the lifter motor.

i.

Check if the seat cushion spring moves smoothly when the battery is connected to the lifter motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seat cushion spring moves upward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seat cushion spring moves downward


Result:
Proceed to
OK
NG





OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER)
a.
B238256
0.104,0.052 0.271,0.219 0.167,0.167 10 *a
*a Component without harness connected
(Reclining Motor (Front Seatback Frame Sub-assembly (for Driver)))


Disconnect g3*1 or f3*2 reclining motor connector.

*1: for LHD

*2: for RHD



b.

Check the operation of the reclining motor.

i.

Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 4
Battery negative (-) → Terminal 1
Seatback moves forward
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 4
Seatback moves backward




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)

NG

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY (FOR DRIVER)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)
a.

Disconnect the e11*1 or d11*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU and switch assembly and applicable motor.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e11-3 (SLD+) - e8-4 Always Below 1 Ω
e11-4 (SLD-) - e8-1 Always Below 1 Ω
e11-5 (FRV-) - e9-1 Always Below 1 Ω
e11-8 (FRV+) - e9-4 Always Below 1 Ω
e11-10 (LFT+) - e10-4 Always Below 1 Ω
e11-12 (LFT-) - e10-1 Always Below 1 Ω
e11-9 (RCL+) - g3-4 Always Below 1 Ω
e11-11 (RCL-) - g3-1 Always Below 1 Ω
e11-3 (SLD+) - Body ground Always 10 kΩ or higher
e11-4 (SLD-) - Body ground Always 10 kΩ or higher
e11-5 (FRV-) - Body ground Always 10 kΩ or higher
e11-8 (FRV+) - Body ground Always 10 kΩ or higher
e11-10 (LFT+) - Body ground Always 10 kΩ or higher
e11-12 (LFT-) - Body ground Always 10 kΩ or higher
e11-9 (RCL+) - Body ground Always 10 kΩ or higher
e11-11 (RCL-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d11-3 (SLD+) - d8-4 Always Below 1 Ω
d11-4 (SLD-) - d8-1 Always Below 1 Ω
d11-5 (FRV-) - d9-1 Always Below 1 Ω
d11-8 (FRV+) - d9-4 Always Below 1 Ω
d11-10 (LFT+) - d10-4 Always Below 1 Ω
d11-12 (LFT-) - d10-1 Always Below 1 Ω
d11-9 (RCL+) - f3-4 Always Below 1 Ω
d11-11 (RCL-) - f3-1 Always Below 1 Ω
d11-3 (SLD+) - Body ground Always 10 kΩ or higher
d11-4 (SLD-) - Body ground Always 10 kΩ or higher
d11-5 (FRV-) - Body ground Always 10 kΩ or higher
d11-8 (FRV+) - Body ground Always 10 kΩ or higher
d11-10 (LFT+) - Body ground Always 10 kΩ or higher
d11-12 (LFT-) - Body ground Always 10 kΩ or higher
d11-9 (RCL+) - Body ground Always 10 kΩ or higher
d11-11 (RCL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the e12*1 or d12*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e12-12 (SYSB) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
d12-12 (SYSB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT LUMBAR FRONT POWER SEAT SWITCH
a.

Remove the lumbar front power seat switch.

Click hereVehicle Interior>SEAT>LUMBAR SWITCH>REMOVAL


b.
B239575
2.542,1.125 2.083,1.125 false 1.458,1.135 1,1.135 false 2.583,1.063 2.823,1.333 0.24,0.271 10 false *2 0.854,1.063 1.177,1.406 0.323,0.344 10 false *1 1.688,2.521 2.052,2.771 0.365,0.25 10 false *a
*1
·

Hold Switch (for LHD)

·

Release Switch (for RHD)


*2
·

Release Switch (for LHD)

·

Hold Switch (for RHD)


*a Component without harness connected
(Front Lumbar Power Seat Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3 - 5 Hold Below 1 Ω
1 - 2
2 - 3 Off
1 - 2
2 - 3 Release
1 - 5

for RHD
Tester Connection Condition Specified Condition
1 - 5 Hold Below 1 Ω
2 - 3
1 - 2 Off
2 - 3
1 - 2 Release
3 - 5



Result:
Proceed to
OK
NG



OK

9.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (FOR DRIVER)

NG

REPLACE FRONT LUMBAR POWER SEAT SWITCH

9.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (FOR DRIVER)
a.
B161051
0.116,0.074 0.321,0.245 0.205,0.17 10 *a
*a Component without harness connected
(Lumbar Support Adjuster Assembly (for Driver))


Disconnect g2*1 or f2*2 lumbar support adjuster assembly (for Driver) connector.

*1: for LHD

*2: for RHD



b.

Check the operation of the lumbar support adjuster assembly (for Driver).

i.

Check that the seatback moves smoothly when the battery is connected to the lumbar support adjuster assembly (for Driver) connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Seatback moves forward
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Seatback moves backward




Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT LUMBAR POWER SEAT SWITCH - LUMBAR MOTOR)

NG

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY (FOR DRIVER)

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT LUMBAR POWER SEAT SWITCH - LUMBAR MOTOR)
a.

Disconnect the e11*1 or d11*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e11-6 (+B2) - e5-5 Always Below 1 Ω
e11-1 (GND2) - e5-2 Always Below 1 Ω
e5-3 - g2-1 Always Below 1 Ω
e5-1 - g2-2 Always Below 1 Ω
e5-5 - Body ground Always 10 kΩ or higher
e5-2 - Body ground Always 10 kΩ or higher
e5-3 - Body ground Always 10 kΩ or higher
e5-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d11-6 (+B2) - d5-5 Always Below 1 Ω
d11-1 (GND2) - d5-2 Always Below 1 Ω
d5-3 - f2-2 Always Below 1 Ω
d5-1 - f2-1 Always Below 1 Ω
d5-5 - Body ground Always 10 kΩ or higher
d5-2 - Body ground Always 10 kΩ or higher
d5-3 - Body ground Always 10 kΩ or higher
d5-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR