Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV mode signal is sent to the power management control ECU. This signal is then transmitted from the power management control ECU via CAN to the combination meter assembly to illuminate the EV mode indicator light.

WIRING DIAGRAM

A259907E02
4.442,2.911 6.585,3.109 2.142,0.198 10 Power Management Control ECU 4.442,2.757 4.826,2.955 0.383,0.198 10 I3 5.185,2.169 5.758,2.409 0.573,0.24 10 EVSW 4.849,2.083 5.158,2.336 0.309,0.253 10 13 1.528,1.244 3.409,1.399 1.881,0.155 10 Combination Meter Assembly 1.318,2.575 1.711,2.759 0.392,0.184 10 I48 1.304,2.729 3.666,3.072 2.362,0.342 10 EV Drive Mode Switch (Pattern Select Switch Assembly) 0.66,3.402 2.191,3.544 1.531,0.142 10 : CAN Communication 1.851,2.057 2.215,2.289 0.365,0.232 10 E 3.041,2.057 3.392,2.301 0.351,0.244 10 S 3.252,2.057 3.588,2.251 0.337,0.194 10 4 1.61,2.057 1.727,2.251 0.117,0.194 10 1

INSPECTION PROCEDURE

If any of the following conditions are not met, EV mode may not be turned on or the mode may be cancelled. (A buzzer sounds to indicate that the transition to EV mode is cancelled.)

EV Mode Entry Condition Tester Display Specified Condition
HV battery charge level State of Charge (All Bat) Approximately 50% or higher
Accelerator pedal position Accelerator Degree Below approximately 30%
Engine coolant temperature Engine Coolant Temp 20°C (68°F) or higher
HV battery temperature Temp of Batt TB1 to TB3 Between 10 to 40°C (50 to 104°F)
Vehicle speed
(Varies depending on engine warm-up condition)
Vehicle Spd Cold: 30 km/h (19 mph) or less
Warmed-up: 40 km/h (25 mph)
Win Charge Control Value Below -5000 kW
Wout Discharge Control Value 11500 kW or higher
Defroster - OFF
Cruise control - OFF

PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV mode.

Result:
Result Proceed to
No buzzer sounded and no message was displayed on multi-information display. A
A buzzer sounded and a message was displayed on multi-information display. B



HINT:

If a buzzer sounds and a message is displayed on multi-information display, one or more of the EV mode entry conditions have not been met. Check that all of the EV mode entry conditions have been met before pressing the EV drive mode switch (pattern select switch assembly).



A

2.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)

B

COMPLETED

2.READ VALUE USING INTELLIGENT TESTER (CAN BUS CHECK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / CAN Bus Check.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B



d.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (ALL CODES)

B

3.CHECK DTC OUTPUT (ALL CODES)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: System Select / Utility / All Codes.


d.

Check DTCs.

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



e.

Turn the power switch off.



A

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. EV MODE)

B

GO TO DTC CHART

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. EV MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Body / Combination Meter / Active Test / Indicat. EV Mode.


d.

Perform the "Indicat. EV Mode" Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. EV Mode
50004 122 68
OK:

The EV mode indicator light comes on or blinks.



e.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

5.READ VALUE USING INTELLIGENT TESTER (EV REQUEST, EV SWITCH)

NG

REPLACE COMBINATION METER ASSEMBLY

5.READ VALUE USING INTELLIGENT TESTER (EV REQUEST, EV SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / EV request, EV Switch.


d.

Read the value displayed on the intelligent tester.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EV Request EV mode transition availability ON or OFF In EV mode: ON -
EV Switch EV drive mode switch (pattern select switch assembly) condition ON or OFF EV drive mode switch (pattern select switch assembly) being pushed and held: ON -
Powertrain > Hybrid Control > Data List
Tester Display
EV Request
EV Switch
50003 236 544,88

Result:
Result Proceed to
The intelligent tester display changes according to the EV drive mode switch (pattern select switch assembly) operation. A
The intelligent tester display does not change according to the EV drive mode switch (pattern select switch assembly) operation. B


e.

Turn the power switch off.



A

B

6.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
6.INSPECT EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
a.

Remove the EV drive mode switch (pattern select switch assembly)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COMBINATION SWITCH>COMPONENTS


b.
A259195C07
0.254,0.187 0.438,0.352 0.184,0.166 10 *a 0.444,0.94 0.906,1.225 0.463,0.286 0.552,0.993 0.777,1.156 0.226,0.163 10 I48 1.038,1.703 1.151,1.867 0.112,0.163 10 S 1.124,1.681 1.422,1.234 false 2.293,1.703 2.405,1.867 0.112,0.163 10 E 2.333,1.681 2.035,1.234 false
*a Component without harness connected
(EV Drive Mode Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I48-4 (S) - I48-1 (E) EV drive mode switch (pattern select switch assembly) being pushed and held Below 1 Ω
EV drive mode switch (pattern select switch assembly) not pushed 10 kΩ or higher



c.

Install the EV drive mode switch (pattern select switch assembly).


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect connector I48 from the EV drive mode switch (pattern select switch assembly).


b.
A259196C04
0.57,0.98 1.032,1.265 0.463,0.286 0.678,1.033 0.901,1.196 0.223,0.163 10 I48 1.036,1.775 1.155,1.938 0.119,0.163 10 E 0.294,0.234 0.475,0.397 0.182,0.163 10 *a 1.122,1.752 1.419,1.306 false
*a Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I48-1 (E) - Body ground Always Below 1 Ω



c.

Connect the EV drive mode switch (pattern select switch assembly) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - EV DRIVE MODE SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
a.

Disconnect connector I3 from the power management control ECU.


b.

Disconnect connector I48 from the EV drive mode switch (pattern select switch assembly).


c.
A259932C03
0.542,3.406 1,3.688 0.458,0.281 1.208,1.552 1.667,1.833 0.458,0.281 2.375,4.146 2.052,3.698 true 1.792,2.292 1.969,1.75 true 0.677,3.427 0.927,3.656 0.25,0.229 10 false I48 1.396,1.583 1.625,1.802 0.229,0.219 10 false I3 2.365,4.167 2.583,4.427 0.219,0.26 10 false S 0.26,2.656 0.438,2.823 0.177,0.167 10 false *b 0.26,0.052 0.438,0.219 0.177,0.167 10 false *a 1.5,2.333 2.031,2.604 0.531,0.271 10 false EVSW
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to EV Drive Mode Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-13 (EVSW) - I48-4 (S) Always Below 1 Ω
I3-13 (EVSW) or I48-4 (S) - Body ground Always 10 kΩ or higher



d.

Connect the EV drive mode switch (pattern select switch assembly) connector.


e.

Connect the power management control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR