Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2120-152  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2121-106  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  P2122-104  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123-105  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125-153  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2126-109  Throttle / Pedal Position Sensor / Switch "E" Circuit Range / Performance  P2127-107  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128-108  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138-110  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  P2138-154  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal to detect how much the pedal is depressed. This is a non-contact sensor with hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA1 and VPA2 of the power management control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The power management control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA1 and VPA2.

A222964E13
0.76,2.708 0.76,3.427 0.76,3.427 0.854,3.427 false 0.76,1.615 0.76,0.75 0.76,0.75 0.865,0.75 false 0.74,2.01 0.219,0.385 0.219,0.385 0.302,0.385 false 0.75,2.354 0.198,3.813 0.198,3.813 0.281,3.813 false 0.875,0.698 1.5,0.969 0.625,0.271 10 false Magnet 0.333,0.313 1.219,0.573 0.885,0.26 10 false Hall Element 0.333,3.74 1.281,3.969 0.948,0.229 10 false Hall Element 0.875,3.354 1.406,3.667 0.531,0.313 10 false Magnet 1.74,3.635 3.073,4.115 1.333,0.479 10 false Power Management Control ECU 2.865,1.771 4.073,2.542 1.208,0.771 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.5,0.708 6.865,0.99 2.365,0.281 10 false Accelerator Pedal Opening Angle (°) 4.396,4.094 6.927,4.313 2.531,0.219 10 false *1: Accelerator Pedal Fully Released 4.396,4.385 6.938,4.667 2.542,0.281 10 false *2: Accelerator Pedal Fully Depressed 0.198,4.063 1.427,4.521 1.229,0.458 10 false Accelerator Pedal Sensor Assembly 2.219,1.104 2.542,1.344 0.323,0.24 10 false 5 V 4.229,1.01 4.323,1.177 0.094,0.167 10 false 5 4.229,2.396 4.479,2.583 0.25,0.188 10 false 0 3.938,1.271 4.323,1.438 0.385,0.167 10 false 3.988 3.938,1.469 4.323,1.635 0.385,0.167 10 false 3.188 4.104,1.938 4.385,2.125 0.281,0.188 10 false 1.6 6.854,1.115 7.146,1.281 0.292,0.167 10 false 4.55 6.854,1.333 7.146,1.5 0.292,0.167 10 false 3.75 6.656,2.49 6.833,2.656 0.177,0.167 10 false 20 4.25,2.823 4.531,3.042 0.281,0.219 10 false *1 6.052,2.823 6.302,3.063 0.25,0.24 10 false *2 5.104,2.49 5.552,2.698 0.448,0.208 10 false 13.1 4.104,2.156 4.448,2.344 0.344,0.188 10 false 0.8 2.51,1.938 2.802,2.229 0.292,0.292 10 false 5 V 2.198,1.677 2.521,1.938 0.323,0.26 10 false AD 2.365,2.552 2.719,2.823 0.354,0.271 10 false AD

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P2120-152 Throttle / Pedal Position Sensor / Switch "D" Circuit Main sensor circuit wiring malfunction or level is not stable
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2121-106 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance Internal error of the main sensor
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2122-104 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input Open or short to GND in the main sensor circuit
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2123-105 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input Short to +B in the main sensor circuit
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2125-153 Throttle / Pedal Position Sensor / Switch "E" Circuit Sub sensor circuit wiring malfunction or level is not stable
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2126-109 Throttle / Pedal Position Sensor / Switch "E" Circuit Range / Performance Internal error of the sub sensor
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2127-107 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input Open or short to GND in the sub sensor circuit
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2128-108 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Short to +B in the sub sensor circuit
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2138-110 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Difference between the main sensor value and sub sensor value is large.
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P2138-154 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Main or sub sensor circuit wiring malfunction
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A169668E30
1.792,0.531 2.208,0.792 0.417,0.26 10 false VCP1 1.792,1.844 2.198,2.052 0.406,0.208 10 false VCP2 1.802,0.958 2.229,1.219 0.427,0.26 10 false VPA1 1.813,2.271 2.219,2.542 0.406,0.271 10 false VPA2 1.885,1.396 2.24,1.625 0.354,0.229 10 false EP1 0.594,3.031 0.906,3.24 0.313,0.208 10 false A36 1.875,2.719 2.208,2.948 0.333,0.229 10 false EP2 5.323,0.427 5.813,0.656 0.49,0.229 10 false VCP1 5.094,0.417 5.344,0.615 0.25,0.198 10 false 18 5.094,0.875 5.313,1.115 0.219,0.24 10 false 26 5.083,1.313 5.365,1.573 0.281,0.26 10 false 34 5.094,1.76 5.344,1.979 0.25,0.219 10 false 19 5.094,2.188 5.354,2.406 0.26,0.219 10 false 27 5.094,2.635 5.354,2.896 0.26,0.26 10 false 35 5.323,1.76 5.792,1.979 0.469,0.219 10 false VCP2 5.323,0.875 5.76,1.125 0.438,0.25 10 false VPA1 5.323,2.188 5.813,2.448 0.49,0.26 10 false VPA2 5.323,1.313 5.698,1.583 0.375,0.271 10 false EP1 5.323,2.635 5.708,2.865 0.385,0.229 10 false EP2 0.583,3.24 2.875,3.531 2.292,0.292 10 false Accelerator Pedal Sensor Assembly 4.969,3.135 5.396,3.344 0.427,0.208 10 false A39 4.969,3.323 7.083,3.646 2.115,0.323 10 false Power Management Control ECU 2.26,0.417 2.375,0.563 0.115,0.146 10 false 4 2.26,0.854 2.375,1 0.115,0.146 10 false 6 2.26,1.302 2.375,1.448 0.115,0.146 10 false 5 2.26,1.75 2.375,1.896 0.115,0.146 10 false 1 2.26,2.198 2.375,2.344 0.115,0.146 10 false 3 2.26,2.635 2.375,2.781 0.115,0.146 10 false 2 6.104,1.719 6.5,1.979 0.396,0.26 10 false 5 V 6.094,0.448 6.427,0.719 0.333,0.271 10 false 5 V 5.792,1.125 6.281,1.781 0.49,0.656 10 false 39 kΩ+/-5 % 5.833,2.49 6.281,3.083 0.448,0.594 10 false 39 kΩ+/-5 %

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1, Accel Pedal Pos #2.

Powertrain > Hybrid Control > Data List
Tester Display
Accel Pedal Pos #1
Accel Pedal Pos #2
50003 236 15,16

d.

Read the Data List.

Result:
Tester Display Accelerator Pedal Condition Specified Condition
Accel Pedal Pos #1 Not depressed 8 to 28%
Fully depressed 62 to 92%
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively
Accel Pedal Pos #2 Not depressed 20 to 44%
Fully depressed 78 to 100%
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively



e.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
a.
A260211

Check the connection of the accelerator pedal sensor assembly connector.

OK:

The connector is connected securely and there are no contact problems.


Result:
Proceed to
OK
NG




OK

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)

NG

CONNECT SECURELY

4.CHECK POWER MANAGEMENT CONTROL ECU (CHECK VOLTAGE)
a.

Disconnect connector A36 from the accelerator pedal sensor assembly.


b.

Turn the power switch on (IG).


c.
A218062C30
2.781,0.979 3.271,1.271 0.49,0.292 1.292,1.167 0.906,1.813 true 1.5,1.167 1.438,1.802 true 1.802,1.177 1.99,1.781 true 1.99,1.135 2.573,1.792 true 0.729,1.823 1.167,1.979 0.438,0.156 10 false VCP2 1.302,1.823 1.74,1.979 0.438,0.156 10 false EP2 1.844,1.823 2.281,1.979 0.438,0.156 10 false VCP1 2.448,1.823 2.75,1.979 0.302,0.156 10 false EP1 2.875,1.031 3.25,1.198 0.375,0.167 10 false A36 0.083,0.083 0.531,0.323 0.448,0.24 10 false *a
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-4 (VCP1) - A36-5 (EP1) Power switch on (IG) 4.5 to 5.5 V
A36-1 (VCP2) - A36-2 (EP2) Power switch on (IG) 4.5 to 5.5 V



d.

Turn the power switch off.


e.

Connect the accelerator pedal sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
5.CHECK POWER MANAGEMENT CONTROL ECU (CHECK RESISTANCE)
a.

Disconnect connector A36 from the accelerator pedal sensor assembly.


b.
A218062C31
2.781,0.979 3.271,1.271 0.49,0.292 1.448,1.156 0.917,1.833 true 1.948,1.177 2.063,1.833 true 1.646,1.156 1.51,1.823 true 2.135,1.177 2.552,1.844 true 1.323,1.854 1.76,2.01 0.438,0.156 10 false VPA2 0.781,1.854 1.219,2.01 0.438,0.156 10 false EP2 2.375,1.854 2.813,2.01 0.438,0.156 10 false VPA1 1.927,1.854 2.229,2.01 0.302,0.156 10 false EP1 2.875,1.042 3.302,1.229 0.427,0.188 10 false A36 0.073,0.083 0.698,0.375 0.625,0.292 10 false *a
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A36-6 (VPA1) - A36-5 (EP1) Power switch off 36.60 to 41.61 kΩ
A36-3 (VPA2) - A36-2 (EP2) Power switch off 36.60 to 41.61 kΩ



c.

Connect the accelerator pedal sensor assembly connector.

Result:
Proceed to
OK
NG




OK

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect connector A36 from the accelerator pedal sensor assembly.


b.

Disconnect connector A39 from the power management control ECU.


c.

Turn the power switch on (IG).


d.
A284566C16
2.823,3.521 3.229,3.865 0.406,0.344 2.625,1.802 3.042,2.115 0.417,0.313 0.844,1.833 1.156,1.979 true 1.208,1.99 2.073,1.813 true 0.823,2.167 1.156,2.125 true 1.188,2.125 2.042,2.188 true 0.75,4.313 1.333,3.75 true 1.406,4.302 1.531,3.781 true 1.865,3.76 2.177,4.302 true 2.031,3.771 2.802,4.26 true 0.042,0.094 0.354,0.25 0.313,0.156 10 false *a 0.094,2.906 0.406,3.063 0.313,0.156 10 false *b 0.438,1.75 0.844,1.906 0.406,0.156 10 false VCP2 0.573,4.344 0.948,4.521 0.375,0.177 10 false VCP2 2.115,1.719 2.521,1.896 0.406,0.177 10 false VCP1 2.021,4.323 2.396,4.5 0.375,0.177 10 false VCP1 0.51,2.083 0.823,2.26 0.313,0.177 10 false EP2 1.281,4.333 1.656,4.521 0.375,0.188 10 false EP2 2.115,2.104 2.417,2.26 0.302,0.156 10 false EP1 2.688,4.313 2.979,4.49 0.292,0.177 10 false EP1 2.698,1.875 3.125,2.146 0.427,0.271 10 false A39 2.927,3.625 3.271,3.885 0.344,0.26 10 false A36
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-18 (VCP1) - Body ground Power switch on (IG) Below 1 V
A39-34 (EP1) - Body ground Power switch on (IG) Below 1 V
A39-19 (VCP2) - Body ground Power switch on (IG) Below 1 V
A39-35 (EP2) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-18 (VCP1) - A36-4 (VCP1) Power switch off Below 1 Ω
A39-34 (EP1) - A36-5 (EP1) Power switch off Below 1 Ω
A39-19 (VCP2) - A36-1 (VCP2) Power switch off Below 1 Ω
A39-35 (EP2) - A36-2 (EP2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-18 (VCP1) or A36-4 (VCP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-34 (EP1) or A36-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-19 (VCP2) or A36-1 (VCP2) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-35 (EP2) or A36-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the power management control ECU connector.


h.

Connect the accelerator pedal sensor assembly connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect connector A36 from the accelerator pedal sensor assembly.


b.

Disconnect connector A39 from the power management control ECU.


c.

Turn the power switch on (IG).


d.
A284566C17
2.844,3.521 3.344,3.823 0.5,0.302 2.51,1.833 2.979,2.125 0.469,0.292 1.156,2.052 0.802,1.927 true 0.896,2.313 1.156,2.115 true 1.188,2.052 2,1.927 true 1.198,2.115 1.99,2.354 true 0.823,4.25 1.5,3.76 true 1.427,4.26 1.646,3.771 true 2.031,3.771 2.073,4.281 true 2.177,3.76 2.719,4.271 true 0.052,0.052 0.438,0.25 0.385,0.198 10 false *a 0.094,2.625 0.448,2.948 0.354,0.323 10 false *b 0.365,1.844 0.74,2.01 0.375,0.167 10 false VPA2 2.083,1.833 2.479,1.979 0.396,0.146 10 false VPA1 0.573,2.24 0.885,2.396 0.313,0.156 10 false EP2 2.063,2.271 2.365,2.438 0.302,0.167 10 false EP1 0.677,4.292 1,4.448 0.323,0.156 10 false EP2 1.229,4.302 1.625,4.458 0.396,0.156 10 false VPA2 1.927,4.313 2.219,4.469 0.292,0.156 10 false EP1 2.531,4.302 2.917,4.469 0.385,0.167 10 false VPA1 2.969,3.594 3.323,3.823 0.354,0.229 10 false A36 2.604,1.885 2.938,2.188 0.333,0.302 10 false A39
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-26 (VPA1) - Body ground Power switch on (IG) Below 1 V
A39-27 (VPA2) - Body ground Power switch on (IG) Below 1 V
A39-34 (EP1) - Body ground Power switch on (IG) Below 1 V
A39-35 (EP2) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-26 (VPA1) - A36-6 (VPA1) Power switch off Below 1 Ω
A39-34 (EP1) - A36-5 (EP1) Power switch off Below 1 Ω
A39-27 (VPA2) - A36-3 (VPA2) Power switch off Below 1 Ω
A39-35 (EP2) - A36-2 (EP2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-26 (VPA1) or A36-6 (VPA1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-34 (EP1) or A36-5 (EP1) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-27 (VPA2) or A36-3 (VPA2) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-35 (EP2) or A36-2 (EP2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the power management control ECU connector.


h.

Connect the accelerator pedal sensor assembly connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR