Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2015.04
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0164667 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Leveling ECU Power Source Circuit  


DESCRIPTION

This circuit detects the state of the engine switch, and sends it to the headlight leveling ECU assembly.

WIRING DIAGRAM

E223770E21
4.844,2.76 7.021,2.948 2.177,0.188 10 false Headlight Leveling ECU Assembly 4.844,2.583 5.125,2.771 0.281,0.188 10 false A78 0.615,1.063 1.979,1.25 1.365,0.188 10 false from IG1 NO. 1 Relay 5.479,1.083 5.677,1.281 0.198,0.198 10 false IG 5.479,2.167 5.677,2.365 0.198,0.198 10 false E1 5.281,2.063 5.385,2.208 0.104,0.146 10 false 9 5.271,0.969 5.396,1.146 0.125,0.177 10 false 1 3.51,1.229 4.135,1.427 0.625,0.198 10 false H-LP LVL

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
+B IG power supply voltage value 0.00 to 19.75 V 11 to 14 V -
Body Electrical > HL AutoLeveling > Data List
Tester Display
+B
50003 165 7
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT LEVELING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the A78 headlight leveling ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A78-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
A78-1 (IG) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A78-9 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR