Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.04
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM

WIRING DIAGRAM

C239015E24
5.49,4.031 7.031,4.469 1.542,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 5.49,3.885 5.906,4.104 0.417,0.219 10 false A49 0.281,4.031 1.563,4.375 1.281,0.344 10 false Combination Meter Assembly 0.281,3.885 0.594,4.042 0.313,0.156 10 false I18 5.969,1.146 6.521,1.448 0.552,0.302 10 false CANL 5.969,3.146 6.521,3.344 0.552,0.198 10 false CANH 5.698,1.01 6.01,1.354 0.313,0.344 10 false 14 5.698,3.031 6.073,3.25 0.375,0.219 10 false 26 0.885,1.125 1.333,1.281 0.448,0.156 10 false CANL 0.885,3.156 1.5,3.438 0.615,0.281 10 false CANH 1.396,1.01 2.063,1.344 0.667,0.333 10 false 16 1.396,3.01 1.813,3.219 0.417,0.208 10 false 17

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform an Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Slip
50004 122 16

b.

Check the combination meter assembly.

OK:

The slip indicator light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY