Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2015.04
RM2030EQ _51 Engine / Hybrid System _014642 CRUISE CONTROL _0165902 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  C1AA6  Yaw Rate Sensor Zero Point Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives vehicle stability signals from the airbag sensor assembly (yaw rate sensor) and sends the signals to the lane departure warning camera. If the skid control ECU (brake actuator assembly) or airbag sensor assembly (yaw rate sensor) detects that the airbag sensor assembly (yaw rate sensor) is malfunctioning, the skid control ECU (brake actuator assembly) or airbag sensor assembly (yaw rate sensor) sends a malfunction signal to the lane departure warning camera and the lane departure warning camera stores DTC C1AA4, C1AA5 or C1AA6.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit While driving with the lane departure alert system activated, an airbag sensor assembly (yaw rate sensor) malfunction signal sent from the airbag sensor assembly (yaw rate sensor) to the lane departure warning camera is detected for 5 seconds or more.
·

Lane departure warning camera

·

Airbag sensor assembly (Yaw rate sensor)


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit While driving with the lane departure alert system activated, an airbag sensor assembly (yaw rate sensor) power supply voltage malfunction signal sent from the airbag sensor assembly (yaw rate sensor) to the lane departure warning camera is detected for 5 seconds or more.
·

Lane departure warning camera

·

Airbag sensor assembly (Yaw rate sensor)


C1AA6 Yaw Rate Sensor Zero Point Malfunction While driving with the lane departure alert system activated, an airbag sensor assembly (yaw rate sensor) zero point malfunction signal sent from the skid control ECU (brake actuator assembly) to the lane departure warning camera is detected for 5 seconds or more.
·

Vehicle stability control system

·

Lane departure warning camera



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

When replacing the lane departure warning camera, always replace it with a new one. If a lane departure warning camera which was installed to another vehicle is used, the information stored in the lane departure warning camera will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCS (AIRBAG SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output A
Airbag system DTCs are output B




A

2.CHECK FOR DTCS (VEHICLE STABILITY CONTROL SYSTEM)

B

2.CHECK FOR DTCS (VEHICLE STABILITY CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B




A

3.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)

B

3.CHECK FOR DTCS (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Result Proceed to
DTC C1AA4, C1AA5 and C1AA6 are not output A
DTC C1AA4, C1AA5 or C1AA6 is output B



A

B