Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E276615E08
2.958,2.219 4.938,2.406 1.979,0.188 10 false : AVC-LAN Communication Line 0.771,1.427 1.229,1.625 0.458,0.198 10 false I69 5.094,0.594 5.552,0.792 0.458,0.198 10 false TX1+ 4.833,1.604 6.833,1.958 2,0.354 10 false Navigation Receiver Assembly 0.76,1.594 3.354,1.854 2.594,0.26 10 false Stereo Component Amplifier Assembly 4.833,1.448 5.292,1.646 0.458,0.198 10 false I67 5.094,0.979 5.552,1.177 0.458,0.198 10 false TX1- 4.917,0.448 5.115,0.625 0.198,0.177 10 false 7 4.917,0.833 5.115,1.01 0.198,0.177 10 false 8 1.854,0.573 2.313,0.771 0.458,0.198 10 false TX+ 1.875,0.969 2.115,1.177 0.24,0.208 10 false TX- 2.177,0.458 2.375,0.635 0.198,0.177 10 false 8 2.177,0.833 2.375,1.01 0.198,0.177 10 false 7

PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E221758C27
1.365,1.729 1.615,1.229 false 2.083,1.729 1.802,1.219 false 0.094,0.094 0.625,0.469 0.531,0.375 10 false *a 1.208,1.771 1.583,2.021 0.375,0.25 10 false TX1- 1.99,1.771 2.521,2 0.531,0.229 10 false TX1+
*a Component without harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the I67 navigation receiver assembly connector.


b.

Disconnect the I69 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-7 (TX1+) - I69-8 (TX+) Always Below 1 Ω
I67-8 (TX1-) - I69-7 (TX-) Always Below 1 Ω
I67-7 (TX1+) - Body ground Always 10 kΩ or higher
I67-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG