Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0516-769  Battery Temperature Sensor Circuit Low  P0517-770  Battery Temperature Sensor Circuit High  


DESCRIPTION

The thermistor assembly detects the auxiliary battery temperature. The resistance of the thermistor assembly built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the thermistor assembly resistance. Conversely, the higher the temperature, the lower the resistance. The thermistor assembly is connected to the power management control ECU. A voltage of 5 V is supplied to the thermistor assembly from the THB terminal of the power management control ECU through its internal resistor R. This means that resistor R and the thermistor assembly are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the power management control ECU reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.

HINT:

Characteristics of the thermistor assembly resistance (reference values) are as follows.

Terminal THB
(with Connector Disconnected)
Resistance Ambient Temperature
THB - E2 4.5 to 5.5 V 3.00 to 3.73 kΩ Approximately 10°C (50°F)
1.60 to 1.80 kΩ Approximately 25°C (77°F)
0.80 to 1.00 kΩ Approximately 40°C (104°F)


A266952E01
0.881,1.216 1.916,1.367 1.035,0.151 10 Resistance (kΩ) 5.168,2.344 6.571,2.495 1.403,0.151 10 Temperature (°C (°F)) 2.392,2.239 2.578,2.39 0.186,0.151 10 10 2.336,2.404 2.617,2.555 0.281,0.151 10 (50) 2.794,2.404 3.075,2.555 0.281,0.151 10 (68) 3.252,2.404 3.534,2.555 0.281,0.151 10 (86) 3.67,2.404 4.032,2.555 0.361,0.151 10 (104) 4.125,2.404 4.494,2.555 0.369,0.151 10 (122) 4.573,2.404 4.963,2.555 0.39,0.151 10 (140 ) 2.845,2.239 3.043,2.39 0.198,0.151 10 20 3.304,2.239 3.502,2.39 0.198,0.151 10 30 3.767,2.239 3.958,2.39 0.191,0.151 10 40 4.217,2.239 4.426,2.39 0.209,0.151 10 50 4.678,2.239 4.884,2.39 0.206,0.151 10 60 2.15,2.11 2.397,2.262 0.247,0.151 10 0.0 2.15,1.886 2.397,2.037 0.247,0.151 10 0.5 2.15,1.661 2.397,1.812 0.247,0.151 10 1.0 2.15,1.436 2.397,1.587 0.247,0.151 10 1.5 2.15,1.211 2.397,1.363 0.247,0.151 10 2.0 2.15,0.987 2.397,1.138 0.247,0.151 10 2.5 2.15,0.762 2.397,0.913 0.247,0.151 10 3.0 2.15,0.537 2.397,0.688 0.247,0.151 10 3.5 2.15,0.312 2.397,0.464 0.247,0.151 10 4.0


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0516-769 Battery Temperature Sensor Circuit Low Malfunction in the thermistor assembly circuit (short to GND)
·

Thermistor assembly

·

Wire harness or connector

·

Power management control ECU


Does not come on Master Warning Light:
Does not come on
P0517-770 Battery Temperature Sensor Circuit High Malfunction in the thermistor assembly circuit (open or short to +B)
·

Thermistor assembly

·

Wire harness or connector

·

Power management control ECU


Does not come on Master Warning Light:
Does not come on

WIRING DIAGRAM

A259938E18
4.479,3.125 6.615,3.49 2.135,0.365 10 false Power Management Control ECU 4.479,2.948 4.76,3.104 0.281,0.156 10 false I3 1.26,3.167 2.802,3.531 1.542,0.365 10 false Thermistor Assembly 1.271,3 1.802,3.156 0.531,0.156 10 false O26 2.146,1.104 2.458,1.302 0.313,0.198 10 false THB 2.542,1.115 2.677,1.313 0.135,0.198 10 false 2 2.542,2.115 2.677,2.313 0.135,0.198 10 false 1 4.583,1.104 4.792,1.302 0.208,0.198 10 false 28 4.583,2.115 4.792,2.313 0.208,0.198 10 false 30 2.25,2.115 2.458,2.313 0.208,0.198 10 false E2 4.802,1.104 5.115,1.302 0.313,0.198 10 false THB 4.833,2.115 5.271,2.313 0.438,0.198 10 false ETHB

CAUTION / NOTICE / HINT

HINT:
·

Read the freeze frame data using the intelligent tester. In the freeze frame data, some information is recorded about the vehicle conditions at the moment a malfunction occurred. This information can be helpful when troubleshooting.

·

After confirming that DTC P0516-769 or P0517-770 is output, use the intelligent tester to check "Auxiliary Batt Temperature" in the Hybrid Control Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE)

NG

CONNECT SECURELY

2.READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Auxiliary Batt Temperature
50003 236 504

d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)

C

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)
a.
A259380E02
0.344,1.042 0.76,1.281 0.417,0.24 0.427,1.083 0.75,1.25 0.323,0.167 10 false O26

Disconnect connector O26 from the thermistor assembly.


b.
A237420C14
0.458,0.896 0.875,1.135 0.417,0.24 1.573,1.26 1.208,1.625 true 1.833,1.271 2.25,1.646 true 0.531,0.938 0.813,1.104 0.281,0.167 10 false O26 0.146,0.094 0.344,0.271 0.198,0.177 10 false *a 2.167,1.667 2.49,1.844 0.323,0.177 10 false THB 1.073,1.656 1.292,1.833 0.219,0.177 10 false E2
*a Front view of wire harness connector
(to Thermistor Assembly)


Connect terminals 2 (THB) and 1 (E2) of vehicle side connector O26 of the thermistor assembly.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Auxiliary Batt Temperature
50003 236 504

f.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Terminals THB and E2 connected.
Power switch on (IG)
215°C (419°F)



g.

Turn the power switch off.


h.

Connect the thermistor assembly connector.

Result:
Proceed to
OK
NG




OK

REPLACE THERMISTOR ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)
a.
A259380E02
0.344,1.042 0.76,1.281 0.417,0.24 0.427,1.083 0.75,1.25 0.323,0.167 10 false O26

Disconnect connector O26 from the thermistor assembly.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Auxiliary Batt Temperature
50003 236 504

e.

Read the Data List.

OK:
Tester Display Switch Condition Specified Condition
Auxiliary Batt Temperature Power switch on (IG) -40°C (-40°F)



f.

Turn the power switch off.


g.

Connect the thermistor assembly connector.

Result:
Proceed to
OK
NG




OK

REPLACE THERMISTOR ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY)
a.
A249750C09
1.906,2.563 2.323,2.802 0.417,0.24 2.188,1.906 1.958,2.281 true 2.281,1.917 2.542,2.281 true 2.063,2.604 2.344,2.771 0.281,0.167 10 false I3 0.177,0.156 0.448,0.323 0.271,0.167 10 false *a 2.406,2.281 2.719,2.448 0.313,0.167 10 false THB 1.729,2.281 2.125,2.448 0.396,0.167 10 false ETHB
*a Component with harness connected
(Power Management Control ECU)


Connect terminals 28 (THB) and 30 (ETHB) of connector I3 of the power management control ECU.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.

Powertrain > Hybrid Control > Data List
Tester Display
Auxiliary Batt Temperature
50003 236 504

e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Terminals THB and ETHB connected.
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect connector O26 from the thermistor assembly.


b.

Disconnect connector I3 from the power management control ECU.


c.
A285931C05
2.365,0.813 2.781,1.135 0.417,0.323 1.198,3.375 1.635,3.667 0.438,0.292 1.479,1.083 1,1.51 true 1.802,1.063 2.24,1.521 true 2.208,3.781 1.646,4.042 true 2.302,3.771 2.563,4 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 2.448,0.896 2.906,1.094 0.458,0.198 10 false O26 0.813,1.5 1.125,1.698 0.313,0.198 10 false E2 2.281,1.5 2.74,1.698 0.458,0.198 10 false THB 0.135,1.823 0.448,2.021 0.313,0.198 10 false *b 1.375,3.448 1.688,3.646 0.313,0.198 10 false I3 1.26,3.969 1.875,4.167 0.615,0.198 10 false ETHB 2.604,3.927 3.063,4.125 0.458,0.198 10 false THB
*a Front view of wire harness connector
(to Thermistor Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
O26-2 (THB) - I3-28 (THB) Power switch off Below 1 Ω
O26-1 (E2) - I3-30 (ETHB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
O26-2 (THB) or I3-28 (THB)- Body ground and other terminals Power switch off 10 kΩ or higher
O26-1 (E2) or I3-30 (ETHB)- Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the thermistor assembly connector.


e.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR