Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2015.04–2016.05
RM2030EQ _58 Vehicle Interior _014671 SEAT BELT _0077141 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the courtesy light switch condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects rear seat belt state. The rear seat belt warning light on the clock assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

B293354E09
0.531,4.885 2.375,5.156 1.844,0.271 10 false Combination Meter Assembly 0.646,7.51 2.292,7.938 1.646,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 0.75,8.365 2.458,8.604 1.708,0.24 10 false : CAN Communication Line 3.406,7.26 5.688,7.542 2.281,0.281 10 false Rear Door Courtesy Light Switch RH 3.667,4.813 5.406,5.188 1.74,0.375 10 false Rear Seat Inner with Center Belt Assembly RH 3.667,3.052 5.396,3.417 1.729,0.365 10 false Rear Seat Inner with Center Belt Assembly LH 3.667,2.906 4,3.146 0.333,0.24 10 false N41 4.031,1.896 5.115,2.125 1.083,0.229 10 false Clock Assembly 5.625,1.146 6.198,1.521 0.573,0.375 10 false ECU-IG1 NO. 2 6.5,1 7.146,1.417 0.646,0.417 10 false IG1 NO. 2 Relay 4.031,1.729 4.323,1.948 0.292,0.219 10 false I170 3.406,7.125 3.708,7.323 0.302,0.198 10 false O16 0.646,7.354 0.938,7.604 0.292,0.25 10 false I13 1.938,2.667 2.427,2.906 0.49,0.24 10 false RLSB 1.917,3.875 2.385,4.115 0.469,0.24 10 false RCSB 1.917,4.406 2.396,4.625 0.479,0.219 10 false RRSB 2.521,3.667 2.667,3.885 0.146,0.219 10 false 5 2.531,4.188 2.698,4.458 0.167,0.271 10 false 6 3.479,3.656 3.604,3.906 0.125,0.25 10 false 1 5.521,3.656 5.656,3.927 0.135,0.271 10 false 2 3.583,2.563 3.708,2.771 0.125,0.208 10 false 1 5.406,2.563 5.542,2.792 0.135,0.229 10 false 2 3.479,4.177 3.625,4.438 0.146,0.26 10 false 1 3.385,3.865 3.677,4.115 0.292,0.25 10 false O30 2.479,3.875 2.76,4.146 0.281,0.271 10 false I18 2.531,2.458 2.708,2.698 0.177,0.24 10 false 10 2.479,2.667 2.75,2.927 0.271,0.26 10 false I18 1.896,1.438 2.365,1.74 0.469,0.302 10 false RRMT 3.583,1.333 3.75,1.563 0.167,0.229 10 false 5 2.49,1.229 2.719,1.5 0.229,0.271 10 false 3 2.479,1.427 2.74,1.708 0.26,0.281 10 false I17 1.896,1 2.406,1.281 0.51,0.281 10 false RCMT 3.583,0.896 3.76,1.177 0.177,0.281 10 false 6 5.417,0.896 5.542,1.094 0.125,0.198 10 false 8 2.49,0.802 2.729,1.052 0.24,0.25 10 false 2 2.479,1 2.771,1.25 0.292,0.25 10 false I17 1.917,0.573 2.354,0.792 0.438,0.219 10 false RLMT 3.781,1.438 4.271,1.656 0.49,0.219 10 false RRID 3.781,1 4.24,1.208 0.458,0.208 10 false RCID 5.052,1 5.375,1.24 0.323,0.24 10 false IG+ 3.802,0.573 4.24,0.833 0.438,0.26 10 false RLID 3.583,0.469 3.74,0.729 0.156,0.26 10 false 7 2.531,0.354 2.74,0.646 0.208,0.292 10 false 6 2.479,0.573 2.75,0.813 0.271,0.24 10 false I17 2.479,4.396 2.792,4.646 0.313,0.25 10 false I18 3.385,4.396 3.698,4.635 0.313,0.24 10 false O29 5.417,3.875 5.698,4.135 0.281,0.26 10 false O30 5.406,4.417 5.719,4.646 0.313,0.229 10 false O29 5.521,4.177 5.688,4.438 0.167,0.26 10 false 2 1.948,6.042 2.385,6.313 0.438,0.271 10 false LCTY 0.646,6.458 1.031,6.698 0.385,0.24 10 false CAN 0.646,2.49 1.052,2.76 0.406,0.271 10 false CAN 1.927,6.875 2.427,7.146 0.5,0.271 10 false RCTY 3.583,6.781 3.74,7.021 0.156,0.24 10 false 1 2.417,6.781 2.594,7.021 0.177,0.24 10 false 6 2.417,5.938 2.583,6.198 0.167,0.26 10 false 1 3.583,5.948 3.677,6.083 0.094,0.135 10 false 1 3.406,6.417 5.667,6.688 2.26,0.271 10 false Rear Door Courtesy Light Switch LH 3.406,6.281 3.719,6.542 0.313,0.26 10 false N15 4.188,3.99 4.896,4.26 0.708,0.271 10 false (for Center) 4.292,4.521 4.792,4.771 0.5,0.25 10 false (for RH)

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch signal CLOSE or OPEN CLOSE: Rear door RH closed
OPEN: Rear door RH open
-
RL Door Courtesy SW Rear door courtesy light switch signal CLOSE or OPEN CLOSE: Rear door LH closed
OPEN: Rear door LH open
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25
OK:

ON or OFF appears on the tester screen according to the rear door condition.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT BELT WARNING

NG

2.CHECK REAR SEAT BELT WARNING
a.
B294180C02
1.115,1.438 1.115,1.833 false 1.698,1.438 1.698,1.833 false 2.292,1.438 2.292,1.833 false 0.219,0.188 0.521,0.531 0.302,0.344 10 false *a 1.042,1.854 1.302,2.104 0.26,0.25 10 false *b 1.625,1.854 1.917,2.083 0.292,0.229 10 false *c 2.219,1.854 2.583,2.156 0.365,0.302 10 false *d
*a Rear Seat Belt Warning Light (Clock Assembly)
*b LH
*c Center
*d RH


Check the rear seat belt warning function.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY>REMOVAL


Result:
Result Proceed to
The rear seat belt warning lights operation is normal A
The rear seat belt warning lights (all seat) operation is not normal B
The rear seat belt warning light (RH) operation is not normal C
The rear seat belt warning light (center) operation is not normal D
The rear seat belt warning light (LH) operation is not normal E



A

B

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)

C

6.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR RH))

D

10.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER))

E

14.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR LH))
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.


Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

4.CHECK HARNESS AND CONNECTOR (BATTERY - CLOCK ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BATTERY - CLOCK ASSEMBLY)
a.

Disconnect the I170 clock assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I170-8 (IG+) - Body ground ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Reconnect the I170 clock assembly connector.


b.

Disconnect the I17 combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I17-6 (RLMT) - Body ground Always 11 to 14 V
I17-2 (RCMT) - Body ground Always 11 to 14 V
I17-3 (RRMT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

6.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR RH))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.


Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR RH) - BODY GROUND)

B

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR RH) - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the O29 rear seat inner with center belt assembly RH (for RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-6 (RRSB) - O29-1 Always Below 1 Ω
I18-6 (RRSB) - Body ground Always 10 kΩ or higher
O29-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (FOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.


Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

9.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the I170 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-3 (RRMT) - I170-5 (RRID) Always Below 1 Ω
I17-3 (RRMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR CENTER))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.


Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR CENTER) - BODY GROUND)

B

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT RH (FOR CENTER) - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the O30 rear seat inner with center belt assembly RH (for center) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-5 (RCSB) - O30-1 Always Below 1 Ω
I18-5 (RCSB) - Body ground Always 10 kΩ or higher
O30-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (FOR CENTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.


Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

13.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the I170 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-2 (RCMT) - I170-6 (RCID) Always Below 1 Ω
I17-2 (RCMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING INTELLIGENT TESTER (REAR SEAT BELT BUCKLE SWITCH (FOR LH))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.


Result:
Result Proceed to
ON or OFF does not appear on the tester screen according to the rear seat belt condition A
ON or OFF appears on the tester screen according to the rear seat belt condition B



A

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT LH - BODY GROUND)

B

16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - REAR SEAT INNER WITH CENTER BELT LH - BODY GROUND)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the N41 rear seat inner with center belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-10 (RLSB) - N41-1 Always Below 1 Ω
I18-10 (RLSB) - Body ground Always 10 kΩ or higher
N41-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR SEAT BELT WARNING LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.


Result:
Result Proceed to
The rear seat belt warning light does not operate normally A
The rear seat belt warning light operates normally B



A

17.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

B

REPLACE COMBINATION METER ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I17 combination meter assembly connector.


b.

Disconnect the I170 clock assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-6 (RLMT) - I170-7 (RLID) Always Below 1 Ω
I17-6 (RLMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR