Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A115899E21
0.766,1.047 1.553,1.425 0.787,0.378 10 from Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.498,1.96 5.333,2.123 1.835,0.163 10 Combination Meter Assembly 3.113,0.599 3.921,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.068,1.841 6.515,2.004 0.448,0.163 10 ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (1 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Vehicle speed sensor
Combination meter assembly
Skid control ECU
Required Sensors/Components (Related) Park/Neutral position switch assembly
Engine coolant temperature sensor
Crankshaft position sensor
Throttle position sensor
Mass air flow meter sub-assembly
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Transaxle counter gear revolution 300 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No signal

CONFIRMATION DRIVING PATTERN

A198825E35
1.281,0.823 1.833,1.052 0.552,0.229 10 false 24 km/h 1.417,2 1.813,2.167 0.396,0.167 10 false Idling 0.406,2.375 1.865,2.677 1.458,0.302 10 false Engine Switch on (IG) 2.385,2.219 2.615,2.385 0.229,0.167 10 false [A] 4.708,0.417 4.917,0.583 0.208,0.167 10 false [B] 6.25,3.229 6.448,3.427 0.198,0.198 10 false [C] 3.719,2.969 5.635,3.115 1.917,0.146 10 false Total of 30 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0500.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

E316128E01
0.146,2.438 3.052,2.625 2.906,0.188 10 false Certification ECU (Smart Key ECU Assembly) 0.24,3.677 2.927,3.865 2.688,0.188 10 false Stereo Component Amplifier Assembly*4 0.365,4.906 2.771,5.146 2.406,0.24 10 false Windshield Wiper Relay Assembly*5 4.99,3.698 7.052,3.927 2.063,0.229 10 false Navigation Receiver Assembly*1 0.427,6.083 2.75,6.302 2.323,0.219 10 false Headlight Leveling ECU Assembly*6 4.625,4.917 7.104,5.146 2.479,0.229 10 false Radio and Display Receiver Assembly*2 5.156,6.094 6.885,6.313 1.729,0.219 10 false Radio Receiver Assembly*3 6.042,7.302 6.469,7.5 0.427,0.198 10 false ECM 5.198,2.51 7.052,2.719 1.854,0.208 10 false Combination Meter Assembly 0.479,1.281 3.313,1.49 2.833,0.208 10 false Brake Actuator Assembly (Skid Control ECU) 2.823,5.135 4.094,5.333 1.271,0.198 10 false Junction Connector 1.344,7.323 1.75,7.531 0.406,0.208 10 false TCM 0.344,7.927 2.313,8.156 1.969,0.229 10 false *1: for Navigation Receiver Type 2.656,7.917 4.625,8.146 1.969,0.229 10 false *2: for Radio and Display Type 4.865,7.927 6.833,8.156 1.969,0.229 10 false *3: for Radio Receiver Type 0.344,8.333 2.313,8.563 1.969,0.229 10 false *4: for 10 Speakers 1.792,8.344 3.542,8.583 1.75,0.24 10 false *5: w/ Auto Wiper System 3.635,8.333 7.073,8.573 3.438,0.24 10 false *6: w/ Automatic Headlight Beam Level Control System 0.156,1.292 0.49,1.5 0.333,0.208 10 false A49 0.167,2.26 0.5,2.469 0.333,0.208 10 false I78 0.25,3.51 0.583,3.719 0.333,0.208 10 false I69 0.365,4.74 0.698,4.948 0.333,0.208 10 false I72 0.427,5.927 0.76,6.135 0.333,0.208 10 false A78 1.083,7.323 1.333,7.531 0.25,0.208 10 false E7 5.719,7.302 6.052,7.51 0.333,0.208 10 false A25 5.156,5.917 5.573,6.125 0.417,0.208 10 false I150 4.635,4.75 5.052,4.958 0.417,0.208 10 false I155 4.99,3.521 5.406,3.729 0.417,0.208 10 false I67 5.198,2.344 5.615,2.552 0.417,0.208 10 false I18 1.708,1.99 2.042,2.198 0.333,0.208 10 false SPD 1.698,3.25 2.031,3.458 0.333,0.208 10 false SPD 1.688,4.458 2.021,4.667 0.333,0.208 10 false SPD 1.615,5.635 2.052,5.833 0.438,0.198 10 false SPDR 1.708,6.854 2.063,7.021 0.354,0.167 10 false SPD 5.594,6.854 5.948,7.021 0.354,0.167 10 false SPD 5.594,5.635 5.948,5.802 0.354,0.167 10 false SPD 5.594,4.458 5.948,4.625 0.354,0.167 10 false SPD 5.594,3.24 5.948,3.406 0.354,0.167 10 false SPD 0.854,0.396 1.188,0.604 0.333,0.208 10 false SP1 2.823,4.969 3.156,5.177 0.333,0.208 10 false I185 1.229,0.396 1.563,0.604 0.333,0.208 10 false 2 2.104,2 2.438,2.208 0.333,0.208 10 false 27 2.094,3.25 2.427,3.458 0.333,0.208 10 false 11 2.115,4.458 2.448,4.667 0.333,0.208 10 false 24 2.104,5.635 2.438,5.844 0.333,0.208 10 false 16 2.115,6.854 2.448,7.063 0.333,0.208 10 false 3 5.333,6.844 5.5,7.094 0.167,0.25 10 false 10 5.323,5.635 5.49,5.802 0.167,0.167 10 false 17 5.313,4.458 5.479,4.625 0.167,0.167 10 false 17 5.323,3.24 5.49,3.406 0.167,0.167 10 false 17 5.385,0.406 5.552,0.615 0.167,0.208 10 false 4 5.375,1.99 5.542,2.198 0.167,0.208 10 false 3 5.604,2.073 5.854,2.281 0.25,0.208 10 false +S 5.615,0.479 5.865,0.688 0.25,0.208 10 false SI 3.948,1.99 4.115,2.198 0.167,0.208 10 false 18 2.906,1.99 3.073,2.198 0.167,0.208 10 false 15 2.906,3.25 3.073,3.458 0.167,0.208 10 false 19 3.958,3.25 4.125,3.458 0.167,0.208 10 false 17 2.917,4.438 3.083,4.646 0.167,0.208 10 false 20 3.938,4.448 4.104,4.656 0.167,0.208 10 false 16

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 234 10

d.

Drive the vehicle.


e.

Read the value displayed on the GTS.


Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (+S) - A25-10 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234
HINT:

If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END