Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0074736 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights via the engine room junction block assembly.

WIRING DIAGRAM

E317748E01
0.375,0.896 1.26,1.135 0.885,0.24 10 false from Battery 2.219,1.083 2.635,1.302 0.417,0.219 10 false ALT 2.521,1.698 3.635,1.958 1.115,0.26 10 false from ALT Fuse 2.531,2.958 3.417,3.198 0.885,0.24 10 false from Battery 1.865,4.615 2.156,4.833 0.292,0.219 10 false A6 1.865,4.771 3.458,5.01 1.594,0.24 10 false Fog Light Assembly LH 1.844,5.615 2.135,5.833 0.292,0.219 10 false A57 1.844,5.771 3.438,6.01 1.594,0.24 10 false Fog Light Assembly RH 0.073,5.75 1.479,6.135 1.406,0.385 10 false Engine Room Junction Block Assembly 5.396,4.375 7.063,4.781 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.396,4.208 5.688,4.427 0.292,0.219 10 false MB 3.813,2.917 5.427,3.302 1.615,0.385 10 false Instrument Panel Junction Block Assembly 0.823,2.146 1.24,2.365 0.417,0.219 10 false TAIL 0.844,1.698 1.26,1.917 0.417,0.219 10 false ALT 0.719,2.542 1.135,2.76 0.417,0.219 10 false FOGS 0.76,2.979 1.177,3.198 0.417,0.219 10 false BATT 0.74,3.406 1.156,3.625 0.417,0.219 10 false GND1 0.76,3.823 1.177,4.042 0.417,0.219 10 false GND2 0.76,4.427 1.177,4.646 0.417,0.219 10 false FOGL 0.719,5.396 1.135,5.615 0.417,0.219 10 false FOGR 1.375,1.698 1.615,1.885 0.24,0.188 10 false B 1.333,2.146 1.573,2.333 0.24,0.188 10 false 1G 1.344,2.552 1.583,2.74 0.24,0.188 10 false 1F 1.375,2.969 1.615,3.156 0.24,0.188 10 false A 1.344,3.396 1.583,3.583 0.24,0.188 10 false 1F 1.323,3.823 1.563,4.01 0.24,0.188 10 false 1G 1.344,4.427 1.583,4.615 0.24,0.188 10 false 1F 1.333,5.417 1.573,5.604 0.24,0.188 10 false 1F 3.948,0.917 4.188,1.104 0.24,0.188 10 false 3E 3.958,1.583 4.198,1.771 0.24,0.188 10 false 3F 3.958,2.135 4.198,2.323 0.24,0.188 10 false 3D 3.948,2.552 4.188,2.74 0.24,0.188 10 false 3D 5.99,0.906 6.406,1.125 0.417,0.219 10 false TRLY 6,2.531 6.51,2.76 0.51,0.229 10 false FFGO 4.948,1.427 5.365,1.646 0.417,0.219 10 false TAIL 4.948,2.302 5.365,2.521 0.417,0.219 10 false TAIL 5.74,0.792 6.01,1.01 0.271,0.219 10 false 14 5.74,2.427 6.01,2.646 0.271,0.219 10 false 13 3.979,0.719 4.25,0.938 0.271,0.219 10 false 1 3.99,1.375 4.26,1.594 0.271,0.219 10 false 1 4,1.938 4.271,2.156 0.271,0.219 10 false 9 3.948,2.365 4.219,2.583 0.271,0.219 10 false 38 3.958,1.792 4.229,2.01 0.271,0.219 10 false *2 3.958,1.125 4.229,1.344 0.271,0.219 10 false *1 1.375,1.5 1.646,1.719 0.271,0.219 10 false 1 1.396,1.948 1.667,2.167 0.271,0.219 10 false 2 1.344,2.354 1.615,2.573 0.271,0.219 10 false 13 1.375,2.771 1.646,2.99 0.271,0.219 10 false 1 1.385,3.208 1.656,3.427 0.271,0.219 10 false 3 1.385,3.646 1.656,3.865 0.271,0.219 10 false 4 1.385,4.229 1.656,4.448 0.271,0.219 10 false 2 1.365,5.208 1.635,5.427 0.271,0.219 10 false 1 2.292,4.438 2.531,4.625 0.24,0.188 10 false B 2.74,4.448 2.979,4.635 0.24,0.188 10 false E 2.292,5.417 2.531,5.604 0.24,0.188 10 false B 2.74,5.417 2.979,5.604 0.24,0.188 10 false E 4.469,5.76 5.552,5.979 1.083,0.219 10 false *1: for LHD 4.469,6.177 5.552,6.396 1.083,0.219 10 false *2: for RHD 2.094,4.323 2.365,4.542 0.271,0.219 10 false 2 2.927,4.333 3.198,4.552 0.271,0.219 10 false 1 2.104,5.302 2.375,5.521 0.271,0.219 10 false 2 2.948,5.313 3.219,5.531 0.271,0.219 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Fog Light Relay Front fog light relay ON/OFF Make sure the light control switch is in the tail position
Body Electrical > Main Body > Active Test
Tester Display
Front Fog Light Relay
50004 123 16
OK:

Front fog light relay operates. (Front fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

E230000C11
2.781,2.615 3.094,2.813 0.313,0.198 4.729,2.708 5.042,2.906 0.313,0.198 6.188,3.094 6.5,3.292 0.313,0.198 0.771,3.073 1.083,3.271 0.313,0.198 5.104,3.656 5.271,3.979 false 0.865,3.583 0.792,3.896 false 2.615,3.688 2.552,4.135 false 6.281,3.625 6.219,3.948 false 2.865,2.635 3.271,2.896 0.406,0.26 10 1F 4.802,2.729 5.469,3.125 0.667,0.396 10 1G 6.302,3.115 6.75,3.438 0.448,0.323 10 A 0.875,3.094 1.406,3.469 0.531,0.375 10 B 0.271,0.208 0.688,0.552 0.417,0.344 10 *a 6.083,3.958 6.781,4.323 0.698,0.365 10 BATT 5.115,4 5.823,4.333 0.708,0.333 10 GND2 2.344,4.167 3.24,4.542 0.896,0.375 10 GND1 0.646,3.927 1.5,4.344 0.854,0.417 10 ALT
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Always 11 to 14 V
B-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-2 (TAIL) - 3D-9 Always Below 1 Ω
3D-9 - Body ground Always 10 kΩ or higher
1F-13 (FOGS) - 3D-38 Always Below 1 Ω
3D-38 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

E173042C11
1.396,0.406 1.75,0.625 0.354,0.219 4.5,0.406 4.854,0.625 0.354,0.219 3.417,2.313 3.771,2.531 0.354,0.219 2.01,0.406 2.365,0.625 0.354,0.219 3.177,3.042 2.99,3.427 false 3.302,3.042 3.5,3.427 false 0.427,0.271 0.625,0.427 0.198,0.156 10 *a 2.813,3.448 3.313,3.719 0.5,0.271 10 FFGO 3.365,3.448 4.031,3.656 0.667,0.208 10 TRLY 1.51,0.448 1.938,0.698 0.427,0.25 10 3E 4.604,0.448 5.042,0.677 0.438,0.229 10 3D 3.51,2.354 4.146,2.656 0.635,0.302 10 MB 1.823,0.448 2.25,0.698 0.427,0.25 10 *A 2.104,0.438 2.531,0.688 0.427,0.25 10 3F 2.417,0.448 2.844,0.698 0.427,0.25 10 *B
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-13 (FFGO) - 3D-38 Always Below 1 Ω
3D-38 - Body ground Always 10 kΩ or higher



d.

Connect a positive (+) lead from the battery to terminal 3E-1*1 or 3F-1*2.

*1: for LHD

*2: for RHD



e.

Connect a negative (-) lead from the battery to terminal MB-14.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-9 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Replace the engine room junction block assembly with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Check that the front fog lights operate normally.

OK:

The front fog lights operate normally.



Result:
Proceed to
OK
NG



OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)