Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A38-257  Generator Temperature Sensor Circuit Low  P0A39-259  Generator Temperature Sensor Circuit High  


DESCRIPTION

Refer to the description for DTC P0A37-260 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A37-260).

HINT:

After confirming that DTC P0A38-257 or P0A39-259 is output, use the intelligent tester to check "Motor Temp No2" in the power management control ECU Data List.


Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A38-257 Generator Temperature Sensor Circuit Low Short to GND in the generator temperature sensor circuit
·

Wire harness or connector

·

Power management control ECU

·

Hybrid vehicle transaxle assembly (Generator temperature sensor)


Does not come on Master Warning Light:
Comes on
P0A39-259 Generator Temperature Sensor Circuit High Open or short to +B in the generator temperature sensor circuit
·

Wire harness or connector

·

Power management control ECU

·

Hybrid vehicle transaxle assembly (Generator temperature sensor)


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A159825E30
5.052,2.646 5.396,2.833 0.344,0.188 10 false A38 0.427,2.531 0.771,2.719 0.344,0.188 10 false E13 1.781,1.896 2.219,2.083 0.438,0.188 10 false GMTG 1.885,1.177 2.219,1.365 0.333,0.188 10 false GMT 5.146,1.167 5.49,1.354 0.344,0.188 10 false GMT 5.146,1.917 5.635,2.104 0.49,0.188 10 false GMTG 2.292,1.885 2.5,2.073 0.208,0.188 10 false 8 2.281,1.167 2.458,1.354 0.177,0.188 10 false 4 4.885,1.167 5.229,1.354 0.344,0.188 10 false 26 4.885,1.927 5.229,2.115 0.344,0.188 10 false 27 5.052,2.823 6.438,3.271 1.385,0.448 10 false Power Management Control ECU 0.417,2.698 2.646,3.146 2.229,0.448 10 false Hybrid Vehicle Transaxle Assembly (Generator Temperature Sensor)

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.READ VALUE USING INTELLIGENT TESTER (MOTOR TEMP NO2)

NG

CONNECT SECURELY

2.READ VALUE USING INTELLIGENT TESTER (MOTOR TEMP NO2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temp No2
50003 236 566

d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)

C

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)
a.
A259190

Disconnect the generator temperature sensor connector.


b.
A259192C02
0.24,1.01 0.656,1.25 0.417,0.24 2.021,1.271 2.563,1.688 false 2.01,1.021 2.552,0.594 false 0.135,0.052 0.323,0.271 0.188,0.219 10 false *a 0.333,1.052 0.677,1.25 0.344,0.198 10 false E13 2.594,0.49 2.938,0.635 0.344,0.146 10 false GMT 2.604,1.656 3.021,1.833 0.417,0.177 10 false GMTG
*a Front view of wire harness connector
(to Generator Temperature Sensor)


Connect terminals 4 (GMT) and 8 (GMTG) of vehicle side connector E13 of the generator temperature sensor.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temp No2
50003 236 566

f.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No2NG Terminals GMT and GMTG connected.
Power switch on (IG)
215°C (419°F)


HINT:

The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



g.

Turn the power switch off.


h.

Connect the generator temperature sensor connector.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - GENERATOR TEMPERATURE SENSOR)
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)
a.
A259190

Disconnect the generator temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.


e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No2 Power switch on (IG) -40°C (-40°F)


HINT:

The generator temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



f.

Turn the power switch off.


g.

Connect the generator temperature sensor connector.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - POWER MANAGEMENT CONTROL ECU)
5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - GENERATOR TEMPERATURE SENSOR)
a.
A249277C27
0.438,2.885 0.854,3.125 0.417,0.24 0.594,1.844 0.333,2.354 false 0.635,1.844 0.906,2.333 false 0.521,2.927 1.073,3.208 0.552,0.281 10 false A38 0.156,0.104 0.5,0.479 0.344,0.375 10 false *a 0.135,2.375 0.854,2.667 0.719,0.292 10 false GMTG 0.833,2.375 1.333,2.542 0.5,0.167 10 false GMT
*a Component with harness connected
(Power Management Control ECU)


Connect terminals 26 (GMT) and 27 (GMTG) of connector A38 of the power management control ECU.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No2.


e.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Motor Temp No2NG Terminals GMT and GMTG connected.
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (GENERATOR TEMPERATURE SENSOR - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the generator temperature sensor connector.


b.

Disconnect connector A38 from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

A306032C03
1.573,0.542 1.99,0.781 0.417,0.24 4.979,1.927 5.396,2.167 0.417,0.24 2.031,1.323 2.448,0.906 false 2.021,1.49 2.5,1.969 false 4.281,1.854 3.906,2.323 false 4.448,2.344 4.323,1.854 false 0.813,0.229 1.125,0.427 0.313,0.198 10 false *a 3.625,0.219 3.938,0.417 0.313,0.198 10 false *b 1.667,0.573 1.979,0.771 0.313,0.198 10 false E13 2.521,0.813 3.104,1.094 0.583,0.281 10 false GMT 2.552,1.906 3.135,2.188 0.583,0.281 10 false GMTG 3.656,2.344 4.24,2.625 0.583,0.281 10 false GMTG 4.313,2.354 4.896,2.635 0.583,0.281 10 false GMT 5.063,1.969 5.375,2.167 0.313,0.198 10 false A38
*a Front view or wire harness connector
(to Generator Temperature Sensor)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E13-4 (GMT) - A38-26 (GMT) Power switch off Below 1 Ω
E13-8 (GMTG) - A38-27 (GMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E13-4 (GMT) or A38-26 (GMT) - Body ground and other terminals Power switch off 10 kΩ or higher
E13-8 (GMTG) or A38-27 (GMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the power management control ECU connector.


e.

Connect the generator temperature sensor connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR