Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0076674 AUTOMATIC TRANSAXLE SYSTEM U

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph),
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed Min.: 0 rpm,
Max.: 16383.75 rpm
600 to 700 rpm: Idling When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Calculate Load Calculated load by ECM Min.: 0.0%,
Max.: 100.0%
·

Ignition switch ON: 0.0%

·

Idling (warm up the engine): 23.5%

·

Running without load (3000 rpm): 22.3%

·

Vehicle driven at constant speed of 60 km/h (37 mph): 59.6%


This is the engine load calculated based on the estimated intake manifold pressure.
Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%)
(For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)
Coolant Temp Engine coolant temperature Min.: -40°C (-40 °F),
Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up
·

If value -40°C(-40°F): sensor circuit open

·

If value 140°C (284°F): sensor circuit shorted


Intake Air Intake air temperature Min.: -40 °C (-40 °F),
Max.: 215 °C (419 °F)
Equivalent to ambient air temperature
·

If value -40°C(-40°F): sensor circuit open

·

If value 140°C (284°F): sensor circuit shorted


Engine Run Time Engine run time Min.: 0 s
Max.: 65535 s
Time after engine start This is the time elapsed since theengine started.
HINT:

The time is counted only while theengine is running.


Battery Voltage Battery voltage Min.: 0, Max.: 65.535 V 11 to 14 V: Idling -
Throttle Sensor Volt % Throttle position sensor output Min.: 0.0%, Max.: 100.0% 10 to 22%: Idling Calculated value based on VTA1
Starter Signal Starter signal Open or Close Open: Starter operating
Close: Starter not operating
-
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever is in P or N

·

OFF: Shift lever is not in P or N


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Stop Light Switch Stop light switch status ON or OFF Brake pedal is
·

ON: Depressed

·

OFF: Released


-
TC Terminal TC Terminal Status ON or OFF - -
# Codes(Include History) # of Codes Min.: 0, Max.: 255 - Number of detected DTCs
MIL ON Run Distance MIL ON run distance Min.: 0 km (0 mile),
Max.: 65535 km (40723 mile)
Distance after DTC detected This is the distance driven after a DTC is stored.
Running Time from MIL ON Running time from MIL ON Min.: 0 min,
Max.: 65535 min,
Equivalent to running time after MIL ON -
Time after DTC Cleared Time after DTC cleared Min.: 0 min,
Max.: 65535 min,
Equivalent to time after DTCs cleared This is the time elapsed afterDTCs were cleared (or after thevehicle left the factory). Timeelapsed after the ignition switch isturned off is not counted.
Distance from DTC Cleared Distance after DTC cleared Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Equivalent to time after DTCs cleared This is the distance driven after DTCs were cleared (or after the vehicle left the factory).
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared Min.: 0, Max.: 255 - Number of warm-up cycles after DTCs cleared
TC and TE1 TC and TE1 terminals of DLC3 ON or OFF - Active Test support data
Transmission Type2 [NA] - - -
Throttle Position from EFI Throttle sensor position Min.: 0.0%, Max.: 100.0% - Recognition value for throttle opening angle on ECM
Accel Position from EFI Absolute Accelerator Pedal Position Min.: 0.0%, Max.: 100.0% - -
SPD (NT) Input turbine speed Min.: 0 rpm, Max.: 12750 rpm Lock-up is
·

ON (After warming up the engine):

Input turbine speed (NT) is equal to engine speed

·

OFF (idling with shift lever in N):

Input turbine speed (NT) is nearly equal to engine speed


Data is displayed in increments of 50 rpm
SPD (NC) Counter gear speed Min.: 0 rpm, Max.: 12750 rpm - Data is displayed in increments of 50 rpm
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever is in P

·

OFF: Shift lever is not in P


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever is in R

·

OFF: Shift lever is not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status ON or OFF
·

ON: Shift lever is in N

·

OFF: Shift lever is not in N


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Continuously shift to "+" (up-shift)

·

OFF: Release "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Continuously shift to "-" (down-shift)

·

OFF: Release "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status ON or OFF Shift lever is:
·

ON: S, "+" or "-"

·

OFF: Not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever is in D or S

·

OFF: Shift lever is not in D or S


When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
A/T Oil Temperature 1 ATF temp. sensor value min.: -40 °C (-40 °F)
max.: 215 °C (419 °F)
·

After stall test;

Approx. 80°C (176°F)

·

Equal to ambient temperature when cold soak


If the value is "-40°C (-40°F)" or "150°C (302°F)", ATF temp. sensor circuit is open or shorted.
NT Sensor Voltage Input speed sensor NT output voltage Min.: 0.000 V, Max.: 5.000 V 0.1 to 1.9 V -
NC Sensor Voltage Output speed sensor NC output voltage Min.: 0.000 V, Max.: 5.000 V 0.1 to 1.9 V -
TPS 3 Switch ATF pressure switch No. 3 status 0: OFF / 1: ON
·

ON: Shift solenoid valve SLU is ON

·

OFF: Shift solenoid valve SLU is OFF


-
Lock Up Lock up 0: OFF / 1: ON Lock up: ON -
Shift Status TCM gear shift command 1st, 2nd, 3rd, 4th, 5th or 6th Same as actual gear -
SLT Solenoid Status Shift solenoid SLT status ON or OFF Shift solenoid SLT is
·

Operating: ON

·

Not operating: OFF


-
SLU Solenoid Status Shift Solenoid SLU Status ON or OFF Shift solenoid SLU is
·

Operating: ON

·

Not operating: OFF


-
SL Solenoid Status Shift Solenoid SL Status ON or OFF Shift solenoid SL is
·

Operating: ON

·

Not operating: OFF


-
HINT:
Tester Display Diagnostic Note
Neutral Position SW Signal When the failure still occurs even after adjusting these parts, Click here(Click here)
Shift SW Status (P Range) When the failure still occurs even after adjusting these parts, Click here(Click here)
Shift SW Status (R Range) When the failure still occurs even after adjusting these parts, Click here(Click here)
Shift SW Status (N Range) When the failure still occurs even after adjusting these parts, Click here(Click here)
Shift SW Status (D Range) When the failure still occurs even after adjusting these parts, Click here(Click here)




ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the intelligent tester, perform the Active Test.

Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Connect the TC and TE1 Connects and disconnects TC and TE1.
(transitions into the fluid temperature detection mode)
ON/OFF The MIL will not blink when "Connect the TC and TE1 / ON" is selected.
Activate the Solenoid (SLU) Operates shift solenoid SLU ON/OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (SLT) Operates shift solenoid SLT to raise the line pressure. ON/OFF
HINT:

ON: No action (normal operation)

OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the TCM commands the SLT solenoid to turn off).


[Vehicle Condition]
·

Vehicle Stopped

·

IDL: ON


Activate the Lock Up Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition. ON/OFF Can be used to check SLU and SL solenoid operation.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 20%

·

Vehicle speed:60 km/h (37 mph) or more, and 6th gear


Activate the Solenoid (SL) Operates shift solenoid SL ON/OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Control the Shift Position Operates the shift solenoid valves to allow gears to selected manually.
·

Press "→" button: Upshift occurs

·

Press "←" button: Downshift occurs


Can be used to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
Do not downshift at high speeds. Doing so will damage the automatic transaxle.
[Vehicle Condition]

50 km/h (31 mph) or less


Activate the Solenoid (SL1) Operates shift solenoid SL1 ON/OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (SL2) Operates shift solenoid SL2 ON/OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (SL3) Operates shift solenoid SL3 ON/OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (SL4) Operates shift solenoid SL4 ON/OFF [Vehicle Condition]
·

Engine stopped

·

Shift lever in P or N


The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (See page Drivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST).

HINT:

Note that the pressure readings for the Active Test and Hydraulic Test are different.