Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2030EQ _57 Power Source / Network _014663 NETWORKING _0074573 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C240955E53
1.396,5.01 2.406,5.365 1.01,0.354 10 false Trouble Area 3.958,2.333 4.51,2.552 0.552,0.219 10 false DLC3 1.271,0.573 3.771,0.906 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.281,0.938 3.781,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.292,1.271 3.031,1.604 1.74,0.333 10 false : CAN Branch Line (CANH) 1.281,1.604 3.021,1.938 1.74,0.333 10 false : CAN Branch Line (CANL) 1.281,4.594 3.219,4.771 1.938,0.177 10 false Combination Meter Assembly 1.719,3.104 1.979,3.385 0.26,0.281 10 false B 1.698,3.656 2.021,3.906 0.323,0.25 10 false IG+ 1.708,4.271 2.104,4.5 0.396,0.229 10 false ES 1.052,4.594 1.427,4.792 0.375,0.198 10 false I18 2.406,3.958 2.854,4.24 0.448,0.281 10 false CANL 2.375,3.094 2.844,3.354 0.469,0.26 10 false CANH 2.292,4.188 2.74,4.427 0.448,0.24 10 false 120 Ω 6.156,3.979 6.646,4.24 0.49,0.26 10 false 120 Ω 1.458,4.156 1.813,4.406 0.354,0.25 10 false 20 2.854,3.094 3.083,3.344 0.229,0.25 10 false 17 2.865,3.958 3.135,4.208 0.271,0.25 10 false 16 0.75,3.271 1.646,3.531 0.896,0.26 10 false ECU-B NO. 1 0.76,3.823 1.615,4.125 0.854,0.302 10 false METER-IG2 1.5,3 1.677,3.24 0.177,0.24 10 false 1 1.458,3.542 1.708,3.75 0.25,0.208 10 false 13 3.698,4.594 4.365,5.302 0.667,0.708 10 false CAN No. 1 Junction Connector 4.771,4.604 5.448,5.302 0.677,0.698 10 false CAN No. 2 Junction Connector 6.344,4.594 6.76,4.854 0.417,0.26 10 false ECM 0.094,0.156 1.5,0.635 1.406,0.479 12 false V Bus (for LHD): 6.021,4.594 6.365,4.813 0.344,0.219 10 false A25

C240955E54
1.365,5.031 2.344,5.271 0.979,0.24 10 false Trouble Area 3.948,2.344 4.542,2.604 0.594,0.26 10 false DLC3 1.281,0.583 3.781,0.917 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.26,0.938 3.76,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.26,1.271 3,1.604 1.74,0.333 10 false : CAN Branch Line (CANH) 1.26,1.615 3,1.948 1.74,0.333 10 false : CAN Branch Line (CANL) 1.302,4.563 3.292,4.823 1.99,0.26 10 false Combination Meter Assembly 1.708,3.115 1.854,3.292 0.146,0.177 10 false B 1.698,3.656 1.979,3.844 0.281,0.188 10 false IG+ 1.698,4.198 1.99,4.375 0.292,0.177 10 false ES 1.073,4.563 1.458,4.76 0.385,0.198 10 false I18 2.375,3.958 2.771,4.146 0.396,0.188 10 false CANL 2.365,3.083 2.771,3.26 0.406,0.177 10 false CANH 2.292,4.177 2.781,4.479 0.49,0.302 10 false 120 Ω 6.135,4.042 6.656,4.302 0.521,0.26 10 false 120 Ω 1.469,4.167 1.854,4.375 0.385,0.208 10 false 20 2.833,3.083 3.073,3.302 0.24,0.219 10 false 17 2.844,3.969 3.094,4.25 0.25,0.281 10 false 16 0.719,3.281 1.573,3.458 0.854,0.177 10 false ECU-B NO. 1 0.76,3.823 1.542,4 0.781,0.177 10 false METER-IG2 1.51,3.01 1.688,3.26 0.177,0.25 10 false 1 1.469,3.573 1.677,3.75 0.208,0.177 10 false 13 3.698,4.594 4.375,5.229 0.677,0.635 10 false CAN No. 2 Junction Connector 4.781,4.594 5.469,5.208 0.688,0.615 10 false CAN No. 1 Junction Connector 6.281,4.583 6.719,4.844 0.438,0.26 10 false ECM 0.104,0.135 1.531,0.51 1.427,0.375 12 false V Bus (for RHD): 5.979,4.583 6.375,4.792 0.396,0.208 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the engine switch on (IG) and wait at least 52 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.
E224284C94
1.24,0.521 1.729,0.813 0.49,0.292 1.479,2.167 1.479,2.51 1.479,2.51 1.667,2.51 false 1.354,2.156 1.354,2.51 1.354,2.51 1.167,2.51 false 0.156,0.177 0.438,0.458 0.281,0.281 10 false *a 1.729,2.427 2.26,2.667 0.531,0.24 10 false CANH 0.75,2.427 1.281,2.667 0.531,0.24 10 false CANL 1.375,0.594 1.656,0.771 0.281,0.177 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-17 (CANH) - I18-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN LINE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E224284C95
1.427,0.677 1.854,0.938 0.427,0.26 0.979,2.156 0.979,2.531 0.979,2.531 1.219,2.531 false 0.948,1.958 0.667,1.958 false 1.854,2.135 1.979,2.573 1.979,2.573 2.156,2.573 true 0.167,0.115 0.646,0.469 0.479,0.354 10 false *a 1.563,0.74 2.042,1.052 0.479,0.313 10 false I18 0.531,1.896 0.906,2.167 0.375,0.271 10 false B 1.271,2.469 1.854,2.823 0.583,0.354 10 false IG+ 2.229,2.49 2.563,2.75 0.333,0.26 10 false ES
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-20 (ES) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-13 (IG+) - Body ground Engine switch on (IG) 11 to 14 V
I18-1 (B) - Body ground Engine switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)