Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074560 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB0 Short to +B in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.


·

Outer mirror RH

·

Mirror sub-assembly RH

·

Wire harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E314323E14
1.604,1.26 1.76,1.458 0.156,0.198 10 false 1 1.604,1.74 1.74,1.896 0.135,0.156 10 false 2 1.302,1.365 1.458,1.563 0.156,0.198 10 false + 1.313,1.823 1.469,2.021 0.156,0.198 10 false - 0.271,2.188 0.885,2.385 0.615,0.198 10 false IND1 0.281,2.344 2.573,2.542 2.292,0.198 10 false Outer Mirror RH 0.26,2.646 2.427,3.031 2.167,0.385 10 false (Outer Rear View Mirror Indicator RH) 2.885,1.354 3.344,1.552 0.458,0.198 10 false z6 2.917,1.604 3.208,1.823 0.292,0.219 10 false 12 2.885,1.833 3.344,2.031 0.458,0.198 10 false z6 5.76,1.208 6.219,1.406 0.458,0.198 10 false 4 4.573,1.135 4.792,1.438 0.219,0.302 10 false 10 2.958,1.135 3.156,1.354 0.198,0.219 10 false 7 4.521,1.354 4.979,1.552 0.458,0.198 10 false J13 4.094,1.833 4.552,2.031 0.458,0.198 10 false GND 4.615,1.635 5.073,1.833 0.458,0.198 10 false 7 5.969,1.354 6.427,1.552 0.458,0.198 10 false OMIR 5.927,3.573 7.115,3.969 1.188,0.396 10 false Blind Spot Monitor Sensor RH 4,1.365 4.458,1.563 0.458,0.198 10 false BDSR 0.177,3.448 2.521,3.698 2.344,0.25 10 false Mirror Sub-assembly RH 3.208,3.438 4.76,3.792 1.552,0.354 10 false Outer Mirror Control ECU Assembly RH 5.906,3.385 6.365,3.583 0.458,0.198 10 false O32 4.552,1.833 5.01,2.031 0.458,0.198 10 false J13 3.271,1.354 3.729,1.552 0.458,0.198 10 false BDIR 3.292,1.823 3.75,2.021 0.458,0.198 10 false HTR-

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
2.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the O32 blind spot monitor sensor RH connector.


b.
E233763C12
1.479,0.49 2,0.802 0.521,0.313 1.896,1.625 2.438,0.833 false 2.438,0.833 2.646,0.833 false 0.094,0.094 0.302,0.292 0.208,0.198 10 false *a 2.667,0.74 3.115,0.927 0.448,0.188 10 false OMIR 1.615,0.563 1.958,0.771 0.344,0.208 10 false O32
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O32-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the IND1 outer mirror RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O32-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the z6 outer mirror control ECU assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O32-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MIRROR SUB-ASSEMBLY RH

NG

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR CIRCUIT)
a.

Disconnect the J13 outer mirror control ECU assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O32-4 (OMIR) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR