Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.04
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM L

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  PRECAUTION  


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected:


System See Procedure
Parking Assist Monitor System (Click here)


TROUBLESHOOTING PRECAUTIONS


a.

When there is a malfunction with terminal contact points or part installation problems, removal and installation of the suspected parts may return the system to normal either completely or temporarily.


b.

In order to determine the malfunctioning area, be sure to check the conditions at the time the malfunction occurred, such as DTC output and the Freeze Frame Data, and record it before disconnecting any connector or removing and installing parts.


c.

Since the system may be influenced by malfunctions in systems other than the VSC system, be sure to check for DTCs in other systems.



HANDLING PRECAUTIONS


a.

Do not remove or install VSC parts such as the steering angle sensor or yaw rate and acceleration sensor (airbag sensor assembly) except when required, as they need to be adjusted correctly after removal and installation.


b.

Be sure to perform preparation before work and confirmation after work is completed by following the directions in the repair manual when working on the VSC system.


c.

Be sure to remove and install the ECU, brake actuator assembly, sensors, etc. with the engine switch off unless it is otherwise specified in the inspection procedure.


d.

If the ECU, brake actuator assembly or a sensor has been removed and installed, it is necessary to check the system for problems after the parts have been reassembled. Check for DTCs using the intelligent tester, also check that system functions and signals received by the ECU are normal using Test Mode.



DTC PRECAUTION


a.

Warnings for some DTCs cannot be cleared only by repairing the malfunctioning parts. If the warning is displayed after repair work, the DTC should be cleared after turning the engine switch off.

NOTICE:

If a DTC for a malfunctioning part reappears after it was cleared, then it has been stored again.



b.

When 2 or more DTCs are detected, perform diagnosis for each DTC, one by one until the problem is identified.



CHASSIS DYNAMOMETER PRECAUTION


When testing with a 2-wheel drum tester such as a speedometer tester, a combination tester for the speedometer and brakes, a chassis dynamometer, or when jacking up the front wheels and turning the wheels, perform the following procedure to enter Inspection Mode and stop the TRC and VSC systems.

Enter Inspection Mode to disable TRC and VSC operation when using a chassis dynamometer.

HINT:
·

If Inspection Mode is not used, the vehicle may unexpectedly move off the dynamometer because of TRC and VSC operation.

·

The vehicle stability control switch must not be used to disable TRC and VSC operation when the vehicle is to be operated on a dynamometer. Pressing the vehicle stability control switch does not disable TRC and VSC operation completely.



NOTICE:

Secure the vehicle with lock chains for safety.


a.

Activating Inspection Mode (When Using the intelligent tester)

i.

Ensure that the engine switch is off and the engine is stopped.


ii.

Make sure that the shift lever is in P.


iii.

Connect the intelligent tester to the DLC3.


iv.

Start the engine.


v.

Turn the intelligent tester on.


vi.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Inspection Mode.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Inspection Mode
50005 105 179

vii.

Check that the VSC OFF indicator light comes on and the TRC OFF message will be displayed on the multi-information display.

HINT:
·

If the VSC OFF indicator light does not come on and the TRC OFF message is not displayed on the multi-information display, repeat the steps above.

·

Turning the engine switch off ends Inspection Mode.





b.

Activating Inspection Mode (When not Using the intelligent tester)

HINT:

Perform steps "C" to "H" within 30 seconds.


i.

Ensure that the engine switch is off and the engine is stopped (Step "A").


ii.

Make sure that the shift lever is in P (Step "B").


iii.

Start the engine (Step "C").


iv.

Apply the parking brake by depressing the parking brake pedal (Step "D").


v.

Depress and release the brake pedal twice (Step "E").


vi.

While holding the brake pedal down, release and apply the parking brake twice (Step "F").


vii.

With the parking brake applied, depress and release the brake pedal twice (Step "G").


viii.

Check that the VSC OFF indicator light comes on and the TRC OFF message is displayed on the multi-information display (Step "H").

HINT:
·

If the VSC OFF indicator light does not come on and the TRC OFF message is not displayed on the multi-information display in step "H", repeat steps "A" to "H".

·

Turning the engine switch off ends Inspection Mode.






CAN COMMUNICATION SYSTEM PRECAUTIONS


a.

The CAN communication system is used for communication between the skid control ECU (brake actuator assembly), the steering angle sensor, the yaw rate and acceleration sensor (airbag sensor assembly) and other ECUs. If any CAN communication DTCs are detected, DTCs corresponding to the malfunction will be output.


b.

If any CAN communication DTCs are output, repair the malfunction and troubleshoot the VSC system while communication is normal.


c.

In order to enable CAN communication, a specific type of wiring is used for the CAN communication lines. The wiring used for each communication line is a twisted pair of wires that have an equal length. A bypass wire should not be used because the data being transmitted will be corrupted.