Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E316128E01
0.146,2.438 3.052,2.625 2.906,0.188 10 false Certification ECU (Smart Key ECU Assembly) 0.24,3.677 2.927,3.865 2.688,0.188 10 false Stereo Component Amplifier Assembly*4 0.365,4.906 2.771,5.146 2.406,0.24 10 false Windshield Wiper Relay Assembly*5 4.99,3.698 7.052,3.927 2.063,0.229 10 false Navigation Receiver Assembly*1 0.427,6.083 2.75,6.302 2.323,0.219 10 false Headlight Leveling ECU Assembly*6 4.625,4.917 7.104,5.146 2.479,0.229 10 false Radio and Display Receiver Assembly*2 5.156,6.094 6.885,6.313 1.729,0.219 10 false Radio Receiver Assembly*3 6.042,7.302 6.469,7.5 0.427,0.198 10 false ECM 5.198,2.51 7.052,2.719 1.854,0.208 10 false Combination Meter Assembly 0.479,1.281 3.313,1.49 2.833,0.208 10 false Brake Actuator Assembly (Skid Control ECU) 2.823,5.135 4.094,5.333 1.271,0.198 10 false Junction Connector 1.344,7.323 1.75,7.531 0.406,0.208 10 false TCM 0.344,7.927 2.313,8.156 1.969,0.229 10 false *1: for Navigation Receiver Type 2.656,7.917 4.625,8.146 1.969,0.229 10 false *2: for Radio and Display Type 4.865,7.927 6.833,8.156 1.969,0.229 10 false *3: for Radio Receiver Type 0.344,8.333 2.313,8.563 1.969,0.229 10 false *4: for 10 Speakers 1.792,8.344 3.542,8.583 1.75,0.24 10 false *5: w/ Auto Wiper System 3.635,8.333 7.073,8.573 3.438,0.24 10 false *6: w/ Automatic Headlight Beam Level Control System 0.156,1.292 0.49,1.5 0.333,0.208 10 false A49 0.167,2.26 0.5,2.469 0.333,0.208 10 false I78 0.25,3.51 0.583,3.719 0.333,0.208 10 false I69 0.365,4.74 0.698,4.948 0.333,0.208 10 false I72 0.427,5.927 0.76,6.135 0.333,0.208 10 false A78 1.083,7.323 1.333,7.531 0.25,0.208 10 false E7 5.719,7.302 6.052,7.51 0.333,0.208 10 false A25 5.156,5.917 5.573,6.125 0.417,0.208 10 false I150 4.635,4.75 5.052,4.958 0.417,0.208 10 false I155 4.99,3.521 5.406,3.729 0.417,0.208 10 false I67 5.198,2.344 5.615,2.552 0.417,0.208 10 false I18 1.708,1.99 2.042,2.198 0.333,0.208 10 false SPD 1.698,3.25 2.031,3.458 0.333,0.208 10 false SPD 1.688,4.458 2.021,4.667 0.333,0.208 10 false SPD 1.615,5.635 2.052,5.833 0.438,0.198 10 false SPDR 1.708,6.854 2.063,7.021 0.354,0.167 10 false SPD 5.594,6.854 5.948,7.021 0.354,0.167 10 false SPD 5.594,5.635 5.948,5.802 0.354,0.167 10 false SPD 5.594,4.458 5.948,4.625 0.354,0.167 10 false SPD 5.594,3.24 5.948,3.406 0.354,0.167 10 false SPD 0.854,0.396 1.188,0.604 0.333,0.208 10 false SP1 2.823,4.969 3.156,5.177 0.333,0.208 10 false I185 1.229,0.396 1.563,0.604 0.333,0.208 10 false 2 2.104,2 2.438,2.208 0.333,0.208 10 false 27 2.094,3.25 2.427,3.458 0.333,0.208 10 false 11 2.115,4.458 2.448,4.667 0.333,0.208 10 false 24 2.104,5.635 2.438,5.844 0.333,0.208 10 false 16 2.115,6.854 2.448,7.063 0.333,0.208 10 false 3 5.333,6.844 5.5,7.094 0.167,0.25 10 false 10 5.323,5.635 5.49,5.802 0.167,0.167 10 false 17 5.313,4.458 5.479,4.625 0.167,0.167 10 false 17 5.323,3.24 5.49,3.406 0.167,0.167 10 false 17 5.385,0.406 5.552,0.615 0.167,0.208 10 false 4 5.375,1.99 5.542,2.198 0.167,0.208 10 false 3 5.604,2.073 5.854,2.281 0.25,0.208 10 false +S 5.615,0.479 5.865,0.688 0.25,0.208 10 false SI 3.948,1.99 4.115,2.198 0.167,0.208 10 false 18 2.906,1.99 3.073,2.198 0.167,0.208 10 false 15 2.906,3.25 3.073,3.458 0.167,0.208 10 false 19 3.958,3.25 4.125,3.458 0.167,0.208 10 false 17 2.917,4.438 3.083,4.646 0.167,0.208 10 false 20 3.938,4.448 4.104,4.656 0.167,0.208 10 false 16

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.
E286967C23
1.5,0.333 1.917,0.583 0.417,0.25 2.135,1.354 2.667,0.667 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.604,0.365 2.063,0.563 0.458,0.198 10 false I18 2.667,0.5 3.125,0.698 0.458,0.198 10 false +S 1.115,3.844 1.427,4.042 0.313,0.198 10 false A 2.781,3.594 3.24,3.792 0.458,0.198 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Connect an oscilloscope to terminal I18-3 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-3 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.
E286967C25
1.5,0.333 1.917,0.583 0.417,0.25 1.156,1.365 0.76,0.771 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.594,0.375 2.052,0.573 0.458,0.198 10 false I69 0.51,0.604 0.969,0.802 0.458,0.198 10 false SPD 1.115,3.844 1.427,4.042 0.313,0.198 10 false A 2.781,3.594 3.24,3.792 0.458,0.198 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Connect an oscilloscope to terminal I69-11 (SPD) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I69-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I69 stereo component amplifier assembly connector.


b.

Disconnect the I185 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-11 (SPD) - I185-19 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the I185 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (+S) - I185-18 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR