Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2015.04
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0164667 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Headlight Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly detects the status of the low beam headlights.

WIRING DIAGRAM

E220272E15
0.927,0.885 1.313,1.063 0.385,0.177 10 false HRLY 5.844,0.885 6.104,1.063 0.26,0.177 10 false B2 4.146,1.281 5.219,1.458 1.073,0.177 10 false from H-LP Relay 0.156,2.448 0.417,2.625 0.26,0.177 10 false MB 0.156,2.615 1.802,2.948 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 1.438,1.646 3.063,1.979 1.625,0.333 10 false Instrument Panel Junction Block Assembly 5.406,2.573 5.76,2.76 0.354,0.188 10 false A78 5.396,2.74 6.885,3.073 1.49,0.333 10 false Headlight Leveling ECU Assembly 5.677,0.792 5.771,0.969 0.094,0.177 10 false 3 1.396,0.792 1.573,0.969 0.177,0.177 10 false 15 2.781,0.698 2.958,0.875 0.177,0.177 10 false 11 2.781,0.896 3,1.073 0.219,0.177 10 false 3D 2.781,1.094 2.958,1.271 0.177,0.177 10 false 12 2.781,1.292 3,1.469 0.219,0.177 10 false 3D

CAUTION / NOTICE / HINT

NOTICE:

First check that the low beam headlights operate normally.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Headlight Low Beam State Low beam headlight state ON or OFF ON: Low beam headlights on
OFF: Low beam headlights off
-
Body Electrical > HL AutoLeveling > Data List
Tester Display
Headlight Low Beam State
50003 165 3
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Disconnect the A78 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-11 - A78-3 (B2) Always Below 1 Ω
3D-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E231983C02
1.5,0.354 1.99,0.646 0.49,0.292 0.125,0.115 0.688,0.583 0.563,0.469 10 *a 1.656,0.417 2.156,0.802 0.5,0.385 10 3D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-11 - 3D-12 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY