DTC CHECK/CLEAR (When Using the Intelligent Tester)
Check for DTCs.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Read the DTCs following the prompts on the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
Check the details of the DTCs.
Clear the DTCs.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Operate the intelligent tester to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / DTC / Clear.
DTC CHECK/CLEAR (When not Using the Intelligent Tester)
Check for DTCs.
Turn the engine switch off.
| *a | Front view of DLC3 |
Using SST, connect terminals TC and CG of the DLC3.
Turn the engine switch on (IG).
Observe the blinking pattern of the ABS warning and slip indicator lights in order to identify the DTC.
If no code appears, inspect the TC and CG terminal circuit, and ABS warning and slip indicator light circuits.
Count the number of blinks of the ABS warning and slip indicator lights.
How to read DTCs:
Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
If one code is detected:
The light repeats the same code after a pause of 4 seconds.
If multiple codes are detected:
The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.
Check the details of the DTCs.
| ABS Warning Light Display | Tester Display |
|---|---|
| 11 | C146E |
| 13 | C146C |
| 21 | C1468 |
| 22 | C1469 |
| 23 | C146A |
| 24 | C146B |
| 25 | C1225 |
| 26 | C1226 |
| 27 | C1227 |
| 28 | C1228 |
| 31 | C1464 |
| 32 | C1465 |
| 33 | C1466 |
| 34 | C1467 |
| 35 | C1330 |
| 36 | C1331 |
| 37 | C1237 |
| 38 | C1332 |
| 39 | C1333 |
| 41 | C1241 |
| C1417 | |
| 46 | C1246 |
| 49 | C1249 |
| C1425 | |
| C1426 | |
| 51 | C1428 |
| 62 | C1300 |
| 67 | C1429 |
| C1430 | |
| C1431 | |
| 94 | U0073 |
| Slip Indicator Light Display | Tester Display |
|---|---|
| 28 | C1472 |
| 31 | C1432 |
| C1433 | |
| C1434 | |
| C1439 | |
| C1445 | |
| 32 | C1419 |
| C1420 | |
| 34 | C1234 |
| C1435 | |
| C1436 | |
| 43*1 | - |
| 44 | C1224 |
| 51 | C1201 |
| 62 | U0123 |
| 63 | U0126 |
| 65 | U0100 |
| 6A*2 | C1381 |
| 88 | C1288 |
| - | C1441 |
*1: This DTC is output when the VSC system detects a malfunction in the ABS.
*2: The light blinks 6 times, turns off for 1.5 seconds, and then blinks 10 times.
When the skid control ECU detects a brake booster failure, the brake warning light illuminates and the skid control ECU stores DTC C1441.
After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.
If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.
Clear the DTCs.
Turn the engine switch off.
| *a | Front view of DLC3 |
Using SST, connect terminals TC and CG of the DLC3.
Turn the engine switch on (IG).
Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.
Check that the warning light indicates a normal system code.
Remove SST from the terminals of the DLC3.
The DTCs cannot be cleared by disconnecting the battery terminal or the ECU-IG1 NO. 1 fuse.
END OF DTC CHECK/CLEAR
Turn the engine switch on (IG).
Check that the ABS warning and slip indicator lights go off within approximately 3 seconds after turning the engine switch on (IG).