Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A263608E01
0.093,2.233 0.314,2.396 0.221,0.163 10 1.0 0.093,2.079 0.314,2.24 0.221,0.161 10 1.2 0.093,1.652 0.323,1.809 0.23,0.156 10 2.4 0.093,1.174 0.312,1.33 0.219,0.156 10 3.6 0.093,0.929 0.326,1.085 0.233,0.156 10 4.2 0.91,3.579 1.168,3.744 0.259,0.165 10 150 1.543,3.372 1.8,3.524 0.257,0.152 10 450 2.141,3.372 2.391,3.525 0.25,0.153 10 750 0.74,3.372 0.99,3.525 0.25,0.153 10 100 2.52,3.372 2.818,3.523 0.299,0.151 10 900 0.162,0.212 0.967,0.41 0.806,0.198 10 Voltage (V) 0.486,3.999 2.244,4.192 1.758,0.193 10 Manifold Absolute Pressure 2.489,3.585 3.232,3.786 0.743,0.201 10 mmHg(abs) 2.719,2.951 3.302,3.131 0.583,0.179 10 kPa(abs) 0.798,2.999 1.245,3.151 0.448,0.152 10 19.998 0.504,2.744 0.952,2.895 0.448,0.152 10 13.332 1.422,2.743 1.87,2.895 0.448,0.152 10 59.995 2.009,2.999 2.457,3.151 0.448,0.152 10 99.992 2.319,2.749 2.871,2.901 0.552,0.152 10 119.990

The manifold absolute pressure sensor detects the intake manifold pressure as a voltage using a built-in sensor. The ECM calculates intake manifold pressure based on this voltage and also calculates the EGR valve assembly and purge VSV opening amount according to changes in the intake manifold pressure, and detects errors in the pressure sensor using the changes in pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input The output voltage from the manifold absolute pressure sensor less than 0.5 V for 0.5 seconds (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input The output voltage from the manifold absolute pressure sensor higher than 4.5 V for 0.5 seconds (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the manifold absolute pressure using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.


Pressure Displayed Malfunction
Approximately 0 kPa(abs) [0 mmHg(abs)]
·

Short in PIM circuit to ground

·

Short in PIM circuit to E2 circuit

·

Open in VC circuit


130 kPa(abs) [975 mmHg(abs)] or higher
·

Short in VC circuit to PIM circuit

·

Open in PIM circuit

·

Open in E2 circuit



MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the manifold absolute pressure. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold absolute pressure sensor and stores a DTC.

Example:

When the sensor output voltage remains less than 0.5 V, or higher than 4.5 V for 0.5 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and wait 5 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0107 or P0108.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A259008E03
0.147,2.605 0.456,2.803 0.309,0.198 10 E25 0.14,2.773 2.38,2.922 2.24,0.149 10 Manifold Absolute Pressure Sensor 6.185,3.099 6.529,3.262 0.344,0.163 10 ECM 5.632,0.98 6.08,1.129 0.448,0.149 10 VCPM 5.877,3.099 6.159,3.248 0.281,0.149 10 E28 5.371,0.98 5.548,1.129 0.177,0.149 10 78 5.371,1.554 5.559,1.724 0.188,0.17 10 79 5.371,2.093 5.575,2.243 0.204,0.149 10 80 5.632,1.554 5.9,1.703 0.267,0.149 10 PIM 5.632,2.093 6.045,2.26 0.413,0.167 10 EPIM 1.366,0.98 1.592,1.129 0.226,0.149 10 VC 1.324,1.554 1.591,1.703 0.267,0.149 10 PIM 1.394,2.093 1.592,2.26 0.198,0.167 10 E2 1.664,0.98 1.771,1.15 0.108,0.17 10 3 1.664,1.554 1.764,1.724 0.101,0.17 10 2 1.664,2.093 1.785,2.257 0.122,0.163 10 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MAP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 234 4

e.

Read the MAP value.

OK:

Same value as the actual atmospheric pressure.



HINT:
·

Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)]. For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.
A248180C14
0.209,0.924 0.504,1.15 0.295,0.226 10 *a 0.539,2.046 0.938,2.306 0.4,0.26 0.586,2.087 0.873,2.235 0.287,0.148 10 E25 1.469,2.367 1.153,2.902 false 1.717,2.367 1.717,2.917 false 1.965,2.369 2.419,2.897 false 0.996,2.937 1.21,3.094 0.214,0.157 10 E2 1.563,2.937 1.862,3.081 0.3,0.145 10 PIM 2.339,2.931 2.569,3.076 0.23,0.145 10 VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E25-3 (VC) - E25-1 (E2) Power switch on (IG) 4.75 to 5.25 V
E25-2 (PIM) - E25-1 (E2) Power switch on (IG) 3.0 to 5.0 V



Result:
Proceed to
OK
NG



OK

3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>2AR-FXE EMISSION CONTROL>VACUUM SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (P0107 OR P0108)
4.CHECK WHETHER DTC OUTPUT RECURS (P0107 OR P0108)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG) and turn the tester on.


c.

Clear the DTC.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the power switch off and wait for at least 30 seconds.


e.

Turn the power switch on (IG).


f.

Turn the tester on.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.


i.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0107 or P0108 is output B




A

END

B

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E25-3 (VC) - E28-78 (VCPM) Always Below 1 Ω
E25-1 (E2) - E28-80 (EPIM) Always Below 1 Ω
E25-2 (PIM) - E28-79 (PIM) Always Below 1 Ω
E25-3 (VC) or E28-78 (VCPM) - Body ground Always 10 kΩ or higher
E25-2 (PIM) or E28-79 (PIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR