Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2014.05–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E237385E03
0.458,1.438 1.583,1.583 1.125,0.146 10 false Skid Control ECU 0.865,0.583 1.156,0.729 0.292,0.146 10 false SP1 0.156,1.438 0.479,1.615 0.323,0.177 10 false A49 1.208,0.583 1.396,0.729 0.188,0.146 10 false 2 0.115,2.74 3.198,2.906 3.083,0.167 10 false Certification ECU (Smart Key ECU Assembly)*5 0.115,2.583 0.406,2.75 0.292,0.167 10 false I78 1.635,2.333 2.031,2.49 0.396,0.156 10 false SPD 2.104,2.333 2.281,2.49 0.177,0.156 10 false 27 2.927,2.333 3.104,2.49 0.177,0.156 10 false 19 3.938,2.333 4.115,2.49 0.177,0.156 10 false 18 5.417,0.563 5.719,0.708 0.302,0.146 10 false 8 5.417,2.344 5.688,2.49 0.271,0.146 10 false 9 5.594,0.667 5.792,0.813 0.198,0.146 10 false SI 5.583,2.448 5.781,2.594 0.198,0.146 10 false +S 5.01,2.792 5.344,2.938 0.333,0.146 10 false I18 5.281,2.792 7.115,2.99 1.833,0.198 10 false Combination Meter Assembly 4.531,7.49 4.792,7.656 0.26,0.167 10 false I72 4.844,7.49 7.156,7.813 2.313,0.323 10 false Windshield Wiper Relay Assembly*4 5.635,7.188 6.052,7.344 0.417,0.156 10 false SPD 2.938,3.771 3.115,3.927 0.177,0.156 10 false 20 3.948,3.771 4.125,3.927 0.177,0.156 10 false 17 5.365,7.104 5.552,7.26 0.188,0.156 10 false 24 3.958,7.104 4.146,7.26 0.188,0.156 10 false 21 2.938,7.104 3.125,7.26 0.188,0.156 10 false 16 2.104,7.104 2.302,7.271 0.198,0.167 10 false 10 5.302,5.115 5.521,5.281 0.219,0.167 10 false 17 1.167,7.5 1.448,7.656 0.281,0.156 10 false A25 1.49,7.5 1.896,7.677 0.406,0.177 10 false ECM 4.417,5.656 6.948,6.115 2.531,0.458 10 false Navigation ECU Sub-assembly*2 or Radio and Display Receiver Assembly*3 2.365,8.26 4.76,8.427 2.396,0.167 10 false *5: w/ Smart Entry and Start System 0.323,8.26 2,8.417 1.677,0.156 10 false *4: w/ Auto Wiper System 4.813,7.938 6.719,8.115 1.906,0.177 10 false *3: for Radio and Display Type 1.677,7.104 2,7.25 0.323,0.146 10 false SPD 2.115,5.208 2.313,5.375 0.198,0.167 10 false 3 1.271,5.615 1.719,5.771 0.448,0.156 10 false E7 1.5,5.615 1.906,5.792 0.406,0.177 10 false TCM 1.688,5.208 2.01,5.354 0.323,0.146 10 false SPD 5.594,5.219 5.917,5.365 0.323,0.146 10 false SPD 5.594,3.792 5.917,3.938 0.323,0.146 10 false SPD 5.25,5.292 5.573,5.438 0.323,0.146 10 false I155 5.313,5.49 5.5,5.635 0.188,0.146 10 false *3 4.948,5.115 5.167,5.281 0.219,0.167 10 false 17 4.938,5.292 5.208,5.438 0.271,0.146 10 false I67 4.948,5.49 5.135,5.635 0.188,0.146 10 false *2 2.115,3.781 2.427,3.948 0.313,0.167 10 false 11 0.604,4.156 0.875,4.313 0.271,0.156 10 false I69 5.333,3.792 5.646,3.958 0.313,0.167 10 false 17 5,4.167 5.542,4.323 0.542,0.156 10 false I150 0.906,4.156 2.229,4.646 1.323,0.49 10 false Stereo Component Amplifier Assembly*2 5.333,4.167 7.083,4.344 1.75,0.177 10 false Radio Receiver Assembly*1 1.719,3.854 2.042,4 0.323,0.146 10 false SPD 2.448,7.938 4.49,8.115 2.042,0.177 10 false *2: for Navigation Receiver Type 0.323,7.938 2.115,8.104 1.792,0.167 10 false *1: for Radio Receiver Type 3.104,7.521 4.323,7.688 1.219,0.167 10 false Junction Connector 2.792,7.521 3.188,7.688 0.396,0.167 10 false I124

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E263768C02
1.521,0.448 1.885,0.688 0.365,0.24 0.958,2.104 1.365,1.521 false 0.146,0.125 0.458,0.323 0.313,0.198 10 *a 1.615,0.49 1.948,0.688 0.333,0.198 10 I18 1.094,4.063 1.615,4.281 0.521,0.219 10 (A) 0.844,2.135 1.177,2.333 0.333,0.198 10 +S 2.792,3.719 3.313,3.938 0.521,0.219 10 GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-9 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E277148C02
1.563,0.406 1.917,0.646 0.354,0.24 0.885,2.115 1.177,1.479 false 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 0.698,2.167 1.281,2.417 0.583,0.25 10 false SPD 1.667,0.438 1.979,0.635 0.313,0.198 10 false I69 0.969,3.948 1.281,4.146 0.313,0.198 10 false (A) 2.677,3.646 3.229,3.938 0.552,0.292 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Check the input waveform.

i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal I69-11 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I69-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the stereo component amplifier assembly connector.


b.

Disconnect the junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-11 (SPD) - I124-20 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)