This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit. | ·
Harness or connector ·
Speaker ·
Navigation receiver assembly*1 ·
Stereo component amplifier assembly*2 |
*1: for 6 Speakers
*2: for 10 Speakers
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 10 Speakers | B |
A
B
Disconnect the I64 and I65 navigation receiver assembly connectors.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Disconnect the O18 and O21 rear speaker assembly connectors.
Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I64-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I64-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I64-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I64-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| I65-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I65-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| I65-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I65-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I83-3 (+) - Body ground | Always | 10 kΩ or higher |
| I83-1 (-) - Body ground | Always | 10 kΩ or higher |
| I1-3 (+) - Body ground | Always | 10 kΩ or higher |
| I1-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (TWR+) - 2 (TWR-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWR+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWR-) | Always | Below 1 Ω |
| 4 (TWL+) - 2 (TWL-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWL+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWL-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Disconnect the I84 and I2 front No. 2 speaker assembly connectors.
Disconnect the I60 front No. 3 speaker assembly connector.
Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
Disconnect the O22 rear speaker assembly connector.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I68-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) - Body ground | Always | 10 kΩ or higher |
| I68-12 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I68-13 (CTR+) - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) - Body ground | Always | 10 kΩ or higher |
| I68-10 (SR+) - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) - Body ground | Always | 10 kΩ or higher |
| I68-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4.6 to 6.6 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 3 | Always | 3.4 to 5.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 3 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 1 | Always | 6.8 to 10.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 1 | Always | 6.8 to 10.2 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR PACKAGE TRAY SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4.8 to 6.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG