Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM2030EQ _58 Vehicle Interior _014667 METER / GAUGE / DISPLAY _0074615 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU which uses this information to create the vehicle speed sensor signal*a. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.

*a: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E316128E01
0.146,2.438 3.052,2.625 2.906,0.188 10 false Certification ECU (Smart Key ECU Assembly) 0.24,3.677 2.927,3.865 2.688,0.188 10 false Stereo Component Amplifier Assembly*4 0.365,4.906 2.771,5.146 2.406,0.24 10 false Windshield Wiper Relay Assembly*5 4.99,3.698 7.052,3.927 2.063,0.229 10 false Navigation Receiver Assembly*1 0.427,6.083 2.75,6.302 2.323,0.219 10 false Headlight Leveling ECU Assembly*6 4.625,4.917 7.104,5.146 2.479,0.229 10 false Radio and Display Receiver Assembly*2 5.156,6.094 6.885,6.313 1.729,0.219 10 false Radio Receiver Assembly*3 6.042,7.302 6.469,7.5 0.427,0.198 10 false ECM 5.198,2.51 7.052,2.719 1.854,0.208 10 false Combination Meter Assembly 0.479,1.281 3.313,1.49 2.833,0.208 10 false Brake Actuator Assembly (Skid Control ECU) 2.823,5.135 4.094,5.333 1.271,0.198 10 false Junction Connector 1.344,7.323 1.75,7.531 0.406,0.208 10 false TCM 0.344,7.927 2.313,8.156 1.969,0.229 10 false *1: for Navigation Receiver Type 2.656,7.917 4.625,8.146 1.969,0.229 10 false *2: for Radio and Display Type 4.865,7.927 6.833,8.156 1.969,0.229 10 false *3: for Radio Receiver Type 0.344,8.333 2.313,8.563 1.969,0.229 10 false *4: for 10 Speakers 1.792,8.344 3.542,8.583 1.75,0.24 10 false *5: w/ Auto Wiper System 3.635,8.333 7.073,8.573 3.438,0.24 10 false *6: w/ Automatic Headlight Beam Level Control System 0.156,1.292 0.49,1.5 0.333,0.208 10 false A49 0.167,2.26 0.5,2.469 0.333,0.208 10 false I78 0.25,3.51 0.583,3.719 0.333,0.208 10 false I69 0.365,4.74 0.698,4.948 0.333,0.208 10 false I72 0.427,5.927 0.76,6.135 0.333,0.208 10 false A78 1.083,7.323 1.333,7.531 0.25,0.208 10 false E7 5.719,7.302 6.052,7.51 0.333,0.208 10 false A25 5.156,5.917 5.573,6.125 0.417,0.208 10 false I150 4.635,4.75 5.052,4.958 0.417,0.208 10 false I155 4.99,3.521 5.406,3.729 0.417,0.208 10 false I67 5.198,2.344 5.615,2.552 0.417,0.208 10 false I18 1.708,1.99 2.042,2.198 0.333,0.208 10 false SPD 1.698,3.25 2.031,3.458 0.333,0.208 10 false SPD 1.688,4.458 2.021,4.667 0.333,0.208 10 false SPD 1.615,5.635 2.052,5.833 0.438,0.198 10 false SPDR 1.708,6.854 2.063,7.021 0.354,0.167 10 false SPD 5.594,6.854 5.948,7.021 0.354,0.167 10 false SPD 5.594,5.635 5.948,5.802 0.354,0.167 10 false SPD 5.594,4.458 5.948,4.625 0.354,0.167 10 false SPD 5.594,3.24 5.948,3.406 0.354,0.167 10 false SPD 0.854,0.396 1.188,0.604 0.333,0.208 10 false SP1 2.823,4.969 3.156,5.177 0.333,0.208 10 false I185 1.229,0.396 1.563,0.604 0.333,0.208 10 false 2 2.104,2 2.438,2.208 0.333,0.208 10 false 27 2.094,3.25 2.427,3.458 0.333,0.208 10 false 11 2.115,4.458 2.448,4.667 0.333,0.208 10 false 24 2.104,5.635 2.438,5.844 0.333,0.208 10 false 16 2.115,6.854 2.448,7.063 0.333,0.208 10 false 3 5.333,6.844 5.5,7.094 0.167,0.25 10 false 10 5.323,5.635 5.49,5.802 0.167,0.167 10 false 17 5.313,4.458 5.479,4.625 0.167,0.167 10 false 17 5.323,3.24 5.49,3.406 0.167,0.167 10 false 17 5.385,0.406 5.552,0.615 0.167,0.208 10 false 4 5.375,1.99 5.542,2.198 0.167,0.208 10 false 3 5.604,2.073 5.854,2.281 0.25,0.208 10 false +S 5.615,0.479 5.865,0.688 0.25,0.208 10 false SI 3.948,1.99 4.115,2.198 0.167,0.208 10 false 18 2.906,1.99 3.073,2.198 0.167,0.208 10 false 15 2.906,3.25 3.073,3.458 0.167,0.208 10 false 19 3.958,3.25 4.125,3.458 0.167,0.208 10 false 17 2.917,4.438 3.083,4.646 0.167,0.208 10 false 20 3.938,4.448 4.104,4.656 0.167,0.208 10 false 16

PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
E224284C71
0.313,1.635 0.771,1.917 0.458,0.281 1.229,1.917 1.229,0.688 1.229,0.688 1.427,0.688 false 0.115,0.073 0.396,0.354 0.281,0.281 10 false *a 1.479,0.604 1.74,0.844 0.26,0.24 10 false +S 0.448,1.688 0.802,1.875 0.354,0.188 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-3 (+S) - Body ground Engine switch on (IG) 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Reconnect the I18 combination meter assembly connector.


b.
C238832C13
1.479,0.604 1.938,0.885 0.458,0.281 1,1.948 1,2.604 false 0.156,0.146 0.708,0.49 0.552,0.344 10 false *a 0.875,2.625 1.563,3.01 0.688,0.385 10 false SP1 1.583,0.667 2.229,1.031 0.646,0.365 10 false A49
*a Front view of wire harness connector
(to Brake Actuator Assembly (Skid Control ECU))


Disconnect the A49 brake actuator assembly (skid control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-2 (SP1) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)
a.
E262474C06
1.5,0.292 1.917,0.5 0.417,0.208 2.031,1.271 2.344,0.542 2.344,0.542 2.49,0.542 false 0.25,0.177 0.563,0.333 0.313,0.156 10 false *a 1.615,0.313 1.99,0.573 0.375,0.26 10 false I18 1.292,4 1.542,4.198 0.25,0.198 10 false A 2.927,3.698 3.333,3.906 0.406,0.208 10 false GND 2.563,0.469 2.76,0.625 0.198,0.156 10 false SI
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Reconnect the A49 brake actuator assembly (skid control ECU) connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal I18-4 (SI) and body ground.


iv.

Turn the engine switch on (IG).


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Engine switch on (IG), wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
a.

Disconnect the I18 combination meter assembly and A49 brake actuator assembly (skid control ECU) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-2 (SP1) - I18-4 (SI) Always Below 1 Ω
A49-2 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I185 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (+S) - I185-18 Always Below 1 Ω
I18-3 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)
a.

Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.


i.

Disconnect the I185 junction connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I185-15 - Body ground Engine switch on (IG) 4.5 to 14 V
I185-19 - Body ground Engine switch on (IG) 4.5 to 14 V
I185-17 - Body ground Engine switch on (IG) 4.5 to 14 V
I185-16 - Body ground Engine switch on (IG) 4.5 to 14 V
I185-20 - Body ground Engine switch on (IG) 4.5 to 14 V




Result:
Result Proceed to
Voltage is not present in one circuit. A
Voltage is present in all the circuits. B



A

7.SYSTEM CHECK

B

REPLACE JUNCTION CONNECTOR (INSTRUMENT PANEL WIRE)

7.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 6.


Result:
Tester Connection System that uses the circuit Proceed to
I185-15 - Body ground Smart entry and start system A
I185-19 - Body ground Navigation system*2 B
I185-17 - Body ground Audio and visual system*3, *4 or Navigation system*5 C
I185-16 - Body ground SFI system, U660E automatic transaxle system, Automatic headlight beam level control system*6 D
I185-20 - Body ground Wiper and washer system*1 E


*1: w/ Auto Wiper System

*2: for 10 Speakers

*3: for Radio Receiver Type

*4: for Radio and Display Type

*5: for Navigation Receiver Type

*6: w/ Automatic Headlight Beam Level Control System



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CIRCUIT)

B

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)

C

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT, NAVIGATION RECEIVER ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT)

D

11.CONFIRM VEHICLE TYPE

E

17.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CIRCUIT)
a.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-27 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)
a.

Disconnect the I69 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-11 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT, NAVIGATION RECEIVER ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT)
a.

Disconnect the I150 radio receiver assembly*1 or I67 navigation receiver assembly*2 or I155 radio and display receiver assembly*3 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I150-17 (SPD)*1 - Body ground Always 10 kΩ or higher
I67-17 (SPD)*2 - Body ground Always 10 kΩ or higher
I155-17 (SPD)*3 - Body ground Always 10 kΩ or higher


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type



Result:
Result Proceed to
OK (for Radio Receiver Type) A
OK (for Navigation Receiver Type) B
OK (for Radio and Display Type) C
NG D



A

REPLACE RADIO RECEIVER ASSEMBLY

B

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CONFIRM VEHICLE TYPE
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Automatic Headlight Beam Level Control System A
w/o Automatic Headlight Beam Level Control System B



A

12.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - EACH ECU)

B

15.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - EACH ECU)
12.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - EACH ECU)
a.

Disconnect the A78 headlight leveling ECU assembly connector.


b.

Disconnect the A25 ECM connector.


c.

Disconnect the E7 TCM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I185-16 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY (SHORT CIRCUIT IN HEADLIGHT LEVELING ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY (SHORT CIRCUIT IN HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Reconnect the A25 ECM connector.


b.

Reconnect the E7 TCM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I185-16 - Body ground Engine switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the headlight leveling ECU assembly.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

14.INSPECT ECM (SHORT CIRCUIT IN ECM)
14.INSPECT ECM (SHORT CIRCUIT IN ECM)
a.

Reconnect the A78 headlight leveling ECU assembly connector.


b.

Disconnect the A25 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I185-16 - Body ground Engine switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the ECM.



Result:
Proceed to
OK
NG



OK

NG

15.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - EACH ECU)
a.

Disconnect the A25 ECM connector.


b.

Disconnect the E7 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I185-16 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT ECM (SHORT CIRCUIT IN ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT ECM (SHORT CIRCUIT IN ECM)
a.

Reconnect the E7 TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I185-16 - Body ground Engine switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the ECM.



Result:
Proceed to
OK
NG



OK

NG

17.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)
a.

Disconnect the I72 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR