Refer to the description for DTC P0A2B-250 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250).
After confirming that DTC P0A2C-247 or P0A2D-249 is output, use the intelligent tester to check "Motor Temp No1" in the power management control ECU Data List.
| Displayed Temperature | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit or short to +B |
| 215°C (419°F) | Short circuit or short to GND |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A2C-247 | Drive Motor "A" Temperature Sensor Circuit Low | Short or short to GND in the motor temperature sensor circuit | ·
Wire harness or connector ·
Power management control ECU ·
Hybrid vehicle transaxle assembly (Motor temperature sensor) |
Does not come on | Master Warning Light:
Comes on |
| P0A2D-249 | Drive Motor "A" Temperature Sensor Circuit High | Open or short to +B in the motor temperature sensor circuit | ·
Wire harness or connector ·
Power management control ECU ·
Hybrid vehicle transaxle assembly (Motor temperature sensor) |
Does not come on | Master Warning Light:
Comes on |
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.
| Tester Display |
|---|
| Motor Temp No1 |
Read the Data List.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 215°C (419°F) | B |
| Same as actual temperature | C |
Turn the power switch off.
A
B
C
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
Disconnect the motor temperature sensor connector.
| *a | Front view of wire harness connector
(to Motor Temperature Sensor) |
Connect terminals 1 (MMT) and 3 (MMTG) of vehicle side connector E15 of the motor temperature sensor.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.
| Tester Display |
|---|
| Motor Temp No1 |
Connect the intelligent tester to the DLC3.
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Motor Temp No1 | Terminals MMT and MMTG connected.
Power switch on (IG) |
215°C (419°F) |
The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.
Turn the power switch off.
Connect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Power Management Control ECU) |
Connect terminals 24 (MMT) and 25 (MMTG) of connector A38 of the power management control ECU.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Motor Temp No1 | Terminals MMT and MMTG connected.
Power switch on (IG) |
215°C (419°F) |
Turn the power switch off.
Connect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the motor temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.
| Tester Display |
|---|
| Motor Temp No1 |
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Motor Temp No1 | Power switch on (IG) | -40°C (-40°F) |
The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.
Turn the power switch off.
Connect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the motor temperature sensor connector.
Disconnect connector A38 from the power management control ECU.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Motor Temperature Sensor) |
*b | Rear view of wire harness connector
(to Power Management Control ECU) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E15-1 (MMT) - A38-24 (MMT) | Power switch off | Below 1 Ω |
| E15-3 (MMTG) - A38-25 (MMTG) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E15-1 (MMT) or A38-24 (MMT) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| E15-3 (MMTG) or A38-25 (MMTG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the power management control ECU connector.
Connect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG