Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM U

2GR-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:
·

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

·

The actual values may differ from the values listed in the chart under "Reference Value" due to climate, weather conditions, etc.



HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in P, the A/C switch should be off and all accessory switches should be off.


a.

Warm up the engine.


b.

Turn the A/C switch off.


c.

Turn the engine switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG).


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Data List.

HINT:
·

To display the list box, press the pull down menu button next to Primary. Then select a measurement group.

·

When you select a measurement group, the ECU data belonging to that group is displayed.

·

Measurement Group List / Description

·

All Data / All data

·

Primary / -

·

Engine Control / Engine control system related data

·

Ptrl General / -

·

Ptrl AF Control / Air fuel ratio control system related data

·

Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data

·

Ptrl Throttle / Gasoline throttle system related data

·

Ptrl Intake Control / Intake control system related data

·

Ptrl Valve Control / Valve control system related data

·

Ptrl Misfire / "Misfire" related data

·

Ptrl Starting / "Difficult to start" related data

·

Ptrl Rough Idle / "Rough idle" related data

·

Ptrl Evaporative / Evaporative system related data

·

Ptrl CAT Converter / Catalyst converter related data

·

Check Mode / Check mode related data

·

Monitor Status / Monitor status related data

·

Ignition / Ignition system related data

·

Charging Control / Charging control system related data

·

Compression / Data used during "Check the Cylinder Compression" Active Test

·

AT / Automatic transaxle system related data

·

Vehicle Information / Vehicle information





h.

According to the display on the GTS, read the Data List.

HINT:
·

The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.

·

"Reference Value" is the assessment of one vehicle. Use it only for reference.





Various Vehicle Conditions 1 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed -
·

Stored as Freeze Frame Data: Yes

·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

·

There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

·

To accurately confirm whether the vehicle was stopped or not, use "SPD (NO)", which is the automatic transaxle output speed.



Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 600 to 700 rpm: Idling Idling (engine warmed up and A/C off): 660 rpm
·

Stored as Freeze Frame Data: Yes

·

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.


Calculate Load Load calculated by ECM Min.: 0%, Max.: 100% -
·

Engine switch on (IG): 0.0%

·

Idling (engine warmed up): 23.5%

·

Running without load (3000 rpm): 22.3%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 59.6%


·

Stored as Freeze Frame Data: Yes

·

This is the engine load calculated based on the estimated intake pressure.

·

Calculate Load = Estimated intake pressure / maximum intake pressure x 100 (%)

(For example, when the estimated intake pressure is the same as atmospheric pressure, Calculate Load is 100%.)


Vehicle Load Vehicle load Min.: 0%, Max.: 25700% Actual vehicle load
·

Engine switch on (IG): 0.0%

·

Idling (engine warmed up): 10.5%

·

Running without load (3000 rpm): 12.1%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 32.5%


·

Stored as Freeze Frame Data: Yes

·

This is the engine intake air charging efficiency.

·

Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow x 100 (%)

Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)


HINT:

Due to individual engine differences, intake air temperature, etc., the value may exceed 100%.

Intake airflow (g/rev.) = Intake airflow (gm/sec) x 60 / Engine speed (rpm)

(Intake airflow (gm/sec) is value of MAF)


MAF Airflow rate from mass air flow meter sub-assembly Min.: 0 gm/sec, Max.: 655.35 gm/sec
·

2.0 to 5.0 gm/sec: Idling

·

8 to 19 gm/sec: 2500 rpm (without load)


·

Engine switch on (IG): 0.39 gm/sec

·

Idling (engine warmed up): 2.50 gm/sec

·

Running without load (2500 rpm): 10.29 gm/sec

·

Running without load (3000 rpm): 12.78 gm/sec

·

Vehicle driven at constant speed of 40 km/h (25 mph): 5.06 gm/sec

·

Vehicle driven at constant speed of 60 km/h (37 mph): 13.84 gm/sec

·

Vehicle driven at constant speed of 80 km/h (50 mph): 18.09 gm/sec


·

Stored as Freeze Frame Data: Yes

·

This is the intake air amount measured by the mass air flow meter sub-assembly.


Atmosphere Pressure Atmospheric pressure Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1913 mmHg) Equivalent to atmospheric pressure Idling (engine warmed up): 99 kPa(abs) [743 mmHg(abs)]
·

Stored as Freeze Frame Data: Yes

·

This value is calculated from the intake air amount.

·

Standard atmospheric pressure: 101 kPa(abs) [758 mmHg(abs)]

·

For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies depending on the weather.


Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up -
·

Stored as Freeze Frame Data: Yes

·

This is the engine coolant temperature.


HINT:
·

After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.

·

Check if the engine overheats if the value indicated 140°C (284°F).



Intake Air Intake air temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) Equivalent to temperature at location of mass air flow meter sub-assembly -
·

Stored as Freeze Frame Data: Yes

·

This is the engine intake air temperature.


HINT:
·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.



Engine Run Time Engine run time Min.: 0 s, Max.: 65535 s Time after engine start -
·

Stored as Freeze Frame Data: Yes

·

This is the time elapsed since the engine was started.


Initial Engine Coolant Temp Engine coolant temperature when the engine switch is turned on (IG) Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) - -
·

Stored as Freeze Frame Data: Yes

·

This is the engine coolant temperature stored when the engine switch is turned on (IG).


Initial Intake Air Temp Intake air temperature when the engine switch is turned on (IG) Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) - -
·

Stored as Freeze Frame Data: Yes

·

This is the intake air temperature stored when the engine switch is turned on (IG).


Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V: Engine switch on (IG)
·

Engine switch on (IG): 12.480 V

·

Cranking: 12.363 V

·

Idling (engine warmed up): 13.281 V


·

Stored as Freeze Frame Data: Yes

·

If 11 V or less, characteristics of some electrical components may change.


Glow Indicator Supported Status of glow indicator supported Unsupp or Supp Unsupp - Stored as Freeze Frame Data: Yes
Glow Indicator Glow indicator ON or OFF OFF - Stored as Freeze Frame Data: Yes

Throttle Control 1 (Ptrl Throttle)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Accelerator Position Accelerator pedal position Min.: 0%, Max.: 399.9% Actual accelerator pedal position
·

Engine switch on (IG): 0.0% (accelerator pedal fully released)

·

Engine switch on (IG): 100.0% (accelerator pedal fully depressed)


·

Stored as Freeze Frame Data: No

·

This is the accelerator pedal position defined using the learned fully released position (sensor output) of No. 1 accelerator pedal position sensor as 0% and the fully depressed position as 100%.


Accel Sens. No.1 Volt % Absolute No. 1 accelerator pedal position Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal fully released

·

52 to 90%: Accelerator pedal fully depressed


·

Engine switch on (IG): 15.6% (accelerator pedal fully released)

·

Engine switch on (IG): 68.2% (accelerator pedal fully depressed)


·

Stored as Freeze Frame Data: Yes

·

The No. 1 accelerator pedal position sensor output is converted using 5 V = 100%.


HINT:

If there are no accelerator pedal position sensor DTCs stored, it is possible to conclude that the accelerator pedal position sensor system is normal.


Accel Sens. No.2 Volt % Absolute No. 2 accelerator pedal position Min.: 0%, Max.: 100%
·

24 to 40%: Accelerator pedal fully released

·

68 to 95%: Accelerator pedal fully depressed


·

Engine switch on (IG): 31.7% (accelerator pedal fully released)

·

Engine switch on (IG): 83.9% (accelerator pedal fully depressed)


·

Stored as Freeze Frame Data: Yes

·

The No. 2 accelerator pedal position sensor output is converted using 5 V = 100%.



Throttle Control 2 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Accel Sensor Out No.1 No. 1 accelerator pedal position sensor voltage Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal fully released

·

2.6 to 4.5 V: Accelerator pedal fully depressed


·

Engine switch on (IG): 0.810 V (accelerator pedal fully released)

·

Engine switch on (IG): 3.398 V (accelerator pedal fully depressed)


·

Stored as Freeze Frame Data: No

·

This is the voltage output from the No. 1 accelerator pedal position sensor.


Accel Sensor Out No.2 No. 2 accelerator pedal position sensor voltage Min.: 0 V, Max.: 4.98 V
·

1.2 to 2.0 V: Accelerator pedal fully released

·

3.4 to 4.98 V: Accelerator pedal fully depressed


·

Engine switch on (IG): 1.582 V (accelerator pedal fully released)

·

Engine switch on (IG): 4.179 V (accelerator pedal fully depressed)


·

Stored as Freeze Frame Data: No

·

This is the voltage output from the No. 2 accelerator pedal position sensor.

·

The No. 2 accelerator pedal position sensor is used to monitor the No. 1 accelerator pedal position sensor. When there is a malfunction in the No. 1 accelerator pedal position sensor, the ECM uses the No. 2 accelerator pedal position sensor to control the engine.



Throttle Control 3 (Ptrl Throttle)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting released accelerator pedal ON or OFF ON: Accelerator pedal fully released
·

Engine switch on (IG): ON (accelerator pedal fully released)

·

Engine switch on (IG): OFF (accelerator pedal depressed)


·

Stored as Freeze Frame Data: No

·

This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position.


Accel Fully Close Learn #1 Accelerator fully released learned value (No. 1) Min.: 0 deg, Max.: 124.5 deg - Engine switch on (IG): 19.5 deg
·

Stored as Freeze Frame Data: No

·

This is the value of No. 1 accelerator pedal position sensor learned when the accelerator pedal is released.


Accel Fully Close Learn #2 Accelerator fully released learned value (No. 2) Min.: 0 deg, Max.: 124.5 deg - Engine switch on (IG): 39.5 deg
·

Stored as Freeze Frame Data: No

·

This is the value of No. 2 accelerator pedal position sensor learned when the accelerator pedal is released.


Throttle Sensor Volt % Absolute No. 1 throttle position sensor Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed


·

Engine switch on (IG): 18.8% (accelerator pedal fully released)

HINT:

The throttle valve is not completely closed, but is kept open a certain amount by the throttle valve opener.


·

Engine switch on (IG): 81.1% (accelerator pedal fully depressed)

·

Idling (engine warmed up): 14.5%

·

Running without load (3000 rpm): 19.2%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 19.6%


·

Stored as Freeze Frame Data: Yes

·

The No. 1 throttle position sensor output is converted using 5 V = 100%.


HINT:

If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.


Throttl Sensor #2 Volt % Absolute No. 2 throttle position sensor Min.: 0%, Max.: 100%
·

42 to 62%: Accelerator pedal fully released

·

92 to 100%: Accelerator pedal fully depressed


·

Engine switch on (IG): 50.5% (accelerator pedal fully released)

HINT:

The throttle valve is not completely closed, but is kept open a certain amount by the throttle valve opener.


·

Engine switch on (IG): 99.6% (accelerator pedal fully depressed)

·

Idling (engine warmed up): 45.4%


·

Stored as Freeze Frame Data: Yes

·

The No. 2 throttle position sensor output is converted using 5 V = 100%.


ST1 Brake pedal signal ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
·

Stored as Freeze Frame Data: No

·

This is the stop light switch assembly signal (ST1- terminal).


System Guard System guard ON or OFF ON Idling (engine warmed up): ON
·

Stored as Freeze Frame Data: No

·

When there is a difference between the target and actual throttle valve opening angle, this item changes to OFF and the electronic throttle control system operation is disabled.

·

OFF: Electronic throttle control is stopped.


Open Side Malfunction Open malfunction ON or OFF OFF -
·

Stored as Freeze Frame Data: No

·

This item indicates a malfunction in the electronic throttle when the throttle valve is open.


Throttle Idle Position Whether or not throttle position sensor detecting idle ON or OFF -
·

Engine switch on (IG): ON

HINT:

The throttle valve is not completely closed, but is kept open a certain amount by the throttle valve opener.


·

Idling (engine warmed up): ON

·

Running without load (3000 rpm): OFF


·

Stored as Freeze Frame Data: No

·

This is a parameter calculated by the ECM.

·

The value is ON when the throttle is at the idle position and OFF when the throttle is open.


Throttle Require Position Required throttle position Min.: 0 V, Max.: 4.98 V -
·

Engine switch on (IG): 0.781 V (accelerator pedal fully released)

·

Engine switch on (IG): 4.042 V (accelerator pedal fully depressed)

·

Idling (engine warmed up): 0.722 V


·

Stored as Freeze Frame Data: No

·

The value of this item is calculated by the ECM and shows the voltage for the target throttle valve position. It is almost an exact match of the Throttle Position No. 1 value except during very rapid throttle valve movement, such as that used during wheelspin control.


Throttle Sensor Position Throttle sensor position Min.: 0%, Max.: 100%
·

0%: Accelerator pedal fully released

·

50 to 80%: Accelerator pedal fully depressed


Idling (engine warmed up): 0.0%
·

Stored as Freeze Frame Data: Yes

·

This is the throttle valve opening amount used for engine control.

·

The value of this item has no meaning when the engine switch on (IG) and the engine is not running.

·

The throttle valve opening amount during idle is indicated by 0%.


Throttle Position No.1 No. 1 throttle position sensor output voltage Min.: 0 V, Max.: 4.98 V Almost same as "Throttle Require Position"
·

0.5 to 1.1 V: Accelerator pedal fully released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


·

Engine switch on (IG): 0.937 V (accelerator pedal fully released)

·

Engine switch on (IG): 4.042 V (accelerator pedal fully depressed)

·

Idling (engine warmed up): 0.722 V


·

Stored as Freeze Frame Data: No

·

This is the No. 1 throttle position sensor output voltage.


Throttle Position No.2 No. 2 throttle position sensor output voltage Min.: 0 V, Max.: 4.98 V
·

2.1 to 3.1 V: Accelerator pedal fully released

·

4.6 to 4.98 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


·

Engine switch on (IG): 2.519 V (accelerator pedal fully released)

·

Engine switch on (IG): 4.906 V (accelerator pedal fully depressed)

·

Idling (engine warmed up): 2.265 V


·

Stored as Freeze Frame Data: No

·

This is the No. 2 throttle position sensor output voltage.


Throttle Position Command Throttle position command value Min.: 0 V, Max.: 4.98 V - -
·

Stored as Freeze Frame Data: No

·

The value displayed for this item is the same as Throttle Require Position.


Throttle Sens Open Pos #1 No. 1 throttle position sensor Min.: 0 V, Max.: 4.98 V 0.6 to 1.4 V Engine switch on (IG): 0.937 V
·

Stored as Freeze Frame Data: No

·

This is the No. 1 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released, the throttle valve is kept open by the throttle valve opener when the engine switch is on (IG).


Throttle Sens Open Pos #2 No. 2 throttle position sensor Min.: 0 V, Max.: 4.98 V 1.7 to 2.5 V Engine switch on (IG): 2.011 V
·

Stored as Freeze Frame Data: No

·

This is the No. 2 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released, the throttle valve is kept open by the throttle valve opener when the engine switch is on (IG).


Throttle Motor Current Throttle actuator current Min.: 0 A, Max.: 19.9 A 0 to 3.0 A: Idling
·

Engine switch on (IG): 0.0 A (accelerator pedal fully released)

·

Engine switch on (IG): 1.0 A (accelerator pedal fully depressed)

·

Idling (engine warmed up): 1.0 A

·

Running without load (3000 rpm): 0.5 A

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.3 A


·

Stored as Freeze Frame Data: No

·

When the value of this item is large but the actual opening angle (Throttle Position No. 1) does not reach the target opening angle (Throttle Require Position), there is an "unable to open" malfunction.


Throttle Motor DUTY Throttle actuator Min.: 0%, Max.: 100% 10 to 22%: Idling -
·

Stored as Freeze Frame Data: Yes

·

This is the output duty ratio of the throttle actuator drive circuit.


Throttle Motor Duty (Open) Throttle actuator duty ratio (open) Min.: 0%, Max.: 255% 0 to 40%: Idling
·

Engine switch on (IG): 0% (accelerator pedal fully released)

·

Engine switch on (IG): 17% (accelerator pedal fully depressed)

·

Idling (engine warmed up): 0%

·

Running without load (3000 rpm): 9%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 6%


·

Stored as Freeze Frame Data: No

·

This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal.


Throttle Motor Duty (Close) Throttle actuator duty ratio (close) Min.: 0%, Max.: 255% 0 to 40%: Idling
·

Engine switch on (IG): 0% (accelerator pedal fully released)

·

Engine switch on (IG): 0% (accelerator pedal fully depressed)

·

Idling (engine warmed up): 16%

·

Running without load (3000 rpm): 0%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0%


·

Stored as Freeze Frame Data: No

·

This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.


HINT:

During idle, the throttle valve opening angle is usually controlled using a duty ratio drive signal which closes the throttle valve. However, if carbon deposits have built up, it may be necessary to open the throttle valve more than the throttle valve opener does. In that case, the opening angle is controlled using the Throttle Motor Duty (Open) signal.


Throttle Fully Close Learn Throttle valve fully closed position (learned value) Min.: 0 V, Max.: 4.98 V 0.4 to 1.0 V: Accelerator pedal fully released Engine switch on (IG): 0.683 V
·

Stored as Freeze Frame Data: No

·

The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. The ECM calculates the learned value based on the position of the throttle valve when the accelerator pedal is released and the throttle valve motor is not operating.

·

Learning is performed immediately after the engine switch is turned on (IG).


+BM Voltage +BM voltage Min.: 0 V, Max.: 79.998 V 11 to 14 V: Engine switch on (IG) and system normal -
·

Stored as Freeze Frame Data: No

·

This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the engine switch is turned off).


Actuator Power Supply Actuator power supply ON or OFF ON: Idling -
·

Stored as Freeze Frame Data: No

·

If +BM power is lost, this item changes to OFF.


Throttle Position Throttle valve opening angle Min.: 0 deg, Max.: 499.99 deg - Idling (engine warmed up): 0.00 deg
·

Stored as Freeze Frame Data: Yes

·

This value has no meaning when the engine switch is on (IG) and the engine is stopped.



Idle Speed Control (Ptrl Rough Idle)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
ISC Flow Flow rate calculated using information from mass air flow meter sub-assembly Min.: 0 L/s, Max.: 79.99 L/s - Idling (engine warmed up): 1.82 L/s
·

Stored as Freeze Frame Data: Yes

·

This is the total ISC airflow amount (the amount of intake air necessary to maintain idling).


HINT:

ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


ISC Position Requested throttle opening amount calculated using ISC control Min.: 0 deg, Max.: 499.99 deg - Idling (engine warmed up): 0.80 deg
·

Stored as Freeze Frame Data: Yes

·

This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).


ISC Feedback Value ISC feedback amount Min.: -40 L/s, Max.: 39.99 L/s - Idling (engine warmed up): -0.01 L/s
·

Stored as Freeze Frame Data: Yes

·

This is the feedback amount necessary to adjust the airflow amount to maintain the target idle speed.


HINT:

When the idle speed differs from the target, the feedback amount is adjusted. If the feedback amount becomes more than a certain value, this will be reflected in the ISC learned airflow value.


ISC Learning Value ISC learned airflow value Min.: -40 L/s, Max.: 39.99 L/s - Idling (engine warmed up): 1.54 L/s
·

Stored as Freeze Frame Data: Yes

·

This is the learned value of the airflow amount necessary for engine idling.


HINT:
·

If ISC Feedback Value becomes more than a certain value, this will be reflected in ISC Learning Value.

·

ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount



Electric Load Feedback Val Compensation flow rate according to electrical load Min.: -40 L/s, Max.: 39.99 L/s - Idling (headlights and window defogger on): 0.70 L/s
·

Stored as Freeze Frame Data: Yes

·

This is the ISC compensation amount determined according to the electrical load.


Air Conditioner FB Val Compensation flow rate according to air conditioner load Min.: -40 L/s, Max.: 39.99 L/s - Idling (A/C on): 1.25 L/s
·

Stored as Freeze Frame Data: Yes

·

This is the ISC compensation amount determined according to the air conditioner load.


Low Revolution Control Low engine speed control operation state ON or OFF - Idling (engine warmed up): OFF
·

Stored as Freeze Frame Data: Yes

·

This item indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. This parameter changes to ON when the engine speed drops to below the following speeds 1 to 7 seconds after the engine is started (when the A/C is on, the engine speed thresholds below increase by 100 to 200 rpm).

·

900 rpm (when the engine coolant temperature is 10°C (50°F)).

·

850 rpm (when the engine coolant temperature is 30°C (86°F)).

·

750 rpm (when the engine coolant temperature is 60°C (140°F)).

Before 5 seconds elapse after starting the engine, this parameter indicates the status of the previous trip.

After 5 seconds elapse after starting the engine, this parameter indicates the status of the current trip.

HINT:

The engine is considered to have started when the engine speed reaches 400 rpm. When the engine speed decreases immediately after starting the engine, this parameter changes to ON and remains ON for the rest of the trip.

ON: The engine speed decreased immediately after starting the engine.

OFF: The engine speed did not decrease immediately after starting the engine.



·

For use when engine stall, starting problems or rough idle is present.


N Range Status Shift lever N status ON or OFF - - Stored as Freeze Frame Data: Yes
Eng Stall Control FB Flow Intake air compensation flow rate Min.: -40 L/s, Max.: 39.99 L/s - Idling (engine warmed up): 0.00 L/s
·

Stored as Freeze Frame Data: Yes

·

The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall.

·

For use when engine stall, starting problems or rough idle is present.


Deposit Loss Flow Flow loss due to deposits Min.: -40 L/s, Max.: 39.99 L/s - Idling (engine warmed up): 0.00 L/s
·

Stored as Freeze Frame Data: Yes

·

This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.

·

Check this value for reference when the engine stalls, is difficult to start, or idles roughly.

·

When the ISC learned value is initialized, performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.

·

Start the engine cold and allow the engine to idle.

·

After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.

·

Turn the engine switch off and wait for 30 seconds.

·

Start the engine again, and allow the engine to idle for 5 minutes.




Fuel System (Ptrl General)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Fuel Pump Duty Fuel pump duty ratio Min.: 0%, Max.: 399.9% -
·

Idling (engine warmed up): 60.8%

·

Running without load (3000 rpm): 63.5%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 60.8%


·

Stored as Freeze Frame Data: Yes

·

This item indicates the duty ratio of the fuel pump.


Injector (Port) Injection period of the No. 1 cylinder Min.: 0 μs, Max.: 65535 μs -
·

Idling (engine warmed up): 2093 μs

·

Running without load (3000 rpm): 2223 μs

·

Vehicle driven at constant speed of 60 km/h (37 mph): 3447 μs


·

Stored as Freeze Frame Data: Yes

·

This is the injection period of the No. 1 cylinder (the command value from the ECM).


Injection Volum (Cylinder1) Injection volume (cylinder 1) Min.: 0 ml, Max.: 2.047 ml 0 to 0.5 ml
·

Idling (engine warmed up): 0.083 ml

·

Running without load (3000 rpm): 0.093 ml

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.197 ml


·

Stored as Freeze Frame Data: Yes

·

This is the fuel injection volume for 10 injections.


Current Fuel Type Current fuel type - Gasoline/petrol - Stored as Freeze Frame Data: Yes

EVAP System (Ptrl Evaporative)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
EVAP (Purge) VSV Purge VSV control duty Min.: 0%, Max.: 100% -
·

Idling (engine warmed up): 29.8%

·

Running without load (3000 rpm): 100.0%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 96.8%


·

Stored as Freeze Frame Data: Yes

·

This is the command signal from the ECM.

·

This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed.

*: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV.

·

When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV will be 0%.


Evap Purge Flow Purge flow Min.: 0%, Max.: 399.9% -
·

Idling (engine warmed up): 9.9%

·

Running without load (3000 rpm): 8.3%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 7.8%


·

Stored as Freeze Frame Data: Yes

·

This is the percentage of total engine airflow contributed by EVAP purge operation.

(Evap Purge Flow = Purge flow / Engine airflow x 100 (%))


Purge Density Learn Value Purge density learned value Min.: -200, Max.: 199.993 - Idling (engine warmed up): 0.506
·

Stored as Freeze Frame Data: Yes

·

This is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate.

·

When the value of this item is a large negative value, the purge effect is large.

·

The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced.

·

Purge density learning is performed so that the feedback compensation value is 0 +/-2%.


HINT:
·

Usually, the value is approximately +/-1.

·

1: The concentration of HC in the purge gas is relatively low.

·

0: The concentration of HC in the purge gas is approximately equal to the stoichiometric air fuel ratio.

·

A large negative value indicates that the concentration of HC in the purge gas is relatively high.



EVAP Purge VSV VSV status for EVAP control ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

This item is ON when EVAP (Purge) VSV is approximately 30% or higher, and displays OFF when the VSV duty ratio is less than 30%.


Purge Cut VSV Duty Purge VSV duty Min.: 0%, Max.: 399.9% -
·

Idling (engine warmed up): 24.6%

·

Running without load (3000 rpm): 100.0%


Stored as Freeze Frame Data: Yes

Air Fuel Ratio Control 1 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Target Air-Fuel Ratio Target air fuel ratio Min.: 0, Max.: 1.99 0.8 to 1.2: During idling
·

Idling (engine warmed up): 0.998 (Performing feedback control at the stoichiometric air fuel ratio)

·

Running without load (3000 rpm): 0.998 (Performing feedback control at the stoichiometric air fuel ratio)

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.965 (Performing feedback control at the stoichiometric air fuel ratio)


·

Stored as Freeze Frame Data: Yes

·

This is the target air fuel ratio used by the ECM.

·

1.0 is the stoichiometric air fuel ratio. Values that are more than 1.0 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1.0 indicate the system attempting to make the air fuel ratio richer.

·

Target Air-Fuel Ratio and AF Lambda B1S1 (B2S1) are related.



Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
AF Lambda B1S1 Output air fuel ratio associated with bank 1 sensor 1 Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

1 = Stoichiometric air fuel ratio

·

Value more than 1 (1.001 to 1.999) = Lean


·

Idling (engine warmed up): 0.995

·

Running without load (3000 rpm): 0.992

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.971


·

Stored as Freeze Frame Data: Yes

·

This is the actual air fuel ratio calculated based on the air fuel ratio sensor output.

·

Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor.

·

Results of real-vehicle check when performing the Active Test:

·

Injection Volume: +/-0%

AF Lambda B1S1: 0.99

AFS Voltage B1S1: 3.29 V

AFS Current B1S1: 0.00 mA

O2S B1S2: 0.43 V



·

Injection Volume: -12.5%

AF Lambda B1S1: 1.16

AFS Voltage B1S1: 3.85 V

AFS Current B1S1: 0.20 mA

O2S B1S2: 0.015 V



·

Injection Volume: 12.5%

AF Lambda B1S1: 0.89

AFS Voltage B1S1: 2.59 V

AFS Current B1S1: -0.27 mA

O2S B1S2: 0.94 V




AF Lambda B2S1 Output air fuel ratio associated with bank 2 sensor 1 Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

1 = Stoichiometric air fuel ratio

·

Value more than 1 (1.001 to 1.999) = Lean


·

Idling (engine warmed up): 0.995

·

Running without load (3000 rpm): 0.992

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.971


·

Stored as Freeze Frame Data: Yes

·

This is the actual air fuel ratio calculated based on the air fuel ratio sensor output.

·

Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check the voltage output of the sensor.

·

Results of real-vehicle check when performing the Active Test:

·

Injection Volume: +/-0%

AF Lambda B2S1: 0.99

AFS Voltage B2S1: 3.29 V

AFS Current B2S1: 0.00 mA

O2S B2S2: 0.43 V



·

Injection Volume: -12.5%

AF Lambda B2S1: 1.16

AFS Voltage B2S1: 3.85 V

AFS Current B2S1: 0.20 mA

O2S B2S2: 0.015 V



·

Injection Volume: 12.5%

AF Lambda B2S1: 0.89

AFS Voltage B2S1: 2.59 V

AFS Current B2S1: -0.27 mA

O2S B2S2: 0.94 V




AFS Voltage B1S1 Air fuel ratio sensor output voltage for bank 1 sensor 1 Min.: 0 V, Max.: 7.99 V 2.8 to 3.8 V: Idling
·

Idling (engine warmed up): 3.298 V

·

Running without load (3000 rpm): 3.229 V

·

Vehicle driven at constant speed of 60 km/h (37 mph): 3.146 V

·

Fuel-cut during deceleration being performed: 3.204 V


·

Stored as Freeze Frame Data: Yes

·

This is the output voltage of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current B1S1 below for the actual sensor output).

·

Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output voltage of the sensor.

·

Results of real-vehicle check when performing the Active Test:

·

Injection Volume: +/-0%

AF Lambda B1S1: 0.99

AFS Voltage B1S1: 3.29 V

AFS Current B1S1: 0.00 mA

O2S B1S2: 0.43 V



·

Injection Volume: -12.5%

AF Lambda B1S1: 1.16

AFS Voltage B1S1: 3.85 V

AFS Current B1S1: 0.20 mA

O2S B1S2: 0.015 V



·

Injection Volume: 12.5%

AF Lambda B1S1: 0.89

AFS Voltage B1S1: 2.59 V

AFS Current B1S1: -0.27 mA

O2S B1S2: 0.94 V




AFS Voltage B2S1 Air fuel ratio sensor output voltage for bank 2 sensor 1 Min.: 0 V, Max.: 7.99 V 2.8 to 3.8 V: Idling
·

Idling (engine warmed up): 3.298 V

·

Running without load (3000 rpm): 3.229 V

·

Vehicle driven at constant speed of 60 km/h (37 mph): 3.146 V

·

Fuel-cut during deceleration being performed: 3.204 V


·

Stored as Freeze Frame Data: Yes

·

This is the output voltage of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to AFS Current B2S1 below for the actual sensor output).

·

Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output voltage of the sensor.

·

Results of real-vehicle check when performing the Active Test:

·

Injection Volume: +/-0%

AF Lambda B2S1: 0.99

AFS Voltage B2S1: 3.29 V

AFS Current B2S1: 0.00 mA

O2S B2S2: 0.43 V



·

Injection Volume: -12.5%

AF Lambda B2S1: 1.16

AFS Voltage B2S1: 3.85 V

AFS Current B2S1: 0.20 mA

O2S B2S2: 0.015 V



·

Injection Volume: 12.5%

AF Lambda B2S1: 0.89

AFS Voltage B2S1: 2.59 V

AFS Current B2S1: -0.27 mA

O2S B2S2: 0.94 V




AFS Current B1S1 Air fuel ratio sensor output current for bank 1 sensor 1 Min.: -128 mA, Max.: 127.99 mA -0.5 to 0.5 mA: Idling
·

Idling (engine warmed up): 0.00 mA

·

Running without load (3000 rpm): -0.03 mA

·

Vehicle driven at constant speed of 60 km/h (37 mph): -0.06 mA

·

Fuel-cut during deceleration being performed: -0.20 mA


·

Stored as Freeze Frame Data: Yes

·

With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA.

·

When the value is outside the range of 0.8 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit.


AFS Current B2S1 Air fuel ratio sensor output current for bank 2 sensor 1 Min.: -128 mA, Max.: 127.99 mA -0.5 to 0.5 mA: Idling
·

Idling (engine warmed up): 0.00 mA

·

Running without load (3000 rpm): -0.03 mA

·

Vehicle driven at constant speed of 60 km/h (37 mph): -0.06 mA

·

Fuel-cut during deceleration being performed: -0.20 mA


·

Stored as Freeze Frame Data: Yes

·

With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA.

·

When the value is outside the range of 0.8 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit.


A/F Heater Duty B1S1 Air fuel ratio sensor heater duty ratio for bank 1 sensor 1 Min.: 0%, Max.: 399.9% 0 to 100% Idling (engine warmed up): 22.6%
·

Stored as Freeze Frame Data: Yes

·

When the value of this item is more than 0%, current is being supplied to the heater.


A/F Heater Duty B2S1 Air fuel ratio sensor heater duty ratio for bank 2 sensor 1 Min.: 0%, Max.: 399.9% 0 to 100% Idling (engine warmed up): 22.6%
·

Stored as Freeze Frame Data: Yes

·

When the value of this item is more than 0%, current is being supplied to the heater.


O2S B1S2 Heated oxygen sensor output voltage for bank 1 sensor 2 Min.: 0 V, Max.: 1.275 V 0 to 1.0 V
·

Idling (engine warmed up): 0.720 V

·

Running without load (3000 rpm): 0.585 V


·

Stored as Freeze Frame Data: Yes

·

This is the output voltage of the heated oxygen sensor.

·

Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio.

·

Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio.

·

During air fuel ratio feedback control, the value moves back and forth between 0 to 1 V.

·

Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output voltage of the sensor.

·

Results of real-vehicle check when performing the Active Test:

·

Injection Volume: -12.5%

AF Lambda B1S1: 1.16

AFS Voltage B1S1: 3.85 V

AFS Current B1S1: 0.20 mA

O2S B1S2: 0.06 V



·

Injection Volume: 12.5%

AF Lambda B1S1: 0.89

AFS Voltage B1S1: 2.59 V

AFS Current B1S1: -0.27 mA

O2S B1S2: 0.94 V




O2S B2S2 Heated oxygen sensor output voltage for bank 2 sensor 2 Min.: 0 V, Max.: 1.275 V 0 to 1.0 V
·

Idling (engine warmed up): 0.720 V

·

Running without load (3000 rpm): 0.585 V


·

Stored as Freeze Frame Data: Yes

·

This is the output voltage of the heated oxygen sensor.

·

Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio.

·

Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio.

·

During air fuel ratio feedback control, the value moves back and forth between 0 to 1 V.

·

Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output voltage of the sensor.

·

Results of real-vehicle check when performing the Active Test:

·

Injection Volume: -12.5%

AF Lambda B2S1: 1.16

AFS Voltage B2S1: 3.85 V

AFS Current B2S1: 0.20 mA

O2S B2S2: 0.06 V



·

Injection Volume: 12.5%

AF Lambda B2S1: 0.89

AFS Voltage B2S1: 2.59 V

AFS Current B2S1: -0.27 mA

O2S B2S2: 0.94 V




O2 Heater B1S2 Heated oxygen sensor heater for bank 1 sensor 2 Active or Not Act - - Stored as Freeze Frame Data: Yes
O2 Heater B2S2 Heated oxygen sensor heater for bank 2 sensor 2 Active or Not Act - - Stored as Freeze Frame Data: Yes
O2 Heater Curr Val B1S2 Heated oxygen sensor current for bank 1 sensor 2 Min.: 0 A, Max.: 4.999 A -
·

Idling (engine warmed up): 0.952 A

·

Running without load (3000 rpm): 0.952 A


·

Stored as Freeze Frame Data: Yes

·

When the value of this item is more than 0 A, current is being supplied to the heater.


O2 Heater Curr Val B2S2 Heated oxygen sensor current for bank 2 sensor 2 Min.: 0 A, Max.: 4.999 A -
·

Idling (engine warmed up): 0.952 A

·

Running without load (3000 rpm): 0.952 A


·

Stored as Freeze Frame Data: Yes

·

When the value of this item is more than 0 A, current is being supplied to the heater.


Short FT #1 Short-term fuel trim for bank 1 Min.: -100%, Max.: 99.2% -15 to 15%
·

Idling (engine warmed up): 1.562%

·

Running without load (3000 rpm): 2.343%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.000%


·

Stored as Freeze Frame Data: Yes

·

This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback.


Long FT #1 Long-term fuel trim for bank 1 Min.: -100%, Max.: 99.2% -15 to 15%
·

Idling (engine warmed up): 5.468%

·

Running without load (3000 rpm): 7.812%

·

Vehicle driven at constant speed of 60 km/h (37 mph): -3.907%


·

Stored as Freeze Frame Data: Yes

·

The ECM will learn the Long FT #1 values based on Short FT #1. The goal is to keep Short FT #1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio.

·

This item is used to determine whether the system related to air fuel ratio control is malfunctioning.

·

The condition of the system is determined based on the sum of Short FT #1 and Long FT #1 (excluding times when the system is in transition).

·

15% or higher: The air fuel ratio may be lean.

·

-15 to 15%: The air fuel ratio can be determined to be normal.

·

-15% or less: The air fuel ratio may be rich.

·

Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT #1" indicates the learned value for the current operating range.

[A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.



Total FT #1 Total fuel trim for bank 1 Min.: -0.5, Max.: 0.496 -0.28 to 0.2: Idling -
·

Stored as Freeze Frame Data: Yes

·

Total FT #1 = Short FT #1 + Long FT #1


Short FT #2 Short-term fuel trim for bank 2 Min.: -100%, Max.: 99.2% -15 to 15%
·

Idling (engine warmed up): 1.562%

·

Running without load (3000 rpm): 2.343%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 0.000%


·

Stored as Freeze Frame Data: Yes

·

This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback.


Long FT #2 Long-term fuel trim for bank 2 Min.: -100%, Max.: 99.2% -15 to 15%
·

Idling (engine warmed up): 5.468%

·

Running without load (3000 rpm): 7.812%

·

Vehicle driven at constant speed of 60 km/h (37 mph): -3.907%


·

Stored as Freeze Frame Data: Yes

·

The ECM will learn the Long FT #2 values based on Short FT #2. The goal is to keep Short FT #2 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio.

·

This item is used to determine whether the system related to air fuel ratio control is malfunctioning.

·

The condition of the system is determined based on the sum of Short FT #2 and Long FT #2 (excluding times when the system is in transition).

·

15% or higher: The air fuel ratio may be lean.

·

-15 to 15%: The air fuel ratio can be determined to be normal.

·

-15% or less: The air fuel ratio may be rich.

·

Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT #2" indicates the learned value for the current operating range.

[A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.



Total FT #2 Total fuel trim for bank 2 Min.: -0.5, Max.: 0.496 -0.28 to 0.2: Idling -
·

Stored as Freeze Frame Data: Yes

·

Total FT #2 = Short FT #2 + Long FT #2


Fuel System Status #1 Fuel system status for bank 1 OL, CL, OLDrive, OLFault,CLFault or Unused CL: Idling after warming up -
·

Stored as Freeze Frame Data: Yes

·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Feedback for fuel control.

·

OLDrive: Open loop due to driving conditions (fuel enrichment).

·

OLFault: Open loop due to a detected system fault.

·

CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.


HINT:

CL (Closed Loop): During air fuel ratio feedback control, AF Lambda B1S1 is approximately 1.0 and AFS Voltage B1S1 is approximately 3.3 V.


Fuel System Status #2 Fuel system status for bank 2 OL, CL, OLDrive, OLFault,CLFault or Unused CL: Idling after warming up -
·

Stored as Freeze Frame Data: Yes

·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Feedback for fuel control.

·

OLDrive: Open loop due to driving conditions (fuel enrichment).

·

OLFault: Open loop due to a detected system fault.

·

CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.


HINT:

CL (Closed Loop): During air fuel ratio feedback control, AF Lambda B2S1 is approximately 1.0 and AFS Voltage B2S1 is approximately 3.3 V.


A/F Learn Value Idle #1 Air fuel ratio learn value of idle area for bank 1 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).


A/F Learn Value Low #1 Air fuel ratio learn value of low load area for bank 1 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).


A/F Learn Value Mid1 #1 Air fuel ratio learn value of middle 1 load area for bank 1 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the middle load range closer to the low load range (when the range of engine loads is divided into four parts).


A/F Learn Value Mid2 #1 Air fuel ratio learn value of middle 2 load area for bank 1 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the middle load range closer to the high load range (when the range of engine loads is divided into four parts).


A/F Learn Value High #1 Air fuel ratio learn value of high load area for bank 1 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).


A/F Learn Value Idle #2 Air fuel ratio learn value of idle area for bank 2 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).


A/F Learn Value Low #2 Air fuel ratio learn value of low load area for bank 2 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).


A/F Learn Value Mid1 #2 Air fuel ratio learn value of middle 1 load area for bank 2 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the middle load range closer to the low load range (when the range of engine loads is divided into four parts).


A/F Learn Value Mid2 #2 Air fuel ratio learn value of middle 2 load area for bank 2 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the middle load range closer to the high load range (when the range of engine loads is divided into four parts).


A/F Learn Value High #2 Air fuel ratio learn value of high load area for bank 2 Min.: -50%, Max.: 49.6% -15 to 15% -
·

Stored as Freeze Frame Data: Yes

·

Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).



Ignition System (Ignition)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
IGN Advance Ignition timing advance for No. 1 cylinder Min.: -64 deg, Max.: 63.5 deg 9.5 to 24.5 deg: Idling
·

Idling (engine warmed up): 21.5 deg

·

Running without load (3000 rpm): 40.0 deg

·

Vehicle driven at constant speed of 60 km/h (37 mph): 36.0 deg


Stored as Freeze Frame Data: Yes
Knock Feedback Value Knocking feedback value Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) -
·

Idling (engine warmed up): -1.5 deg(CA)

·

Running without load (3000 rpm): -1.5 deg(CA)

·

Vehicle driven at constant speed of 60 km/h (37 mph): -1.5 deg(CA)


·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing retard compensation amount determined by the presence or absence of knocking.

Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount

Example: 21 deg(CA)= 10 deg(CA) + 14 deg(CA) - 3 deg(CA)

*1: The most retarded timing value is a constant determined by the engine speed and engine load.

*2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3 deg(CA) as possible.

When Knock Feedback Value is less than -4 deg(CA), Knock Correct Learn Value is slowly decreased.

When Knock Feedback Value is higher than -2 deg(CA), Knock Correct Learn Value is slowly increased.

*3: The base value is -3 deg(CA) and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.


HINT:

If Knock Feedback Value does not change around the time when knocking occurs even though knocking continues (for example, stays at -3 deg(CA)), it can be determined that knocking is not being detected.

Possible Causes:
·

There is a problem with the knock control sensor sensitivity.

·

The knock control sensor is improperly installed.

·

There is a problem with a wire harness.



Knock Correct Learn Value Knocking correction learned value Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) -
·

Idling (engine warmed up): 16.8 deg(CA)

·

Running without load (3000 rpm): 15.5 deg(CA)

·

Vehicle driven at constant speed of 60 km/h (37 mph): 18.5 deg(CA)


·

Stored as Freeze Frame Data: Yes

·

Refer to "Knock Feedback Value".

·

When there is knocking or a lack of power, compare the values of following items to another vehicle of the same model.

·

Engine Speed

·

Calculate Load

·

IGN Advance

·

Knock Feedback Value

·

Knock Correct Learn Value


·

Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced.

·

Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.


HINT:

When knocking continues even though Knock Correct Learn Value is less than that of the vehicle being used for comparison (in other words, the ignition timing is being retarded but the knocking does not stop), there may be a buildup of deposits or other such problems due to deterioration over time (oil entering the cylinders, poor quality fuel, etc.).


Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1) Min.: 0 deg(CA), Max.: 15.93 deg(CA) - -
·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.

·

It may be possible to use this item to help determine specific cylinders which are not operating normally.


Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2) Min.: 0 deg(CA), Max.: 15.93 deg(CA) - -
·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.

·

It may be possible to use this item to help determine specific cylinders which are not operating normally.


Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3) Min.: 0 deg(CA), Max.: 15.93 deg(CA) - -
·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.

·

It may be possible to use this item to help determine specific cylinders which are not operating normally.


Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4) Min.: 0 deg(CA), Max.: 15.93 deg(CA) - -
·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.

·

It may be possible to use this item to help determine specific cylinders which are not operating normally.


Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5) Min.: 0 deg(CA), Max.: 15.93 deg(CA) - -
·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.

·

It may be possible to use this item to help determine specific cylinders which are not operating normally.


Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6) Min.: 0 deg(CA), Max.: 15.93 deg(CA) - -
·

Stored as Freeze Frame Data: Yes

·

This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.

·

It may be possible to use this item to help determine specific cylinders which are not operating normally.



Intake Control (Ptrl Intake Control)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
ACIS VSV Intake air control valve assembly for acoustic control induction system status ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

This is the ECM control command.


AICV VSV Vacuum switching valve for air intake control system status ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

This is the ECM control command.



VVT Control (Ptrl Valve Control)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
VVT Control Status #1 Variable Valve Timing (VVT) control status for bank 1 ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF).

·

OFF: The system is commanding the timing to change to the most retarded timing.


VVT Control Status #2 Variable Valve Timing (VVT) control status for bank 2 ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF).

·

OFF: The system is commanding the timing to change to the most retarded timing.


VVT Advance Fail VVT control failure status ON or OFF ON: VVT control failure -
·

Stored as Freeze Frame Data: Yes

·

ON: There is an intake VVT timing advance malfunction.


VVT Aim Angle #1 VVT hold duty learned value for bank 1 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced or retarded state of the VVT controller.

·

Refer to "VVT OCV Duty #1".


VVT Change Angle #1 VVT displacement angle for bank 1 Min.: 0 DegFR, Max.: 639.9 DegFR - -
·

Stored as Freeze Frame Data: No

·

This is the intake VVT displacement angle.

·

If the value of any "VVT Change Angle" does not change, there may be a malfunction in the respective VVT sensor circuit.

·

Refer to "VVT OCV Duty #1".


VVT OCV Duty #1 VVT camshaft timing oil control valve operation duty for bank 1 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This is the requested duty value.


Results of the real-vehicle check when performing the Control the VVT Linear (Bank 1) Active Test:
·

VVT OCV Duty #1 = 0%, VVT Change Angle #1 = 0 DegFR

·

VVT OCV Duty #1 = 30%, VVT Change Angle #1 = 0 DegFR

·

VVT OCV Duty #1 = 70%, VVT Change Angle #1 = 39.0 DegFR

·

VVT OCV Duty #1 = 100%, VVT Change Angle #1 = 39.0 DegFR

·

VVT OCV Duty #1 = 32%, VVT Change Angle #1 = 0 DegFR


After the above test, VVT Aim Angle #1 = 26.6%.
VVT Aim Angle #2 VVT hold duty learned value for bank 2 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced or retarded state of the VVT controller.

·

Refer to "VVT OCV Duty #2".


VVT Change Angle #2 VVT displacement angle for bank 2 Min.: 0 DegFR, Max.: 639.9 DegFR - -
·

Stored as Freeze Frame Data: No

·

This is the intake VVT displacement angle.

·

If the value of any "VVT Change Angle" does not change, there may be a malfunction in the respective VVT sensor circuit.

·

Refer to "VVT OCV Duty #2".


VVT OCV Duty #2 VVT camshaft timing oil control valve operation duty for bank 2 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This is the requested duty value.


Results of the real-vehicle check when performing the Control the VVT Linear (Bank 2) Active Test:
·

VVT OCV Duty #2 = 0%, VVT Change Angle #2 = 0 DegFR

·

VVT OCV Duty #2 = 30%, VVT Change Angle #2 = 0 DegFR

·

VVT OCV Duty #2 = 70%, VVT Change Angle #2 = 39.0 DegFR

·

VVT OCV Duty #2 = 100%, VVT Change Angle #2 = 39.0 DegFR

·

VVT OCV Duty #2 = 32%, VVT Change Angle #2 = 0 DegFR


After the above test, VVT Aim Angle #2 = 26.6%.
VVT Ex Hold Lrn Val #1 VVT exhaust hold duty ratio learned value for bank 1 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced or retarded state of the VVT controller.

·

Refer to "VVT Ex OCV Duty #1".


VVT Ex Chg Angle #1 VVT exhaust displacement angle for bank 1 Min.: 0 DegFR, Max.: 639.9 DegFR - -
·

Stored as Freeze Frame Data: No

·

This is the VVT displacement angle.

·

If the value of any "VVT Ex Chg Angle" does not change, there may be a malfunction in the respective VVT sensor circuit.

·

Refer to "VVT Ex OCV Duty #1".


VVT Ex OCV Duty #1 VVT exhaust camshaft timing oil control valve duty for bank 1 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This is the requested duty value.


Results of the real-vehicle check when performing the Control the VVT Exhaust Linear (Bank 1) Active Test:
·

VVT Ex OCV Duty #1 = 0%, VVT Ex Chg Angle #1 = 0 DegFR

·

VVT Ex OCV Duty #1 = 30%, VVT Ex Chg Angle #1 = 0 DegFR

·

VVT Ex OCV Duty #1 = 70%, VVT Ex Chg Angle #1 = 38.5 DegFR

·

VVT Ex OCV Duty #1 = 100%, VVT Ex Chg Angle #1 = 38.5 DegFR

·

VVT Ex OCV Duty #1 = 27.4%, VVT Ex Chg Angle #1 = 0 DegFR


After the above test, VVT Ex Hold Lrn Val #1 = 44.0%.
VVT Ex Hold Lrn Val #2 VVT exhaust hold duty ratio learned value for bank 2 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This value represents the duty ratio necessary to operate the camshaft timing oil control valve assembly in order to block the camshaft timing oil control valve assembly path and maintain the advanced or retarded state of the VVT controller.

·

Refer to "VVT Ex OCV Duty #2".


VVT Ex Chg Angle #2 VVT exhaust displacement angle for bank 2 Min.: 0 DegFR, Max.: 639.9 DegFR - -
·

Stored as Freeze Frame Data: No

·

This is the VVT displacement angle.

·

If the value of any "VVT Ex Chg Angle" does not change, there may be a malfunction in the respective VVT sensor circuit.

·

Refer to "VVT Ex OCV Duty #2".


VVT Ex OCV Duty #2 VVT exhaust camshaft timing oil control valve duty for bank 2 Min.: 0%, Max.: 399.9% - -
·

Stored as Freeze Frame Data: No

·

This is the requested duty value.


Results of the real-vehicle check when performing the Control the VVT Exhaust Linear (Bank 2) Active Test:
·

VVT Ex OCV Duty #2 = 0%, VVT Ex Chg Angle #2 = 0 DegFR

·

VVT Ex OCV Duty #2 = 30%, VVT Ex Chg Angle #2 = 0 DegFR

·

VVT Ex OCV Duty #2 = 70%, VVT Ex Chg Angle #2 = 38.5 DegFR

·

VVT Ex OCV Duty #2 = 100%, VVT Ex Chg Angle #2 = 38.5 DegFR

·

VVT Ex OCV Duty #2 = 27.4%, VVT Ex Chg Angle #2 = 0 DegFR


After the above test, VVT Ex Hold Lrn Val #2 = 44.0%.
VVT Target Angle #1 VVT target angle for bank 1 Min.: 0 DegFR, Max.: 639.9 DegFR - - Stored as Freeze Frame Data: No
VVT Target Angle #2 VVT target angle for bank 2 Min.: 0 DegFR, Max.: 639.9 DegFR - - Stored as Freeze Frame Data: No
VVT Ex Target Angle #1 VVT exhaust target angle for bank 1 Min.: 0 DegFR, Max.: 639.9 DegFR - - Stored as Freeze Frame Data: No
VVT Ex Target Angle #2 VVT exhaust target angle for bank 2 Min.: 0 DegFR, Max.: 639.9 DegFR - - Stored as Freeze Frame Data: No

Various Vehicle Conditions 2 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
VN Turbo Type VN turbo type Not Avl, Commo, Vacuum, CAN Com or DC Not Avl -
·

Stored as Freeze Frame Data: No

·

Indicates the VN turbo vane actuation method.



Catalyst (Ptrl CAT Converter)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Catalyst Temp B1S1 Front catalyst temperature for bank 1 Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) - -
·

Stored as Freeze Frame Data: Yes

·

This is the temperature of the front catalyst estimated by the ECM.

·

This value is included in the conditions used to detect catalyst deterioration (DTC P0420), etc., and should therefore be used as a reference when recreating malfunction conditions.


Catalyst Temp B2S1 Front catalyst temperature for bank 2 Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) - -
·

Stored as Freeze Frame Data: Yes

·

This is the temperature of the front catalyst estimated by the ECM.

·

This value is included in the conditions used to detect catalyst deterioration (DTC P0430), etc., and should therefore be used as a reference when recreating malfunction conditions.


Catalyst Temp B1S2 Rear catalyst temperature for bank 1 Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) - -
·

Stored as Freeze Frame Data: Yes

·

This is the temperature of the rear catalyst estimated by the ECM.


Catalyst Temp B2S2 Rear catalyst temperature for bank 2 Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) - -
·

Stored as Freeze Frame Data: Yes

·

This is the temperature of the rear catalyst estimated by the ECM.



Various Vehicle Conditions 3 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Starter Signal Starter signal ON or OFF
·

ON: Starter operating

·

OFF: Starter not operating


- Stored as Freeze Frame Data: Yes
Power Steering Signal Power steering signal status ON or OFF ON: Power steering operating - Stored as Freeze Frame Data: Yes
Neutral Position SW Signal Park/Neutral position switch status ON or OFF ON: Shift lever in P or N - Stored as Freeze Frame Data: Yes
Stop Light Switch Stop light switch ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


- Stored as Freeze Frame Data: Yes
A/C Signal A/C switch status ON or OFF ON: A/C on - Stored as Freeze Frame Data: Yes
Idle Up Signal Idle up signal ON or OFF - - Stored as Freeze Frame Data: Yes
Closed Throttle Position SW Closed throttle position switch status ON or OFF
·

ON: Throttle fully closed

·

OFF: Throttle open


- Stored as Freeze Frame Data: Yes
Fuel Cut Condition Fuel cut condition status ON or OFF ON: Fuel cut operating - Stored as Freeze Frame Data: Yes
Immobiliser Communication Immobiliser communication ON or OFF ON: Normal - Stored as Freeze Frame Data: Yes

Check Mode (Check Mode)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Check Mode Check mode ON or OFF ON: Check mode on -
·

Stored as Freeze Frame Data: No

·

*


SPD Test Result Check mode result for vehicle speed sensor Compl or Incmpl - - Stored as Freeze Frame Data: No
Misfire Test Result Check mode result for misfire monitor Compl or Incmpl - - Stored as Freeze Frame Data: No
OXS1 Test Result Check mode result for heated oxygen sensor (bank 1) Compl or Incmpl - - Stored as Freeze Frame Data: No
OXS2 Test Result Check mode result for heated oxygen sensor (bank 2) Compl or Incmpl - - Stored as Freeze Frame Data: No
A/F Test Results #2 Check mode result for air fuel ratio sensor (bank 2) Compl or Incmpl - - Stored as Freeze Frame Data: No
A/F Test Results #1 Check mode result for air fuel ratio sensor (bank 1) Compl or Incmpl - - Stored as Freeze Frame Data: No

*: Refer to Check Mode Procedure.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE


Test Result (Monitor Status)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Complete Parts Monitor Comprehensive component monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


Fuel System Monitor Fuel system monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


Misfire Monitor Misfire monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


EGR/VVT Monitor EGR/VVT monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


EGR/VVT Monitor EGR/VVT monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


O2S(A/FS) Monitor O2S (A/FS) monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


O2S(A/FS) Monitor O2S (A/FS) monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


A/C Monitor A/C monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


A/C Monitor A/C monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


2nd Air Monitor 2nd air monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


2nd Air Monitor 2nd air monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


EVAP Monitor EVAP monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


EVAP Monitor EVAP monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


Heated Catalyst Monitor Heated catalyst monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


Heated Catalyst Monitor Heated catalyst monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


Catalyst Monitor Catalyst monitor Not Avl or Avail - -
·

Stored as Freeze Frame Data: No

·

*1


Catalyst Monitor Catalyst monitor Compl or Incmpl - -
·

Stored as Freeze Frame Data: No

·

*1


*1:

Avail: The monitor is available on the vehicle.

Not Avl: The monitor is not available on the vehicle.

Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the engine switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.


Various Vehicle Conditions 4 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
TC Terminal TC terminal status ON or OFF - - Stored as Freeze Frame Data: Yes
# Codes(Include History) Number of codes Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: No

·

This is the number of DTCs stored.


MIL MIL status ON or OFF OFF - Stored as Freeze Frame Data: No
MIL ON Run Distance Distance driven with MIL on Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile) - -
·

Stored as Freeze Frame Data: No

·

This is the distance driven since the MIL was illuminated.


Running Time from MIL ON Running time from MIL on Min.: 0 min, Max.: 65535 min Running time after MIL turned on - Stored as Freeze Frame Data: No
Time after DTC Cleared Time after DTCs cleared Min.: 0 min, Max.: 65535 min Time after DTCs cleared -
·

Stored as Freeze Frame Data: Yes

·

This is the time elapsed since DTCs were cleared (or since the vehicle left the factory). Time elapsed since the engine switch is turned off is not counted.


Distance from DTC Cleared Distance driven after DTCs cleared Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) Distance driven after DTCs cleared -
·

Stored as Freeze Frame Data: Yes

·

This is the distance driven since DTCs were cleared (or since the vehicle left the factory).


Warmup Cycle Cleared DTC Warmup cycles after DTCs cleared Min.: 0, Max.: 255 - -
·

Stored as Freeze Frame Data: Yes

·

This is the number of warmup cycles after the DTCs were cleared.

·

This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory).

*: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or higher and reaching a temperature of 70°C (158°F) or higher after the engine is started.


Dist Batt Cable Disconnect Distance driven after battery cable disconnected Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile) Total distance vehicle driven after battery cable disconnected - Stored as Freeze Frame Data: Yes
IG OFF Elapsed Time Time after engine switch off Min.: 0 min, Max.: 655350 min Cumulative time after engine switch off - Stored as Freeze Frame Data: Yes
OBD Requirements OBD requirement - EOBD (Euro OBD) - Stored as Freeze Frame Data: No
Number of Emission DTC Emissions-related DTCs Min.: 0, Max.: 127 - -
·

Stored as Freeze Frame Data: No

·

This is the number of emissions-related DTCs stored.


TC and TE1 TC and CG (TE1) terminals of DLC3 ON or OFF - - Stored as Freeze Frame Data: Yes
Total Distance Traveled Total distance traveled Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) - - Stored as Freeze Frame Data: Yes

Misfire (Ptrl Misfire)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Ignition Trig. Count Ignition counter Min.: 0, Max.: 65535 0 to 600 -
·

Stored as Freeze Frame Data: Yes

·

This is the cumulative number of ignitions.

·

This counter is incremented by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions.

·

The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by Ignition Trig. Count.

·

The misfire rate for each cylinder = Cylinder #1 to #6 Misfire Count / Ignition Trig. Count


HINT:
·

For 4-cylinder engines, the values range from 0 to 400.

·

For 6-cylinder engines, the values range from 0 to 600.

·

For 8-cylinder engines, the values range from 0 to 800.



Cylinder #1 Misfire Count Misfire count of cylinder 1 Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire count for each individual cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Cylinder #2 Misfire Count Misfire count of cylinder 2 Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire count for each individual cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Cylinder #3 Misfire Count Misfire count of cylinder 3 Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire count for each individual cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Cylinder #4 Misfire Count Misfire count of cylinder 4 Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire count for each individual cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Cylinder #5 Misfire Count Misfire count of cylinder 5 Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire count for each individual cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Cylinder #6 Misfire Count Misfire count of cylinder 6 Min.: 0, Max.: 255 0 -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire count for each individual cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


All Cylinders Misfire Count Misfire count of all cylinders Min.: 0, Max.: 255 0 to 35 -
·

Stored as Freeze Frame Data: Yes

·

This is the total misfire count of all cylinders.

·

This counter is increased by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions.


Misfire RPM Engine speed for first misfire range Min.: 0 rpm, Max.: 6375 rpm 0 rpm: 0 misfires -
·

Stored as Freeze Frame Data: Yes

·

This is the average engine speed recorded when misfiring occurs.

·

The value of this item is closer to the actual conditions of the vehicle at the time misfire occurred than the values of Engine Speed and Calculate Load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.


Misfire Load Engine load for first misfire range Min.: 0 g/rev, Max.: 3.98 g/rev 0 g/rev: 0 misfires -
·

Stored as Freeze Frame Data: Yes

·

This is the average engine load recorded when misfiring occurs.

·

The value of this item is closer to the actual conditions of the vehicle at the time misfire occurred than the values of Engine Speed and Calculate Load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.


HINT:

To convert g/rev to gm/sec: RPM / 60 x g/rev = gm/sec.


Misfire Margin Misfire monitoring Min.: -128%, Max.: 127% 0 to 127: Idling -
·

Stored as Freeze Frame Data: Yes

·

This is the misfire detection margin.

·

Misfire Margin = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100%

·

When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. This item is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring.

·

A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring.

·

Example:

When the engine is determined to be misfiring, Misfire Margin = -128 to 0%.



Various Vehicle Conditions 5 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Engine Speed (Starter Off) Engine speed when starter off Min.: 0 rpm, Max.: 51199 rpm - -
·

Stored as Freeze Frame Data: Yes

·

This is the engine speed immediately after the engine is started.


Starter Count Number of times starter turned on after engine switch turned on (IG) Min.: 0, Max.: 255 - -
·

Stored as Freeze Frame Data: Yes

·

Indicates the number of times starter turned on in the current driving cycle.

·

Number of times starter turned on before engine started displayed in the 1 position.

·

Number of times starter turned on after engine started displayed in the 10 position.


Example:
If "21" is displayed on the GTS, the starter was turned on 1 time before engine start and turned on 2 times after engine start. (The maximum value for each counter is 9 times before engine start and 11 times after engine start)
Run Dist of Previous Trip Distance driven during previous trip Min.: 0 km (0 mile), Max.: 655.35 km (407.23 mile) - -
·

Stored as Freeze Frame Data: Yes

·

Before 5 seconds elapse after starting the engine, which is the detection duration of DTC P1604 (Startability Malfunction), this parameter indicates the distance driven during the previous trip.

·

After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.


HINT:

Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when DTCs other than P1604 were stored, the value indicates the distance driven during the current trip.



Rough Idle (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Rough Idle Status Status of the rough idle status Normal, Misfire, Continuous poor combustion, Intermittent poor combustion, Low frequency poor combustion Normal -
·

Stored as Freeze Frame Data: Yes

·

The following list of statuses indicates the degree and frequency of rough idling from highest to lowest.

Use this as a reference when trying to reproduce the rough idling.


1.

Misfire

2.

Continuous poor combustion

3.

Intermittent poor combustion

4.

Low frequency poor combustion


Plural Cylinders Rough Idle Status of the plural cylinders rough idle ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Indicates multiple cylinders are the cause of rough idling when ON.


Rough Idle #1 Status of the rough idle #1 ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Indicates speed has dropped compared to other cylinders and idling is rough for the indicated cylinder when ON.

·

This item indicates cylinders which are likely to be the cause of rough idle.


Rough Idle #2 Status of the rough idle #2 ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Same as Rough Idle #1


Rough Idle #3 Status of the rough idle #3 ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Same as Rough Idle #1


Rough Idle #4 Status of the rough idle #4 ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Same as Rough Idle #1


Rough Idle #5 Status of the rough idle #5 ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Same as Rough Idle #1


Rough Idle #6 Status of the rough idle #6 ON or OFF OFF -
·

Stored as Freeze Frame Data: Yes

·

Same as Rough Idle #1



Various Vehicle Conditions 6 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Engine Starting Time Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm) Min.: 0 ms, Max.: 655350 ms - -
·

Stored as Freeze Frame Data: Yes

·

This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm.

·

This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms.


Previous Trip Coolant Temp Engine coolant temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
·

Stored as Freeze Frame Data: Yes

·

Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip.

·

After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip.


Previous Trip Intake Temp Intake air temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
·

Stored as Freeze Frame Data: Yes

·

Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip.

·

After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip.


Engine Oil Temperature Engine oil temperature (estimated temperature) Min.: -40°C (-40°F), Max.: 215°C (419°F) - - Stored as Freeze Frame Data: Yes
Previous Trip Eng Oil Temp Engine oil temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) - - Stored as Freeze Frame Data: Yes
Ambient Temp for A/C Ambient temperature for A/C Min.: -40°C (-40°F), Max.: 215°C (419°F) - - Stored as Freeze Frame Data: Yes
Previous Trip Ambient Temp Ambient temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) - - Stored as Freeze Frame Data: Yes
Engine Start Hesitation History of hesitation during engine start ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

This value changes to ON when the engine speed does not reach 500 rpm during cranking.


Low Rev for Eng Start History of low engine speed after engine start ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

This item changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine.


Fuel Cut Elps Time Time elapsed after engine runs at high speed Min.: 0 sec, Max.: 68746 sec - -
·

Stored as Freeze Frame Data: Yes

·

The time elapsed after a fuel cut after high engine speed has occurred (More than the engine speed at which fuel cut occurs + 500 rpm).


ACM Vacuum switching valve (for active control engine mount) duty control Min.: 0%, Max.: 255% - - Stored as Freeze Frame Data: Yes
Electric Fan Motor Electric fan motors operation status ON or OFF - - Stored as Freeze Frame Data: Yes
Brake Override System Brake override system status ON or OFF ON: Brake override system operating - Stored as Freeze Frame Data: Yes
Idle Fuel Cut Fuel cut at idle ON or OFF ON: Fuel cut operating -
·

Stored as Freeze Frame Data: Yes

·

Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high.


FC TAU Fuel cut TAU (fuel cut during very light load) ON or OFF ON: Fuel cut operating -
·

Stored as Freeze Frame Data: Yes

·

This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete.


Immobiliser Fuel Cut Status of immobiliser fuel cut ON or OFF - - Stored as Freeze Frame Data: Yes
Immobiliser Fuel Cut History Immobiliser fuel cut history ON or OFF - -
·

Stored as Freeze Frame Data: Yes

·

When DTC P1604 is output and Immobiliser Fuel Cut History indicates ON, the engine could not start due to engine immobiliser operation.


Communication with ECT Status of communication with TCM Comm or No Comm - - Stored as Freeze Frame Data: Yes
Electrical Load Signal 1 Electrical load signal ON or OFF - - Stored as Freeze Frame Data: Yes

Various Vehicle Conditions 7 (Vehicle Information)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Model Code Model code - - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the model code: GSV50#


Engine Type Engine type - - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the engine type: 2GRFE


Cylinder Number Number of cylinders Min.: 0, Max.: 255 - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the number of cylinders: 6


Transmission Type Transmission (transaxle) type - - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the transaxle type: ECT 6th


Transmission Type2 Transmission (transaxle) type - NA -
·

Stored as Freeze Frame Data: No

·

Unused


Destination Destination - - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the destination: W


Model Year Model year Min.: 1900, Max.: 2155 - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the model year: 201#


System Identification System identification - - -
·

Stored as Freeze Frame Data: No

·

Used for identifying the engine system: Gasoline (gasoline engine)



Compression (Compression)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Engine Speed of Cyl #1 Engine speed for No. 1 cylinder Min.: 0 rpm, Max.: 51199 rpm - Results of real-vehicle check when performing the Active Test with a normal vehicle:
Engine Speed of Cyl #1: 257 rpm
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.

·

This is the engine speed of No. 1 cylinder measured during the fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed of Cyl #2 Engine speed for No. 2 cylinder Min.: 0 rpm, Max.: 51199 rpm - Results of real-vehicle check when performing the Active Test with a normal vehicle:
Engine Speed of Cyl #2: 256 rpm
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.

·

This is the engine speed of No. 2 cylinder measured during the fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed of Cyl #3 Engine speed for No. 3 cylinder Min.: 0 rpm, Max.: 51199 rpm - Results of real-vehicle check when performing the Active Test with a normal vehicle:
Engine Speed of Cyl #3: 257 rpm
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.

·

This is the engine speed of No. 3 cylinder measured during the fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed of Cyl #4 Engine speed for No. 4 cylinder Min.: 0 rpm, Max.: 51199 rpm - Results of real-vehicle check when performing the Active Test with a normal vehicle:
Engine Speed of Cyl #4: 256 rpm
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.

·

This is the engine speed of No. 4 cylinder measured during the fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed of Cyl #5 Engine speed for No. 5 cylinder Min.: 0 rpm, Max.: 51199 rpm - Results of real-vehicle check when performing the Active Test with a normal vehicle:
Engine Speed of Cyl #5: 257 rpm
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.

·

This is the engine speed of No. 5 cylinder measured during the fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed of Cyl #6 Engine speed for No. 6 cylinder Min.: 0 rpm, Max.: 51199 rpm - Results of real-vehicle check when performing the Active Test with a normal vehicle:
Engine Speed of Cyl #6: 256 rpm
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.

·

This is the engine speed of No. 6 cylinder measured during the fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Av Engine Speed of All Cyl Average engine speed for all cylinders Min.: 0 rpm, Max.: 51199 rpm - -
·

Stored as Freeze Frame Data: No

·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed.



Automatic Transaxle 1 (All Data)


Refer to Automatic Transaxle System.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Received MIL from ECT MIL status from ECT ON or OFF ON: MIL ON - Stored as Freeze Frame Data: Yes

Automatic Transaxle 2 (AT)


Refer to Automatic Transaxle System.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
Shift Position Sig from ECT Shift position signal from ECT - Actual shift position - Stored as Freeze Frame Data: Yes
A/T Oil Temp from ECT ATF temperature from ECT Min.: -40°C (-40°F), Max.: 215°C (419°F) With engine cold: Equal to ambient temperature - Stored as Freeze Frame Data: Yes

Automatic Transaxle 3 (All Data)


Refer to Automatic Transaxle System.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
SPD (NO) Output shaft speed Min.: 0 rpm, Max.: 12750 rpm - - Stored as Freeze Frame Data: Yes
SPD (NT) Input turbine speed Min.: 0 rpm, Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Input turbine speed (NT) is equal to engine speed

·

Lock-up off (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed


- Stored as Freeze Frame Data: Yes

Automatic Transaxle 4 (AT)


Refer to Automatic Transaxle System.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Reference Value Diagnostic Note
ECT Lock Up Lock-up status ON or OFF ON: Lock-up operating - Stored as Freeze Frame Data: Yes
SPD (NC) Counter gear speed Min.: 0 rpm, Max.: 12750 rpm - - Stored as Freeze Frame Data: Yes
Overdrive Cut Switch #1 Overdrive cut switch status ON or OFF - - Stored as Freeze Frame Data: Yes
Shift SW Status (P Range) Park/Neutral position switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


-
·

Stored as Freeze Frame Data: Yes

·

When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.


HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Shift SW Status (R Range) Park/Neutral position switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
·

Stored as Freeze Frame Data: Yes

·

When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.


HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Shift SW Status (N Range) Park/Neutral position switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


-
·

Stored as Freeze Frame Data: Yes

·

When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.


HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


Shift SW Status (N,P Range) Supported Status of park/neutral position switch (N or P) supported Unsupp or Supp - - Stored as Freeze Frame Data: Yes
Shift SW Status (N,P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in N or P

·

OFF: Shift lever not in N or P


- Stored as Freeze Frame Data: Yes
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Continuously shift to "+" (up-shift)

·

OFF: Release "+" (up-shift)


- Stored as Freeze Frame Data: Yes
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Continuously shift to "-" (down-shift)

·

OFF: Release "-" (down-shift)


- Stored as Freeze Frame Data: Yes
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


- Stored as Freeze Frame Data: Yes
Shift SW Status (D Range) Park/Neutral position switch status ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


-
·

Stored as Freeze Frame Data: Yes

·

When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.


HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705*.


*: Refer to DTC P0705.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0705


ACTIVE TEST


HINT:
·

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

·

As DTCs may be stored when an Active Test or learning is performed, make sure to clear the DTCs before returning the vehicle to the customer.



a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Injection Volume Control the injection volume Between -12.5% and 24.8%
·

All fuel injector assemblies are tested at the same time.

·

Perform the test at 3000 rpm or less.

·

Injection volume can be changed in fine gradations within the control range.

·

Control the Injection Volume enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.

·

To conduct the test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

·

During the Active Test, air fuel ratio feedback control and feedback learning are stopped.


Control the Injection Volume for A/F Sensor Change injection volume -12.5%/0%/12.5%
·

All fuel injector assemblies are tested at the same time.

·

Perform the test at 3000 rpm or less.

·

Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.

·

To conduct the test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

·

During the Active Test, air fuel ratio feedback control and feedback learning are stopped.

·

See waveform *2.


Activate the VSV for Intake Control Activate intake air control valve assembly ON/OFF
·

Perform this test with the engine switch on (IG).

·

This test activates intake air control valve assembly only 10 seconds.


Activate the VSV for Evap Control Activate purge VSV control ON/OFF
·

The purge VSV is opened with a 30% duty ratio.

·

See waveform *4.


Control the Fuel Pump / Speed Activate fuel pump ON/OFF Perform this test when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is stopped.

·

Shift lever in P.


Control the Fuel Pump Duty Activate fuel pump 25% or 80% Perform this test is possible when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is running.

·

Shift lever in P.


Control the ACM Inhibit Activate vacuum switching valve (for active control engine mount) ON/OFF Perform this test when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is stopped.

·

Shift lever in P.


Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.

·

Perform this test when the following conditions are met:

·

Engine switch is on (IG).

·

Engine is stopped.

·

Shift lever in P.



Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF Perform this test when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is stopped.

·

Shift lever in P.


Control the Electric Cooling Fan Control electric cooling fan motor ON/OFF Perform this test when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is stopped.

·

Shift lever in P.


Control the ETCS Open/Close Slow Speed Throttle actuator Close/Open
Open: Throttle valve opens slowly
Perform this test when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is stopped.

·

Accelerator pedal is fully depressed (accelerator pedal position: 58 degrees or more).

·

Shift lever in P.


Control the ETCS Open/Close Fast Speed Throttle actuator Close/Open
Open: Throttle valve opens quickly
·

Same as above.

·

See waveform *3.


Control the VVT Linear (Bank1) Control camshaft timing oil control valve assembly (for intake camshaft of bank 1) -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.

·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.

·

See waveform *5.


Control the VVT System (Bank1) Turn camshaft timing oil control valve assembly (for intake camshaft of bank 1) on and off ON/OFF
ON: VVT OCV Duty #1 100%
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly (for intake camshaft of bank 1) is turned on.

·

Engine runs and idles normally when the camshaft timing oil control valve assembly (for intake camshaft of bank 1) is off.

·

Perform this test when the following conditions are met:

·

Engine is idling.

·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Linear (Bank2) Control camshaft timing oil control valve assembly (for intake camshaft of bank 2) -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.

·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT System (Bank2) Turn camshaft timing oil control valve assembly (for intake camshaft of bank 2) on and off ON/OFF
ON: VVT OCV Duty #2 100%
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly (for intake camshaft of bank 2) is turned on.

·

Engine runs and idles normally when the camshaft timing oil control valve assembly (for intake camshaft of bank 2) is off.

·

Perform this test when the following conditions are met:

·

Engine is idling.

·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the VVT Exhaust Linear (Bank1) Control camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum retard
-100%: Maximum advance
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.

·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.

·

See waveform *6.


Control the VVT Exhaust Linear (Bank2) Control camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum retard
-100%: Maximum advance
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

·

Engine is idling.

·

Shift lever in P.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Activate the VSV for AICS Activate vacuum switching valve (for air intake control valve) ON/OFF Perform this test when the following conditions are met:
·

Engine switch is on (IG).

·

Engine is stopped.

·

Shift lever in P.


Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #6) injector fuel cut
·

#1/#2/#3/#4/#5/#6

·

ON/OFF


Perform this test when the following conditions are met:
·

Vehicle is stopped.

·

Engine is idling.

·

Shift lever in P.


Control the All Cylinders Fuel Cut Fuel cut for all cylinders ON/OFF Perform this test when the following conditions are met:
·

Vehicle is stopped.

·

Engine is idling.

·

Shift lever in P.


Check the Cylinder Compression Check the cylinder compression pressure ON/OFF Fuel injection and ignition stop in all cylinders.
*1
HINT:

*1:

In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the engine switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the engine switch on (IG).

5.

Turn the GTS on.

6.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.


7.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


8.

While the engine is not running, press the Active test button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.


9.

Crank the engine for about 10 seconds.

HINT:

Continue to crank the engine until the values change from the default value (51199 rpm).


10.

Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the GTS.

NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.

·

Use a fully-charged battery.



HINT:

At first, the GTS displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.


11.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.


12.

Push the snapshot button to turn the snapshot function off.

13.

Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.

HINT:

If the data is not displayed as a graph, the change of the values cannot be observed.


14.

Check the change in engine speed values.

HINT:

As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.





Reference Waveforms for Active Test
·

*2: Control the Injection Volume for A/F Sensor (Idling after warming up)

A285266E13
1.083,0.76 1.76,1.115 0.677,0.354 10 false 12.5% 2.594,0.75 3.271,1.104 0.677,0.354 10 false -12.5% 0.167,3.083 1.688,3.396 1.521,0.313 10 false AFS Voltage B1S1 [V] 0.167,5.688 1.688,6 1.521,0.313 10 false O2S B1S2 [V] 2.729,6 3.583,6.313 0.854,0.313 10 false Time Delay 4.417,6 5.271,6.313 0.854,0.313 10 false Time Delay 1.729,6.583 2.583,6.896 0.854,0.313 10 false Rich 1.729,7.49 2.583,7.802 0.854,0.313 10 false Lean 0.646,7.938 1.5,8.25 0.854,0.313 10 false 10 seconds 3.563,7.854 3.833,8.083 0.271,0.229 10 false A 5.448,7.854 5.719,8.083 0.271,0.229 10 false B 0.25,6.521 0.75,6.75 0.5,0.229 10 false 0.9 V 0.25,7.604 0.688,7.833 0.438,0.229 10 false 0.7 V 5.438,5.052 5.708,5.281 0.271,0.229 10 false B 3.573,5.052 3.844,5.281 0.271,0.229 10 false A 1.729,4.635 2.583,4.948 0.854,0.313 10 false Rich 1.729,3.75 2.583,4.063 0.854,0.313 10 false Lean 0.25,4.802 0.75,5.031 0.5,0.229 10 false 2.2 V 0.25,3.688 0.75,3.917 0.5,0.229 10 false 4.0 V 0.167,0.188 3.167,0.5 3,0.313 10 false Control the Injection Volume for A/F Sensor 4.156,0.75 4.833,1.104 0.677,0.354 10 false 12.5% 5.583,0.75 6.26,1.104 0.677,0.354 10 false -12.5%

HINT:

During the Active Test, air fuel ratio feedback control and feedback learning are stopped.


GTS Display Measurement Item Normal Condition
Control the Injection Volume for A/F Sensor - ▲A ▲B
Active Test operation -12.5% 12.5%
AFS Voltage B1S1 3.878 V 2.648 V
O2S B1S2 0.760 V 0.875 V

HINT:
·

Usually, the value of AFS Voltage B1S1 drops below 3.1 V when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.

·

Usually, the value of AFS Voltage B1S1 changes to 3.4 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.

·

Usually, the value of O2S B1S2 changes to 0.55 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.

·

Usually, the value of O2S B1S2 drops below 0.4 V when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



·

*3: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Engine switch on (IG))

A306376E24
0.427,5.667 0.51,5.667 false 0.427,7.396 0.51,7.396 false 0.167,0.646 6.896,0.844 6.729,0.198 10 false Throttle Position Command [V] (Target Value) 0.156,1.25 1.75,1.51 1.594,0.26 10 false 5 V 0.156,1.958 1.75,2.219 1.594,0.26 10 false 0 V 0.146,3.156 1.74,3.417 1.594,0.26 10 false 5 V 0.156,3.802 1.75,4.063 1.594,0.26 10 false 0 V 0.177,2.719 6.906,2.917 6.729,0.198 10 false Throttle Position No.1 [V] (Actual Value) 4.458,2.208 4.75,2.448 0.292,0.24 10 false A 5.583,2.208 5.875,2.448 0.292,0.24 10 false B 4.448,4.042 4.74,4.281 0.292,0.24 10 false A 5.594,4.052 5.885,4.292 0.292,0.24 10 false B 0.177,4.604 6.906,4.802 6.729,0.198 10 false Throttle Motor Duty (Open) [%] 0.042,4.958 1.635,5.219 1.594,0.26 10 false 30.0% 0.094,5.594 0.479,5.792 0.385,0.198 10 false 0.0% 4.458,5.875 4.75,6.115 0.292,0.24 10 false A 4.458,7.615 4.75,7.854 0.292,0.24 10 false A 5.594,5.885 5.885,6.125 0.292,0.24 10 false B 5.604,7.625 5.896,7.865 0.292,0.24 10 false B 0.104,7.323 1.698,7.583 1.594,0.26 10 false 0.0% 0.031,6.823 1.625,7.083 1.594,0.26 10 false 30.0% 0.281,6.417 7.01,6.615 6.729,0.198 10 false Throttle Motor Duty (Close) [%] 3.594,0.979 3.979,1.198 0.385,0.219 10 false Open 5.865,0.99 6.25,1.208 0.385,0.219 10 false Open 1.708,0.979 2.094,1.198 0.385,0.219 10 false Close 4.865,0.979 5.25,1.198 0.385,0.219 10 false Close

HINT:
·

Usually, Throttle Position Command (Target Value) and Throttle Position No. 1 (Actual Value) are almost the same.

·

If any DTCs related to the Electronic Throttle Control System (ETCS) are stored, this Active Test does not function.



GTS Display Measurement Item Normal Condition
Control the ETCS Open/Close Fast Speed - ▲A ▲B
Active Test operation Open Close
Throttle Position Command 2.597 V 0.820 V
Throttle Position No. 1 2.597 V 0.820 V
Throttle Motor Duty (Open) 13.0% 0.0%
Throttle Motor Duty (Close) 0.0% 15.0%

·

*4: Activate the VSV for Evap Control (Idling after warming up)

A308157E22
0.427,3.948 0.51,3.948 false 0.146,0.25 3.208,0.448 3.063,0.198 10 false EVAP (Purge) VSV [%] 0.219,1.573 0.5,1.813 0.281,0.24 10 false 20 0.292,1.99 0.594,2.188 0.302,0.198 10 false 0 2.156,2.313 2.458,2.51 0.302,0.198 10 false A 3.708,2.302 4.01,2.5 0.302,0.198 10 false B 2.156,4.781 2.458,4.979 0.302,0.198 10 false A 3.719,4.781 4.021,4.979 0.302,0.198 10 false B 0.104,3.865 0.438,4.031 0.333,0.167 10 false 2300 0.094,4.542 0.76,4.792 0.667,0.25 10 false 2000 0.167,3.458 3.229,3.656 3.063,0.198 10 false Injector (Port) [μs] 0.146,6.323 3.208,6.521 3.063,0.198 10 false AFS Voltage B1S1 [V] 0.188,6.75 0.469,6.99 0.281,0.24 10 false 3.4 0.177,7.302 0.458,7.542 0.281,0.24 10 false 3.2 2.156,7.542 2.458,7.74 0.302,0.198 10 false A 3.656,7.531 3.958,7.729 0.302,0.198 10 false B 0.542,7.573 3.604,7.771 3.063,0.198 10 false 6 seconds 1.156,1.167 1.531,1.365 0.375,0.198 10 false ON 4.229,1.167 4.604,1.365 0.375,0.198 10 false ON 2.885,1.167 3.26,1.365 0.375,0.198 10 false OFF 5.885,1.177 6.26,1.375 0.375,0.198 10 false OFF

GTS Display Measurement Item Normal Condition
Activate the VSV for Evap Control - ▲A ▲B
Active Test operation ON OFF
EVAP (Purge) VSV 29.8% 0.0%
Injector (Port) 2127 μs 2190 μs
AFS Voltage B1S1 3.356 V 3.234 V

HINT:
·

Even when the Active Test is performed (the purge VSV is opened approximately 30%), the ECM performs air fuel ratio feedback to maintain the air fuel ratio at the stoichiometric ratio. Therefore, by observing the change in the Data List item "Injector (Port)", it is possible to determine whether the purge VSV is actually open.

·

The graphs and values above are for reference only because the fuel injection volume (compensation volume) varies depending on the HC density of the purge air from the canister.



·

*5: Control the VVT Linear (Bank 1)

A283607E13
0.719,7.333 0.802,7.333 false 0.729,5.719 0.813,5.719 false 0.729,6.365 0.813,6.365 false 0.167,0.229 2.25,0.563 2.083,0.333 10 false Control the VVT Linear (Bank 1) 0.167,1.885 2.25,2.219 2.083,0.333 10 false Engine Speed [rpm] 0.167,3.573 2.25,3.906 2.083,0.333 10 false VVT Change Angle #1 [DegFR] 0.167,5.281 1.75,5.531 1.583,0.25 10 false VVT OCV Duty #1 [%] 0.167,6.896 1.75,7.146 1.583,0.25 10 false VVT Aim Angle #1 [%] 1.25,0.76 1.677,1 0.427,0.24 10 false 15% 3.917,0.75 4.344,0.99 0.427,0.24 10 false 15% 2.656,1.333 3.083,1.573 0.427,0.24 10 false -15% 4.823,1.333 5.25,1.573 0.427,0.24 10 false -15% 0.385,2.229 0.896,2.479 0.51,0.25 10 false 1000 0.458,3.219 0.958,3.469 0.5,0.25 10 false 500 0.406,3.906 0.823,4.156 0.417,0.25 10 false 56.0 0.5,4.813 0.917,5.063 0.417,0.25 10 false 0.0 0.406,6.292 0.823,6.542 0.417,0.25 10 false 31.8 0.5,8.083 0.917,8.333 0.417,0.25 10 false 0.0 0.417,7.25 0.833,7.5 0.417,0.25 10 false 46.8 0.417,5.646 0.833,5.896 0.417,0.25 10 false 61.8 4.021,8.427 5.104,8.677 1.083,0.25 10 false 5 seconds 1.74,8.396 1.99,8.646 0.25,0.25 10 false A 2.896,8.385 3.146,8.635 0.25,0.25 10 false B 1.74,6.708 1.99,6.958 0.25,0.25 10 false A 1.74,5.125 1.99,5.375 0.25,0.25 10 false A 2.896,6.708 3.146,6.958 0.25,0.25 10 false B 2.896,5.125 3.146,5.375 0.25,0.25 10 false B

GTS Display Measurement Item Normal Condition
Control the VVT Linear (Bank 1) - ▲A ▲B
Active Test operation* 15% -15%
VVT Change Angle #1 54.9 DegFR 0.0 DegFR
VVT OCV Duty #1 61.8% 31.8%
VVT Aim Angle #1 46.8% 46.8%

HINT:
·

*: Change the control value for Control the VVT Linear to 15% or -15%.

·

The Control the VVT Linear Active Test considers the value of VVT Aim Angle #1 to be 0 and raises or lowers the duty ratio with respect to VVT Aim Angle #1.

·

The sum of the control value for the Control the VVT Linear Active Test and the value of VVT Aim Angle #1 is approximately equal to the value of VVT OCV Duty #1.

·

When the control value for the Control the VVT Linear Active Test is changed a few times, there should not be a large discrepancy between VVT OCV Duty #1 when the system starts advancing or retarding the timing and the rate of change of VVT Change Angle #1.



·

*6: Control the VVT Exhaust Linear (Bank 1)

A283608E26
0.594,5.771 0.698,5.771 false 0.615,7.385 0.698,7.385 false 0.583,6.292 0.698,6.292 false 0.167,0.188 2.75,0.438 2.583,0.25 10 false Control the VVT Exhaust Linear (Bank 1) 0.167,1.917 1.583,2.167 1.417,0.25 10 false Engine Speed [rpm] 0.167,3.594 2.167,3.844 2,0.25 10 false VVT Ex Chg Angle #1 [DegFR] 0.167,5.313 2.083,5.563 1.917,0.25 10 false VVT Ex OCV Duty #1 [%] 0.167,6.917 2.083,7.167 1.917,0.25 10 false VVT Ex Hold Lrn Val #1 [%] 1.115,0.667 1.615,0.917 0.5,0.25 10 false 15% 2.667,0.667 3.167,0.917 0.5,0.25 10 false 15% 4.833,0.667 5.333,0.917 0.5,0.25 10 false 15% 1.854,1.208 2.354,1.458 0.5,0.25 10 false -15% 3.625,1.208 4.125,1.458 0.5,0.25 10 false -15% 5.865,1.208 6.365,1.458 0.5,0.25 10 false -15% 0.302,2.219 0.802,2.469 0.5,0.25 10 false 1000 0.385,3.104 0.885,3.354 0.5,0.25 10 false 500 0.323,3.906 0.75,4.156 0.427,0.25 10 false 35.0 0.396,4.698 0.729,4.948 0.333,0.25 10 false 0.0 0.281,6.208 0.615,6.458 0.333,0.25 10 false 35.8 0.406,8.042 0.74,8.292 0.333,0.25 10 false 0.0 0.281,5.688 0.708,5.938 0.427,0.25 10 false 66.0 0.323,7.302 0.75,7.552 0.427,0.25 10 false 50.8 2.885,8.333 3.135,8.583 0.25,0.25 10 false A 4.052,8.333 4.302,8.583 0.25,0.25 10 false B 4.052,6.646 4.302,6.896 0.25,0.25 10 false B 4.052,5.01 4.302,5.26 0.25,0.25 10 false B 2.885,6.646 3.135,6.896 0.25,0.25 10 false A 2.885,5.01 3.135,5.26 0.25,0.25 10 false A 5,8.375 5.75,8.625 0.75,0.25 10 false 8 seconds

GTS Display Measurement Item Normal Condition
Control the VVT Exhaust Linear (Bank 1) - ▲A ▲B
Active Test operation* 15% -15%
VVT Ex Chg Angle #1 34.6 DegFR 0.0 DegFR
VVT Ex OCV Duty #1 65.8% 35.8%
VVT Ex Hold Lrn Val #1 50.8% 50.8%

HINT:
·

*: Change the control value for Control the VVT Exhaust Linear to 15% or -15%.

·

The Control the VVT Exhaust Linear Active Test considers the value of VVT Ex Hold Lrn Val #1 to be 0 and raises or lowers the duty ratio with respect to VVT Ex Hold Lrn Val #1.

·

The sum of the control value for the Control the VVT Exhaust Linear Active Test and the value of VVT Ex Hold Lrn Val #1 is approximately equal to the value of VVT Ex OCV Duty #1.

·

When the control value for the Control the VVT Exhaust Linear Active Test is changed a few times, there should not be a large discrepancy between VVT Ex OCV Duty #1 when the system starts advancing or retarding the timing and the rate of change of VVT Ex Chg Angle #1.