Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.04
RM2030EQ _55 Steering _014656 STEERING COLUMN _0077044 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU is determined to be abnormal.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2782 Power Source Control ECU Malfunction Either condition is met (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


HINT:

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.


·

Steering lock ECU (Steering lock actuator assembly)

·

Certification ECU (Smart key ECU assembly)

·

Harness or connector


Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the key.)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2782 - -

WIRING DIAGRAM

C277550E26
1.26,0.448 1.573,0.646 0.313,0.198 10 false 17 5.167,0.479 5.479,0.677 0.313,0.198 10 false 5 5.167,1.323 5.479,1.521 0.313,0.198 10 false 3 2.75,3.302 4.323,3.5 1.573,0.198 10 false LIN Communication Line 0.917,0.635 1.344,0.844 0.427,0.208 10 false LIN 5.167,2.104 5.479,2.302 0.313,0.198 10 false 1 5.333,0.625 5.76,0.833 0.427,0.208 10 false LIN 5.344,2.208 5.771,2.417 0.427,0.208 10 false GND 1.281,1.302 1.594,1.5 0.313,0.198 10 false 29 0.802,1.417 1.302,1.635 0.5,0.219 10 false SLR+ 5.354,1.427 5.781,1.635 0.427,0.208 10 false IGE 0.25,2.833 0.667,3 0.417,0.167 10 false I78 5.167,2.833 5.594,3.042 0.427,0.208 10 false I24 0.25,3 2.021,3.583 1.771,0.583 10 false Certification ECU (Smart key ECU Assembly) 5.167,3 7.021,3.542 1.854,0.542 10 false Steering Lock ECU (Steering Lock Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the I24 steering lock ECU connector.


c.
C157850C23
0.344,0.917 0.833,1.208 0.49,0.292 1.281,2.417 1.031,1.729 false 0.333,0.302 0.708,0.583 0.375,0.281 10 *a 0.51,0.99 1.156,1.417 0.646,0.427 10 I24 0.823,1.563 1.385,1.938 0.563,0.375 10 GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-1 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the I24 steering lock ECU connector.


e.

Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.


f.
C241547C16
0.25,0.667 0.594,0.948 0.344,0.281 0.354,2.896 1.729,3.063 1.375,0.167 2.313,2.958 2.719,3.073 0.406,0.115 1.563,4.031 2.521,4.198 0.958,0.167 2.302,1.104 2.823,1.917 false 1.573,2.896 2.896,2.625 2.896,2.625 2.635,2.958 false 2.115,4.198 2.115,4.458 false 1.854,1.104 1.083,1.917 false 0.219,0.208 0.542,0.438 0.323,0.229 10 *a 2.927,2.521 3.104,2.708 0.177,0.188 10 *b 2.042,4.469 2.344,4.667 0.302,0.198 10 *c 0.313,0.729 0.833,1.177 0.521,0.448 10 I24 0.938,1.948 1.458,2.208 0.521,0.26 10 IGE 2.708,1.958 3.25,2.417 0.542,0.458 10 GND 2.958,4.063 3.427,4.427 0.469,0.365 10 GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection I24-3 (IGE) - I24-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating


HINT:
·

When taking measurements while the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

NG

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
a.

Clear the DTCs.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.

CAUTION:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Perform the DTC output confirmation operation.


b.

Check if DTC B2782 is output.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2782 is not output. A
DTC B2782 is output. B



A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

B

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the I24 steering lock ECU connector.


c.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


d.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-3 (IGE) - I78-29 (SLR+) Always Below 1 Ω
I24-3 (IGE) - Body ground Always 10 kΩ or higher
I78-29 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR