Home › Engine / Hybrid System › 2GR-FE COOLING › COOLING FAN SYSTEM › from 2015.04
RM2030EQ _51 Engine / Hybrid System _014639 2GR-FE COOLING _0074440 COOLING FAN SYSTEM J

2GR-FE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fans. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Electric Cooling Fan.

Powertrain > Engine > Active Test
Tester Display
Control the Electric Cooling Fan
50004 234 16

e.

Check the operation of the cooling fans while operating them using the tester.


OK:
Tester Operation Specified Condition
ON Cooling fans operating
OFF Cooling fans stopped


Result:
Result Proceed to
OK A
NG (Cooling fans do not operate) B
NG (Cooling fans do not stop) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO.2 COOLING FAN MOTOR)

C

15.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
2.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO.2 COOLING FAN MOTOR)
a.

Inspect the cooling fan motor and No. 2 cooling fan motor.

Click hereEngine / Hybrid System>2GR-FE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (Cooling fan motor) B
NG (No. 2 cooling fan motor) C



A

3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)

B

C

REPLACE NO.2 COOLING FAN MOTOR

3.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU POWER SOURCE)
a.
A254660C03
0.573,1.146 0.875,1.406 0.302,0.26 1.083,1.833 1.344,1.323 false 2.063,1.313 2.333,1.833 false 0.604,1.188 1.063,1.385 0.458,0.198 10 false A10 0.125,0.156 0.583,0.354 0.458,0.198 10 false *a 0.969,1.854 1.427,2.052 0.458,0.198 10 false E1 2.302,1.854 2.76,2.052 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Cooling Fan ECU)


Disconnect the cooling fan ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A10-3 (+B1) - A10-1 (E1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

NG

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A25-5 (RFC) or A10-2 (SI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

5.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A10-1 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

6.INSPECT FAN RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - BODY GROUND)

6.INSPECT FAN RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)

NG

REPLACE FAN RELAY

7.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)
A259175C02
2.25,0.76 2.563,0.958 0.313,0.198 10 false *1 0.594,1.938 0.906,2.135 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 FAN Relay


a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN relay) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BATTERY)

8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN RELAY)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A10-3 (+B1) - 5 (FAN relay) Always Below 1 Ω
A10-3 (+B1) or 5 (FAN relay) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN ECU - FAN RELAY)

9.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (FAN relay) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BODY GROUND)

10.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the FAN relay from the engine room relay block and junction block assembly.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1(FAN relay) - 3D-36 Always Below 1 Ω
1(FAN relay) or 3D-36 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.2 RELAY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

A284396C07
5.125,1 5.385,1.177 0.26,0.177 5.167,1.833 5.427,2.01 0.26,0.177 4.771,2.24 5.031,2.417 0.26,0.177 4.948,2.906 5.208,3.083 0.26,0.177 4.948,3.25 5.208,3.427 0.26,0.177 1.656,0.969 1.969,1.167 0.313,0.198 10 false *1 5.167,1 5.479,1.198 0.313,0.198 10 false 3B 4.823,2.24 5.135,2.438 0.313,0.198 10 false 3D 5.208,1.833 5.521,2.031 0.313,0.198 10 false 3A 4.99,2.906 5.302,3.104 0.313,0.198 10 false 3E 5,3.25 5.313,3.448 0.313,0.198 10 false 3F 4.969,2.729 5.281,2.927 0.313,0.198 10 false *a 4.99,3.469 5.302,3.667 0.313,0.198 10 false *b
*1 Instrument Panel Junction Block Assembly - -
*a LHD *b RHD


Standard Resistance (LHD):
Tester Connection Condition Specified Condition
3E-1 - 3D-36 Battery voltage is not applied between terminals 3A-27 and 3B-7 10 kΩ or higher
3E-1 - 3D-36 Battery voltage is applied between terminals 3A-27 and 3B-7 Below 1 Ω


Standard Resistance (RHD):
Tester Connection Condition Specified Condition
3F-1 - 3D-36 Battery voltage is not applied between terminals 3A-27 and 3B-7 10 kΩ or higher
3F-1 - 3D-36 Battery voltage is applied between terminals 3A-27 and 3B-7 Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO.2 RELAY)

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE)
A258037C03
0.76,3.563 1.083,3.833 0.323,0.271 0.75,1.313 1.073,1.583 0.323,0.271 0.823,1.375 1.135,1.573 0.313,0.198 10 false 3E 0.844,3.625 1.156,3.823 0.313,0.198 10 false 3F 2.271,1.333 2.583,1.531 0.313,0.198 10 false *b 2.854,3.583 3.167,3.781 0.313,0.198 10 false *c 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b LHD
*c RHD


a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (LHD):
Tester Connection Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V


Standard Voltage (RHD):
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3B-7 - Body ground Always Below 1 Ω


Result:
Result
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3A-27 - I78-6 (IG1D) Always Below 1 Ω
3A-27 or I78-6 (IG1D) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

15.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A25-5 (RFC) - A10-2 (SI) Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - COOLING FAN ECU)

16.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the cooling fan motor connector.


A255683C14
0.656,1.198 1.01,1.458 0.354,0.26 0.74,1.25 1.198,1.448 0.458,0.198 10 false z14 0.167,0.167 0.625,0.365 0.458,0.198 10 false *a
*a Component without harness connected
(Cooling Fan Motor)


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
z14-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (NO.2 COOLING FAN MOTOR - BODY GROUND)

NG

17.CHECK HARNESS AND CONNECTOR (NO.2 COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the No. 2 cooling fan motor connector.


A255684C18
0.635,1.229 0.979,1.5 0.344,0.271 0.698,1.292 1.156,1.49 0.458,0.198 10 false z15 0.156,0.167 0.615,0.365 0.458,0.198 10 false *a
*a Component without harness connected
(No. 2 Cooling Fan Motor)


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
z15-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO.2 COOLING FAN MOTOR