A resolver is a sensor that is used to detect the position of the magnetic poles the rotor of a motor generator. Knowing the position of the poles is indispensable for ensuring precise control of MG2 and MG1.
Each resolver contains a stator that has an excitation coil and 2 detection coils (S, C). The gap between the stator and rotor changes as the rotor turns because the rotor is oval shaped. An alternating current with a predetermined frequency flows through the excitation coil, and detection coils S and C output alternating currents in accordance with the sensor rotor position.
The MG ECU located in the inverter with converter assembly detects the absolute position of the rotor according to the phases of detection coils S and C and the heights of their waveforms. Furthermore, the CPU calculates the amount of change in the position within a predetermined length of time, in order to use the resolver as a speed sensor.
The MG ECU monitors signals output from the motor resolver and detects malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A4B-253 | Generator Position Sensor Circuit | Interphase short in the generator resolver circuit | ·
Inverter with converter assembly ·
Hybrid vehicle transaxle assembly ·
Wire harness or connector |
Comes on | Master Warning Light:
Comes on |
| P0A4C-513 | Generator Position Sensor Circuit Range / Performance | Generator resolver output is out of the normal range | ·
Inverter with converter assembly ·
Hybrid vehicle transaxle assembly ·
Wire harness or connector |
Comes on | Master Warning Light:
Comes on |
| P0A4D-255 | Generator Position Sensor Circuit Low | Open or short in the generator resolver circuit | ·
Inverter with converter assembly ·
Hybrid vehicle transaxle assembly ·
Wire harness or connector |
Comes on | Master Warning Light:
Comes on |
Refer to the wiring diagram for DTC P0A1A-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200).
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Check for output DTCs again after the repair has been completed. If P0A78-286 or P0A7A-324 is output, replace the inverter with converter assembly.
If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0343-747)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200)
| Proceed to |
|---|
| OK |
| NG |
OK
NG