Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074560 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB5 Open in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

Blind spot monitor main switch (warning canceling switch assembly) is on.


·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.


·

Outer mirror LH

·

Mirror sub-assembly LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E314323E15
1.604,1.26 1.76,1.458 0.156,0.198 10 false 1 1.604,1.74 1.74,1.896 0.135,0.156 10 false 2 1.302,1.365 1.458,1.563 0.156,0.198 10 false + 1.313,1.823 1.469,2.021 0.156,0.198 10 false - 0.271,2.188 0.885,2.385 0.615,0.198 10 false IND2 0.271,2.365 2.563,2.563 2.292,0.198 10 false Outer Mirror LH 0.26,2.646 2.427,3.031 2.167,0.385 10 false (Outer Rear View Mirror Indicator LH) 2.885,1.354 3.344,1.552 0.458,0.198 10 false z5 2.917,1.615 3.156,1.823 0.24,0.208 10 false 12 2.885,1.833 3.344,2.031 0.458,0.198 10 false z5 5.76,1.208 6.219,1.406 0.458,0.198 10 false 4 4.563,1.146 4.823,1.354 0.26,0.208 10 false 10 2.958,1.156 3.115,1.354 0.156,0.198 10 false 7 4.521,1.354 4.979,1.552 0.458,0.198 10 false K12 4.094,1.833 4.552,2.031 0.458,0.198 10 false GND 4.615,1.635 5.073,1.833 0.458,0.198 10 false 7 5.969,1.354 6.427,1.552 0.458,0.198 10 false OMIL 5.906,3.542 7.094,3.938 1.188,0.396 10 false Blind Spot Monitor Sensor LH 4,1.365 4.458,1.563 0.458,0.198 10 false BDSL 0.177,3.448 2.521,3.698 2.344,0.25 10 false Mirror Sub-assembly LH 3.198,3.417 4.75,3.771 1.552,0.354 10 false Outer Mirror Control ECU Assembly LH 5.906,3.385 6.365,3.583 0.458,0.198 10 false T24 4.552,1.833 5.01,2.031 0.458,0.198 10 false K12 3.271,1.354 3.729,1.552 0.458,0.198 10 false BDIL 3.292,1.823 3.75,2.021 0.458,0.198 10 false HTR-

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH, BODY GROUND - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH, BODY GROUND - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.

Disconnect the T24 blind spot monitor sensor LH connector.


b.

Disconnect the K12 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T24-4 (OMIL) - K12-10 (BDSL) Always Below 1 Ω
K12-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Disconnect the z5 outer mirror control ECU assembly LH connector.


b.
E233744C71
2.219,0.208 2.646,0.469 0.427,0.26 0.844,0.208 1.271,0.469 0.427,0.26 2.552,1.26 2.76,1.708 false 2.052,1.073 2.208,1.698 false 1.146,1.26 1.344,1.698 false 0.708,1.073 0.615,1.677 false 2.313,0.25 2.594,0.406 0.281,0.156 10 false K12 2.604,1.719 3.083,1.917 0.479,0.198 10 false BDSL 0.094,0.031 0.292,0.229 0.198,0.198 10 false *a 0.927,0.26 1.177,0.417 0.25,0.156 10 false z5 2.063,1.719 2.458,1.917 0.396,0.198 10 false GND 1.208,1.719 1.688,1.917 0.479,0.198 10 false HTR- 0.375,1.719 0.875,1.917 0.5,0.198 10 false BDIL
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-10 (BDSL) - z5-7 (BDIL) Always Below 1 Ω
K12-7 (GND) - z5-12 (HTR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MIRROR SUB-ASSEMBLY LH - OUTER MIRROR LH)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (MIRROR SUB-ASSEMBLY LH - OUTER MIRROR LH)
a.

Disconnect the IND2 outer mirror LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-7 (BDIL) - IND2-1 (+) Always Below 1 Ω
z5-12 (HTR-) - IND2-2 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE OUTER MIRROR LH

NG

REPLACE MIRROR SUB-ASSEMBLY LH

5.REPLACE OUTER MIRROR LH
a.

Result:
Proceed to
NEXT



NEXT

6.RECHECK DTC
6.RECHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR LH WAS DEFECTIVE)

NG