Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P261B  Engine Coolant Pump "B" Control Malfunction  P261C  Engine Coolant Pump "B" Control Circuit Low  P261D  Engine Coolant Pump "B" Control Circuit High  


DESCRIPTION

The ECM controls the engine water pump assembly by calculating the necessary amount of coolant flow based on engine coolant temperature, engine speed and vehicle speed information. The speed of the engine water pump assembly is controlled steplessly using a duty cycle signal sent from the ECM. This optimal control enhances warm-up performance and reduces cooling losses, thus reducing the specific fuel consumption of the engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P261B Engine Coolant Pump "B" Control Malfunction Engine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1 trip detection logic).
·

Open or short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


Comes on DTC stored
P261C Engine Coolant Pump "B" Control Circuit Low Engine water pump assembly output voltage is less than specified value while the engine water pump assembly is operating (1 trip detection logic).
·

Open or short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


Comes on DTC stored
P261D Engine Coolant Pump "B" Control Circuit High Engine water pump assembly output voltage is higher than specified value while the engine water pump assembly is operating (1 trip detection logic).
·

Short in engine water pump assembly circuit

·

Engine water pump assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM calculates the speed of the engine water pump assembly using a duty cycle signal sent from the engine water pump assembly. When the speed of the engine water pump assembly becomes less than 900 rpm while it is operating, the ECM detects the malfunction and stores DTC P261B.

The engine water pump assembly operates steplessly based on a duty cycle signal sent from the ECM. If actual drive duty cycle ratio does not correspond to the target drive duty cycle of the engine water pump assembly, the ECM detects the malfunction.

MONITOR STRATEGY

Required Sensors/Components Engine water pump assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).

8.

Idle the engine for 20 seconds or more [A].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P261B, P261C or P261D.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A268319E01
4.287,1.486 5.6,1.853 1.313,0.367 10 Engine Water Pump Assembly 4.287,1.316 4.614,1.5 0.326,0.184 10 E66 5.161,0.404 5.511,0.579 0.35,0.175 10 SWP 4.324,0.401 4.674,0.576 0.35,0.175 10 +B 5.161,1.003 5.505,1.157 0.344,0.154 10 NWP 5.565,0.915 5.698,1.095 0.133,0.179 10 2 4.173,0.915 4.306,1.095 0.133,0.179 10 4 4.173,0.308 4.306,0.488 0.133,0.179 10 3 5.565,0.322 5.698,0.501 0.133,0.179 10 1 4.324,0.988 4.833,1.193 0.509,0.205 10 PGND 5.855,0.915 6.08,1.077 0.225,0.162 10 28 5.855,0.322 6.08,0.484 0.225,0.162 10 29 6.103,0.999 6.438,1.164 0.335,0.165 10 WPI 6.103,0.404 6.48,0.569 0.377,0.165 10 WPO 6.116,3.661 6.684,3.928 0.568,0.267 10 MREL 5.866,3.563 6.102,3.729 0.237,0.166 10 46 6.415,4.25 6.779,4.429 0.365,0.179 10 ECM 1.811,1.066 2.648,1.306 0.837,0.24 10 ENG W/PMP 0.793,0.577 1.64,0.734 0.847,0.157 10 ENG W/PMP 1.861,0.764 2.008,0.952 0.147,0.189 10 1 2.413,0.764 2.555,0.914 0.141,0.151 10 2 2.413,0.308 2.537,0.488 0.124,0.179 10 5 1.861,0.308 1.961,0.478 0.101,0.17 10 3 1.852,2.399 2.529,2.708 0.677,0.309 10 EFI MAIN 0.533,4.351 0.901,4.55 0.367,0.2 10 MAIN 0.661,4.915 1.727,5.105 1.066,0.19 10 Auxiliary Battery 6.12,4.25 6.425,4.434 0.304,0.184 10 A25 1.411,3.017 2.503,3.41 1.093,0.392 10 No. 1 Integration Relay 1.23,2.815 1.464,2.996 0.233,0.18 10 1C 1.326,1.419 1.559,1.599 0.233,0.18 10 1C 1.361,2.625 1.503,2.796 0.142,0.17 10 7 2.502,2.813 2.742,2.983 0.24,0.17 10 1B 2.639,2.625 2.795,2.796 0.156,0.17 10 1 3.079,2.132 3.279,2.297 0.2,0.166 10 1E 3.134,1.952 3.262,2.108 0.128,0.156 10 2 1.621,1.419 1.778,1.575 0.156,0.156 10 3 1.319,1.82 1.997,2.017 0.677,0.197 10 EFI NO. 3 1.027,4.041 2.06,4.243 1.034,0.202 10 EFI-MAIN NO. 1 0.532,0.955 0.993,1.097 0.461,0.142 10 DC/DC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE ELECTRIC WATER PUMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Electric Water Pump.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the Electric Water Pump
50004 234 174

e.

Touch the engine water pump and check that the pump assembly is operating (vibrating).

OK:

The engine water pump assembly is operating (vibrating).



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
HINT:

Confirm a good connection at the engine water pump assembly and ECM connectors.


a.

Disconnect the engine water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E66-2 (NWP) - A25-28 (WPI) Always Below 1 Ω
E66-1 (SWP) - A25-29 (WPO) Always Below 1 Ω
E66-2 (NWP) or A25-28 (WPI) - Body ground Always 10 kΩ or higher
E66-1 (SWP) or A25-29 (WPO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (WPI VOLTAGE)
a.
A259201C03
0.427,1.823 0.917,2.115 0.49,0.292 1.969,1.917 2.49,1.646 false 0.521,1.875 0.792,2.052 0.271,0.177 10 false E66 2.552,1.542 2.969,1.75 0.417,0.208 10 false NWP 0.177,0.094 0.385,0.313 0.208,0.219 10 false *a
*a Front view of wire harness connector
(to Engine Water Pump Assembly)


Disconnect the engine water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E66-2 (NWP) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE WATER PUMP ASSEMBLY

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENGINE WATER PUMP ASSEMBLY)
HINT:

Confirm a good connection at the engine water pump assembly and ECM connectors.


a.
A259201C04
0.427,1.823 0.917,2.115 0.49,0.292 1.458,2.271 1.219,2.646 false 0.521,1.875 0.792,2.052 0.271,0.177 10 false E66 1.104,2.698 1.521,2.906 0.417,0.208 10 false +B 0.177,0.094 0.385,0.313 0.208,0.219 10 false *a
*a Front view of wire harness connector
(to Engine Water Pump Assembly)


Disconnect the engine water pump assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E66-3 (+B) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)

NG

9.INSPECT RELAY (ENG W/PMP RELAY)
5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the engine water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E66-4 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the engine water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E66-2 (NWP) - A25-28 (WPI) Always Below 1 Ω
E66-1 (SWP) - A25-29 (WPO) Always Below 1 Ω
E66-2 (NWP) or A25-28 (WPI) - Body ground Always 10 kΩ or higher
E66-1 (SWP) or A25-29 (WPO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ENGINE WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ENGINE WATER PUMP ASSEMBLY
a.

Replace the engine water pump assembly.

Click hereEngine / Hybrid System>2AR-FXE COOLING>WATER PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.


j.

Read the DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P261B, P261C or P261D is output A
DTC is not output B



A

B

END

9.INSPECT RELAY (ENG W/PMP RELAY)
a.
A268523E02
2.969,0.208 2.792,0.208 2.792,0.208 2.573,0.729 false 3.24,1.135 3.021,1.135 false 1.938,0.208 1.76,0.208 1.76,0.208 1.979,1.094 false 2.51,1.99 2.688,1.99 2.688,1.99 2.573,1.521 false 3,0.125 3.104,0.281 0.104,0.156 10 false 1 3.271,1.052 3.375,1.208 0.104,0.156 10 false 5 2.385,1.906 2.49,2.063 0.104,0.156 10 false 2 1.969,0.125 2.073,0.281 0.104,0.156 10 false 3

Remove the ENG W/PMP relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No auxiliary battery voltage applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - ENGINE WATER PUMP ASSEMBLY)

NG

REPLACE RELAY (ENG W/PMP RELAY)

10.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - ENGINE WATER PUMP ASSEMBLY)
a.

Remove the ENG W/PMP relay from the engine room relay block and junction block assembly.


b.

Disconnect the engine water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ENG W/PMP relay terminal 5 - E66-3 (+B) Always Below 1 Ω
ENG W/PMP relay terminal 5 or E66-3 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/PMP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ENG W/PMP RELAY)
a.
A266972C01
0.094,0.115 0.323,0.375 0.229,0.26 10 false *1 2.073,0.49 2.302,0.75 0.229,0.26 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ENG W/PMP Relay


Remove the ENG W/PMP relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ENG W/PMP relay terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - ENG W/P RELAY)

12.CHECK HARNESS AND CONNECTOR (ENG W/PMP RELAY - BODY GROUND)
a.

Remove the ENG W/PMP relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ENG W/PMP relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENG W/PMP RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR