Home › General › INTRODUCTION › REPAIR INSTRUCTION › 2015.04–2016.05
RM2030EQ _V1 General _014630 INTRODUCTION _0074290 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED


Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed See page
Correct the steering angle neutral point Parking assist monitor system (Click here)

NOTICE:
·

After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 80 seconds*1 or 90 seconds*2 before disconnecting the cable from the negative (-) battery terminal. (for Radio and Display Type)

·

After the engine switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds*1 or 90 seconds*2 before disconnecting the cable from the negative (-) battery terminal. (for Navigation Receiver Type)

*1: for LHD

*2: for RHD





PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed See page
ECM Perform Vehicle Identification Number (VIN) or frame number registration
·

MIL illuminates

·

DTCs are output


(Click here)
Code registration (Engine immobiliser system) Engine start See the Service Bulletin for the registration method.
·

Throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft

(for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Lane departure warning camera Lane departure warning camera Lane departure warning camera (Click here)
Automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into TCM

3.

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for Initialization
(Click here)for Registration
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


1.

Reset memory

2.

Reset transaxle compensation code

3.

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Shift solenoid valve SL1 and/or SL2 Perform road test to allow TCM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


TCM (If possible, read the transaxle compensation code from the previous TCM) Possible
1.

Reset memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
1.

Reset memory

2.

Reset transaxle compensation code

3.

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Skid control ECU (Brake actuator assembly) Perform system variant learning
·

Slip indicator light illumination

·

VSC disabled or malfunctioning


(Click here)
Power steering ECU assembly Assist map writing
·

P/S warning light comes on

·

EPS control


(Click here)
·

Spiral cable sub-assembly

·

Spiral cable with sensor sub-assembly

·

Steering sensor


·

Steering angle neutral point (Initialize parking assist monitor system)

·

Steering angle setting


Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting)
Rear television camera assembly
·

Parking assist monitor system initialization

·

Rear television camera assembly optical axis (Back camera position setting)


Blind spot monitor sensor Blind spot monitor beam axis inspection DTCs are output (Click here)
·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator assembly)

·

Electrical key transmitter (key)


Code registration (Engine immobiliser system)
·

Wireless door lock control system

·

Smart entry and start system

·

Engine start

·

Steering lock system


See the Service Bulletin for the registration method.
·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

No. 1 blower damper servo sub-assembly


Initialization servo motor (Air conditioning system) DTCs are output (Click here)
·

Door window regulator assembly

·

Power window regulator motor assembly (for driver door)

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up/down function

·

Jam protection function

·

Operation function after ignition switch is turned off

·

Key-linked function*

·

Wireless transmitter-linked function*


(Click here)
·

Sliding roof ECU (sliding roof drive gear sub-assembly)

·

Sliding roof glass sub-assembly

·

Sliding roof drive cable sub-assembly


Initialize sliding roof ECU (pulse sensor initial position setting)
·

Automatic slide open/close and tilt up/down function of sliding roof

·

Jam protection function

·

Operation function after ignition switch is turned off

·

Key-linked function*

·

Wireless transmitter-linked function*

·

Sliding roof open warning


(Click here)
·

Headlight leveling ECU assembly

·

Rear height control sensor sub-assembly


Perform headlight leveling ECU initialization Automatic headlight beam level control function (Click here)


*: for RHD