Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074557 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and navigation receiver assembly*1 or radio and display receiver assembly*2 are not normal.

*1: w/ Navigation System

*2: w/o Navigation System


DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2



*1: w/ Navigation System

*2: w/o Navigation System


WIRING DIAGRAM

E288974E15
1.781,0.531 2.24,0.729 0.458,0.198 10 false CA+ 1.677,0.938 2.135,1.135 0.458,0.198 10 false CGND 2.167,0.438 2.479,0.635 0.313,0.198 10 false 11 2.167,0.844 2.479,1.042 0.313,0.198 10 false 23 0.979,1.323 1.438,1.521 0.458,0.198 10 false I178 0.979,1.49 3.063,1.823 2.083,0.333 10 false Navigation Receiver Assembly*1 3.573,0.792 3.885,0.99 0.313,0.198 10 false *3 5.146,0.438 5.302,0.635 0.156,0.198 10 false 6 5.146,0.833 5.302,1.031 0.156,0.198 10 false 5 5.354,0.542 5.813,0.74 0.458,0.198 10 false CB+ 5.354,0.938 5.813,1.135 0.458,0.198 10 false CGND 5.073,1.281 5.531,1.479 0.458,0.198 10 false T25 5.063,1.458 6.531,1.865 1.469,0.406 10 false Rear Television Camera Assembly 4.896,2.438 5.885,2.677 0.99,0.24 10 false *3: Shielded 0.969,2.031 3.594,2.365 2.625,0.333 10 false Radio and Display Receiver Assembly*2 0.833,2.438 3.458,2.792 2.625,0.354 10 false *1: w/ Navigation System 2.802,2.438 5.427,2.792 2.625,0.354 10 false *2: w/o Navigation System 0.979,1.875 1.438,2.073 0.458,0.198 10 false I179

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I178 navigation receiver assembly connector.


b.

Disconnect the T25 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I178-11 (CA+) - T25-6 (CB+) Always Below 1 Ω
I178-23 (CGND) - T25-5 (CGND) Always Below 1 Ω
I178-11 (CA+) - I178-23 (CGND) Always 10 kΩ or higher
I178-11 (CA+) - Body ground Always 10 kΩ or higher
I178-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (CA+)
a.

Reconnect the I178 navigation receiver assembly connector.


b.
E271917C73
1.521,0.188 1.969,0.479 0.448,0.292 0.833,0.708 1.219,1.125 false 1.615,0.25 2,0.438 0.385,0.188 10 false I178 0.531,0.583 1.156,0.813 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I178-11 (CA+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the I179 radio and display receiver assembly connector.


b.

Disconnect the T25 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I179-11 (CA+) - T25-6 (CB+) Always Below 1 Ω
I179-23 (CGND) - T25-5 (CGND) Always Below 1 Ω
I179-11 (CA+) - I179-23 (CGND) Always 10 kΩ or higher
I179-11 (CA+) - Body ground Always 10 kΩ or higher
I179-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (CA+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (CA+)
a.

Reconnect the I179 radio and display receiver assembly connector.


b.
E271917C74
1.521,0.188 1.969,0.479 0.448,0.292 0.813,0.771 1.229,1.125 false 1.615,0.25 2,0.438 0.385,0.188 10 false I179 0.5,0.646 1.125,0.875 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I179-11 (CA+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY