Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E262317E69
1.25,1.042 1.719,1.198 0.469,0.156 10 false MUTE 5.552,1.052 5.969,1.219 0.417,0.167 10 false MUT1 1.771,0.906 2.01,1.135 0.24,0.229 10 false 1 5.281,0.917 5.542,1.125 0.26,0.208 10 false 16 0.583,1.896 0.99,2.125 0.406,0.229 10 false I69 5.24,2.083 7.156,2.417 1.917,0.333 10 false Navigation Receiver Assembly 5.24,1.917 5.74,2.198 0.5,0.281 10 false I67 0.573,2.063 1.771,2.563 1.198,0.5 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C33
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 false 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.604,0.844 1.927,1.021 0.323,0.177 10 false I69 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I69-1 (MUTE) - Body ground Engine switch on (ACC)
Audio system playing
→ Audio system changing modes
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the I67 navigation receiver assembly connector.


b.

Disconnect the I69 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-16 (MUT1) - I69-1 (MUTE) Always Below 1 Ω
I67-16 (MUT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the I67 navigation receiver assembly connector.


b.
E265411C20
1.5,0.5 1.938,0.781 0.438,0.281 0.854,2.542 0.979,2.094 false 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.594,0.542 2.24,0.885 0.646,0.344 10 false I67 0.688,2.594 1.333,2.854 0.646,0.26 10 false MUT1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I67-16 (MUT1) - Body ground Engine switch on (ACC)
Audio system playing
2.0 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY