Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM2030EQ _53 Suspension _052590 TIRE PRESSURE MONITORING _0265589 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Tire pressure warning system DTCs can be checked by connecting terminals 13 (TC) and 4 (CG) of the DLC3. The DTCs are indicated by blinking the tire pressure warning light.

WIRING DIAGRAM

C354518E04
0.719,3.573 2.635,3.813 1.917,0.24 10 false : CAN Communication Line 2.979,1.01 4.656,1.469 1.677,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 5.271,0.958 7,1.396 1.729,0.438 10 false Tire Pressure Warning ECU and Receiver 5.281,0.781 6.052,0.979 0.771,0.198 10 false N44 2.979,0.813 3.75,1.01 0.771,0.198 10 false I13 3.781,0.385 4.552,0.583 0.771,0.198 10 false PRG 4.198,0.281 4.969,0.479 0.771,0.198 10 false 4 5.781,0.292 6.552,0.49 0.771,0.198 10 false 5 5.969,0.385 6.74,0.583 0.771,0.198 10 false PRG2 1.104,2.344 1.875,2.542 0.771,0.198 10 false TC 0.552,2.865 1.323,3.063 0.771,0.198 10 false A25 0.854,2.865 1.625,3.063 0.771,0.198 10 false ECM 5.969,3.24 6.74,3.438 0.771,0.198 10 false I39 6.25,3.24 6.76,3.5 0.51,0.26 10 false DLC3 1.417,2.208 1.823,2.438 0.406,0.229 10 false 23 5.708,2.229 6.115,2.458 0.406,0.229 10 false 13 5.792,2.542 6.198,2.771 0.406,0.229 10 false 4 5.969,2.333 6.74,2.531 0.771,0.198 10 false TC 5.969,2.656 6.74,2.854 0.771,0.198 10 false CG

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK DTC (C2179/79)

B

2.CHECK DTC (C2179/79)

Result:
Result Proceed to
DTC C2179/79 is not output. A
DTC C2179/79 is output. B



A

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

B

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Disconnect the A25 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - A25-23 (TC) Always Below 1 Ω
I39-13 (TC) or A25-23 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C326026C27
1.542,0.521 1.948,0.781 0.406,0.26 1.604,1.885 1.229,1.313 true 1.667,0.563 1.979,0.76 0.313,0.198 10 false I39 1.073,1.115 1.385,1.313 0.313,0.198 10 false CG 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT DLC3 TERMINAL VOLTAGE (TC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT DLC3 TERMINAL VOLTAGE (TC VOLTAGE)
a.

Reconnect the A25 ECM connector.


b.
C326026C26
1.542,0.521 1.948,0.781 0.406,0.26 1.604,1.885 1.229,1.313 true 1.833,2.375 2.115,1.302 true 1.667,0.563 1.979,0.76 0.313,0.198 10 false I39 1.073,1.115 1.385,1.313 0.313,0.198 10 false CG 2.042,1.115 2.354,1.313 0.313,0.198 10 false TC 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a
*a Front view of DLC3


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I39-13 (TC) - I39-4 (CG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG