Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0074560 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH judges that there is a communication problem with the blind spot monitor sensor LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0232 Lost Communication with Blind Spot Monitor Slave Module The blind spot monitor sensor RH cannot receive signals from the blind spot monitor sensor LH.
·

CAN communication Line

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E233765E41
3.042,1.208 3.354,1.385 0.313,0.177 10 false BLB 2.885,1.094 3,1.271 0.115,0.177 10 false 5 2.813,2.49 2.99,2.667 0.177,0.177 10 false 10 3.042,2.604 3.469,2.76 0.427,0.156 10 false BLGD 1.5,1.344 2.49,1.51 0.99,0.167 10 false ECU-IG1 NO. 3 0.104,1.177 1.083,1.5 0.979,0.323 10 false from IG1 NO. 3 Relay 3.031,3.198 3.396,3.354 0.365,0.156 10 false T24 3.031,3.375 4.646,3.719 1.615,0.344 10 false Blind Spot Monitor Sensor LH 5.417,3.198 5.781,3.354 0.365,0.156 10 false O32 5.417,3.375 7.031,3.719 1.615,0.344 10 false Blind Spot Monitor Sensor RH 3.531,1.573 3.927,1.75 0.396,0.177 10 false CA2P 3.531,1.917 3.927,2.094 0.396,0.177 10 false CA2N 4,1.448 4.115,1.625 0.115,0.177 10 false 1 4,1.781 4.115,1.958 0.115,0.177 10 false 6 5.24,1.448 5.354,1.625 0.115,0.177 10 false 1 5.26,1.802 5.375,1.979 0.115,0.177 10 false 6 5.385,1.563 5.781,1.74 0.396,0.177 10 false CA2P 5.385,1.917 5.781,2.094 0.396,0.177 10 false CA2N 0.875,4.01 3.156,4.188 2.281,0.177 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the T24 blind spot monitor sensor LH connector.


b.

Disconnect the O32 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T24-1 (CA2P) - O32-1 (CA2P) Always Below 1 Ω
T24-6 (CA2N) - O32-6 (CA2N) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T24-5 (BLB) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T24-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE BLIND SPOT MONITOR SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE BLIND SPOT MONITOR SENSOR LH

Result:
Proceed to
NEXT



NEXT

5.RECHECK DTC
5.RECHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG