Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.05
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0074736 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog lights via the engine room junction block assembly.

WIRING DIAGRAM

E220286E10
6,0.917 6.406,1.094 0.406,0.177 10 false TRLY 6,2.542 6.448,2.719 0.448,0.177 10 false RFGO 0.385,0.885 1.167,1.063 0.781,0.177 10 false from Battery 4.063,2.885 5.688,3.219 1.625,0.333 10 false Instrument Panel Junction Block Assembly 5.76,0.823 5.938,1 0.177,0.177 10 false 14 5.76,2.448 5.938,2.625 0.177,0.177 10 false 27 3.969,0.896 4.177,1.073 0.208,0.177 10 false 3E 4.01,0.708 4.104,0.885 0.094,0.177 10 false 1 3.969,2.125 4.198,2.302 0.229,0.177 10 false 3D 4.01,1.938 4.104,2.115 0.094,0.177 10 false 9 3.969,2.531 4.198,2.708 0.229,0.177 10 false 3D 3.969,2.344 4.146,2.521 0.177,0.177 10 false 35 1.344,2.125 1.552,2.302 0.208,0.177 10 false 1G 1.385,1.948 1.479,2.125 0.094,0.177 10 false 2 1.354,2.542 1.583,2.719 0.229,0.177 10 false 1F 0.844,2.125 1.177,2.302 0.333,0.177 10 false TAIL 1.385,1.573 1.51,1.75 0.125,0.177 10 false B 1.385,1.385 1.479,1.563 0.094,0.177 10 false 1 0.896,1.573 1.177,1.75 0.281,0.177 10 false ALT 0.75,2.542 1.167,2.719 0.417,0.177 10 false RFGS 1.354,2.354 1.531,2.531 0.177,0.177 10 false 10 2.198,1.063 2.49,1.24 0.292,0.177 10 false ALT 4.938,1.406 5.25,1.583 0.313,0.177 10 false TAIL 4.938,2.271 5.25,2.448 0.313,0.177 10 false TAIL 5.469,4.333 7.115,4.667 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,4.167 5.781,4.344 0.313,0.177 10 false MB 0.073,5.729 1.49,6.063 1.417,0.333 10 false Engine Room Junction Block Assembly 2.677,2.948 3.458,3.125 0.781,0.177 10 false from Battery 2.677,1.563 3.635,1.74 0.958,0.177 10 false from ALT Fuse 1.333,3.375 1.563,3.552 0.229,0.177 10 false 1F 0.729,3.396 1.146,3.573 0.417,0.177 10 false GND1 1.375,3.177 1.469,3.354 0.094,0.177 10 false 3 1.333,3.813 1.563,3.99 0.229,0.177 10 false 1G 0.729,3.833 1.146,4.01 0.417,0.177 10 false GND2 1.375,3.615 1.469,3.792 0.094,0.177 10 false 4 1.375,2.948 1.51,3.125 0.135,0.177 10 false A 1.385,2.76 1.479,2.938 0.094,0.177 10 false 1 0.802,2.948 1.177,3.125 0.375,0.177 10 false BATT 1.354,4.406 1.583,4.583 0.229,0.177 10 false 1F 1.344,4.229 1.521,4.406 0.177,0.177 10 false 12 2.26,4.594 2.646,4.854 0.385,0.26 10 false T27 2.26,4.75 3.823,4.927 1.563,0.177 10 false Rear Light Assembly LH 2.26,5.729 2.667,5.99 0.406,0.26 10 false T26 2.26,5.885 3.844,6.063 1.583,0.177 10 false Rear Light Assembly RH 2.823,4.292 2.917,4.469 0.094,0.177 10 false 4 3.208,4.292 3.302,4.469 0.094,0.177 10 false 3 2.823,5.427 2.917,5.604 0.094,0.177 10 false 4 3.208,5.427 3.302,5.604 0.094,0.177 10 false 3 0.719,4.406 1.156,4.583 0.438,0.177 10 false RFOG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay ON/OFF Make sure the light control switch is in the tail position
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates. (Rear fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
3.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Using a voltmeter, check the signal reading of the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)

NG

INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE AND BODY GROUND)
a.

Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

E230000C11
2.781,2.615 3.094,2.813 0.313,0.198 4.729,2.708 5.042,2.906 0.313,0.198 6.188,3.094 6.5,3.292 0.313,0.198 0.771,3.073 1.083,3.271 0.313,0.198 5.104,3.656 5.271,3.979 false 0.865,3.583 0.792,3.896 false 2.615,3.688 2.552,4.135 false 6.281,3.625 6.219,3.948 false 2.865,2.635 3.271,2.896 0.406,0.26 10 1F 4.802,2.729 5.469,3.125 0.667,0.396 10 1G 6.302,3.115 6.75,3.438 0.448,0.323 10 A 0.875,3.094 1.406,3.469 0.531,0.375 10 B 0.271,0.208 0.688,0.552 0.417,0.344 10 *a 6.083,3.958 6.781,4.323 0.698,0.365 10 BATT 5.115,4 5.823,4.333 0.708,0.333 10 GND2 2.344,4.167 3.24,4.542 0.896,0.375 10 GND1 0.646,3.927 1.5,4.344 0.854,0.417 10 ALT
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 (BATT) - Body ground Always 11 to 14 V
B-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-3 (GND1) - Body ground Always Below 1 Ω
1G-4 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-2 (TAIL) - 3D-9 Always Below 1 Ω
1F-10 (RFGS) - 3D-35 Always Below 1 Ω
1G-2 (TAIL) or 3D-9 - Body ground Always 10 kΩ or higher
1F-10 (RFGS) or 3D-35 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

E268794C01
1.583,0.583 2,0.833 0.417,0.25 3.333,2.167 3.75,2.417 0.417,0.25 5.25,0.417 5.667,0.667 0.417,0.25 2.979,3.167 3.396,2.75 false 4.75,3.167 4.417,2.75 false 0.188,0.156 0.5,0.313 0.313,0.156 10 *a 1.708,0.625 2.083,0.854 0.375,0.229 10 3E 3.448,2.219 3.823,2.448 0.375,0.229 10 MB 5.375,0.458 5.75,0.688 0.375,0.229 10 3D 2.802,3.177 3.417,3.375 0.615,0.198 10 TRLY 4.604,3.188 5.219,3.385 0.615,0.198 10 RFGO
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-27 (RFGO) - 3D-35 Always Below 1 Ω
MB-27 (RFGO) or 3D-35 - Body ground Always 10 kΩ or higher



d.

Connect a positive (+) lead from the battery to terminal 3E-1.


e.

Connect a negative (-) lead from the battery to terminal MB-14.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-9 - Battery negative Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR LIGHT ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR LIGHT ASSEMBLY)
a.

Disconnect the 1F engine room junction block assembly connector.


b.

Disconnect the T27 and T26 rear light assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-12 (RFOG) - T27-4 Always Below 1 Ω
1F-12 (RFOG) - T26-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T27-3 - Body ground Always Below 1 Ω
T26-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY
a.

Replace the engine room junction block assembly with a new or a known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Check that the rear fog lights operate normally.

OK:

The rear fog lights operate normally.



Result:
Proceed to
OK
NG



OK

END (ENGINE ROOM JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)