Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › THROTTLE BODY
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074874 THROTTLE BODY A

2AR-FXE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22030 1.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

a.

Install a new gasket to the intake manifold.


b.

Install the throttle with motor body assembly and fuel tube bracket with 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the throttle body connector.


d.

Connect the 2 water by-pass hoses to the throttle with motor body assembly.


e.

Connect the 2 hoses.


Hide 2.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Install the air cleaner hose with the hose clamp.


b.
A262525C01
0.911,3.412 1.073,3.568 0.162,0.156 10 *1 1.892,3.858 2.055,4.014 0.162,0.156 10 *a 1.481,3.496 1.097,3.496 false
*1 Retainer
*a Push


Connect the 2 fuel vapor feed hoses.

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and pipe before performing this work.

·

Connect the quick connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer.

·

After connecting the fuel vapor feed hose to the fuel tube connector, check that the fuel vapor feed hose is securely connected by pulling on the fuel tube connector and the fuel vapor feed hose.




c.
A276664C01
0.906,0.885 0.552,0.885 0.552,0.885 0.552,1.906 true 0.844,1.479 0.552,1.479 true 2.417,0.927 2.063,0.927 2.063,0.927 2.063,1.917 true 2.448,1.656 2.063,1.656 true 0.448,1.906 0.625,2.073 0.177,0.167 10 true *a 1.979,1.917 2.156,2.083 0.177,0.167 10 true *b
*a Hinge
*b Clamp


Connect the 2 hinges of the air cleaner cap sub-assembly.


d.

Install the air cleaner cap sub-assembly with the 2 clamps.


e.

Connect the wire harness clamp and connector.


f.

Connect the ventilation hose to the cylinder head cover.


g.

Connect the mass air flow meter connector and wire harness clamp to the air cleaner cap sub-assembly.


Hide 4.INSPECT FOR COOLANT LEAK (for Engine)

Hide 12601B 5.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 6.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after reassembling the throttle with motor body assembly or removing and reinstalling any throttle body components.

·

Perform the following procedure after replacing the throttle with motor body assembly or any throttle body components. The following procedure should also be performed if the throttle body is cleaned.



a.

Turn the power switch on (IG) without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above step again.



b.

Connect the intelligent tester to the DLC3 and clear the DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR


c.

Perform the "Inspection After Repair".

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


d.

Set the vehicle to inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range when the A/C is switched off.

Standard:
Condition Engine Idle Speed
A/C switched off 900 to 1050 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P.




f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Sensor Position
50003 234 12

g.

Perform a road test and confirm that there are no abnormalities.