Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM Y

NETWORKING  CAN COMMUNICATION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

PRECAUTIONS WHEN TROUBLESHOOTING


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

·

If the CAN communication system is malfunctioning, check the contact pressure of the terminals in connectors, as insufficient terminal contact pressure may be the cause.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

·

Refer to Diagnosis System for the DTCs for the CAN communication system.

·

Refer to troubleshooting of each system if DTCs regarding the CAN communication system are not output.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



a.

CAN communication DTCs are output for CAN main bus and CAN branch malfunctions as well as for internal malfunctions or power source malfunctions of ECUs or sensors for systems using CAN communication. Therefore, when DTCs for internal malfunctions or power source malfunctions of corresponding systems are output at the same time as CAN communication DTCs, troubleshoot according to the internal malfunction and power source malfunction DTCs.


b.

The DLC3 branch and V bus main bus circuits can be checked for malfunctions by inspecting at the DLC3 terminals using a electrical tester.

NOTICE:
·

When inspecting at the DLC3 connector, do not connect the tester directly to the terminals. Instead, connect using service wires.

·

Inspections for an open in an ECU or sensor branch, or inspections for buses other than the V bus cannot be performed from the DLC3.




c.

An open in a branch for ECUs or sensors that are connected to the CAN main bus can be checked by performing a communication bus check using the intelligent tester. (This inspection is possible when the DLC3 branch and V bus main bus lines are normal.)


d.

If the V bus had a communication error, the probable ECU or sensor for which communication stopped can be determined using the combination of communication DTCs (DTCs that start with U) that are output.


e.

A malfunction of sub bus 15 can be determined based on the number of DTCs stored by the ECM, power management control ECU and brake booster with master cylinder assembly (skid control ECU).


f.

If a sub bus has a communication error, the gateway function equipped ECU (sub bus monitor ECU) detects it and stores DTCs related to the error.

HINT:

On the intelligent tester, gateway function equipped ECUs display DTCs for ECUs connected to the sub bus.



g.

When an open circuit is detected, before disconnecting related connectors for inspection, push in on the connector body to check that the connector is not loose or disconnected.


h.

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
HINT:
·

If the power switch can be turned on (IG) (the power source mode can be changed to on (IG)) when the vehicle is brought in for repair, check for DTCs and check the illumination condition of the indicators in the combination meter assembly and the basic operation of the vehicle (such as steering operation) promptly.

·

Do not turn the power switch off until the inspection of the vehicle is finished, as some fail-safe functions are canceled when the power switch is turned off.

·

If the power switch cannot be turned on (IG) (the power source mode cannot be changed to on (IG)) when the vehicle is brought in, measure the auxiliary voltage of the battery. If the voltage is below 11 V, recharge or replace the auxiliary battery before performing troubleshooting.

·

If the power switch cannot be turned on (IG) even though the auxiliary battery voltage is normal, repair this malfunction before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Ask the customer if the vehicle is/was equipped with additional devices such as a theft deterrent device or monitor. (If equipped, explain the customer that the additional devices will be removed before performing troubleshooting as the malfunction cannot be checked properly.)



a.

It is useful to confirm the symptoms and the conditions in which the vehicle was operating at the time when a malfunction occurred. This helps to narrow down the malfunctioning part.

HINT:
·

What was affected (system, part or meter warning indicators)

·

What happened (details of the malfunction)

·

When (occurrence date and time, frequency and if it recurs or not)

·

Under what kind of situation did the problem occur (driving and operating condition at the occurrence and weather)

·

Road type or condition (city, suburb, paved road, unpaved road, highway, etc.)

·

Return conditions (what made the vehicle return to normal. Example: power switch was turned off)



Points to be confirmed
Symptom
·

Electric power steering

- Normal

- A little heavier than usual

- There was no assist

·

Air conditioning

- Whether the air conditioning system operated

- Whether the blower fan operated

·

Multi-information display items

- Whether the update of multi-information display items stopped

- Whether the numeric part of drivable distance was not displayed

·

Door inside handle illumination

- Whether the door inside handle illumination was dimmed when the shift lever was in a position other than P

·

Auto lock and unlock operation

- Whether the speed linked auto-lock function operated while driving

- Whether the unlock function operated when the shift lever was moved to P

·

Wireless door lock function and smart entry function

- Whether the lock/unlock function operated

- Whether the illumination was turned on when the key was brought into a smart detection area

·

Operation of other systems of concern


Meter warning lights
·

Illumination of warning lights and the order in which they illuminated

- HV system warning light

- Check engine (MIL)

- ABS

- SRS

- EPS

- SLIP

- Master

- Brake

- Cruise (amber)

- Others

·

Needle movement

- Speedometer

- Coolant temperature gauge

- Hybrid system indicator

·

Content displayed on the multi-information display




Result:
Proceed to
NEXT



NEXT

3.CHECK INTELLIGENT TESTER OPERATION
3.CHECK INTELLIGENT TESTER OPERATION
HINT:

Read the intelligent tester operators manual before use.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Check that the intelligent tester and ECUs can communicate with the power switch on (IG).


HINT:
·

If communication is impossible, the intelligent tester screen will indicate an error.

·

If communication between the intelligent tester and ECUs is impossible, either the intelligent tester or vehicle has a malfunction.

·

When communication between the intelligent tester and the vehicle is impossible, but communication is possible when the intelligent tester is connected to another vehicle, the vehicle has the malfunction. Inspect the CANH and CANL branch lines of the DLC3 and the ECU power source circuits (in this case perform steps 7 to 9 first). In addition, check that the BAT terminal of the DLC3 receives auxiliary battery voltage (11 V or more).

·

If communication between the intelligent tester and ECUs is still impossible even when the intelligent tester is connected to another vehicle, the intelligent tester has the malfunction. Perform the self tests described in the intelligent tester operators manual. (The intelligent tester may be malfunctioning or its battery may be discharged.)



Result:
Result Proceed to
OK (Communication between the intelligent tester and the vehicle is possible.) A
OK (Communication between the intelligent tester and the vehicle is impossible but communication is possible when connected to another vehicle.) B
NG (Communication is not possible between the intelligent tester and the vehicle, nor between the intelligent tester and another vehicle.) C



A

4.CHECK DTC

B

7.CHECK DLC3 BRANCH LINE AND V BUS MAIN LINE (CANH - CANL)

C

Refer to intelligent tester operator's manual

4.CHECK DTC
a.

Using the intelligent tester, perform All Codes to read current and history DTCs and record them.

NOTICE:
·

CAN communication DTCs are output when there is an open or short in any of the communication lines. Any problems with the power source of a corresponding ECU or sensor, or problems in the ECU, the sensor itself also cause these DTCs to be output.

·

If a CAN communication line connector is disconnected with the power switch on (IG), the ECUs of the corresponding system and related systems store a DTC.



HINT:
·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in a CAN bus occurs, DTCs of almost all ECUs and sensors on the CAN bus may be output (or a message indicating a communication error may be displayed on the intelligent tester screen). In this case, check the resistance of the CAN bus (steps 7 to 9) first.

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed on the intelligent tester.




b.

Read the freeze frame data using the intelligent tester and record it.


Result:
Proceed to
NEXT



NEXT

5.CHECK COMMUNICATION MALFUNCTION DTCs (CONNECTION STATUS CHECK USING INTELLIGENT TESTER)
5.CHECK COMMUNICATION MALFUNCTION DTCs (CONNECTION STATUS CHECK USING INTELLIGENT TESTER)
a.

Select "Communication Malfunction DTC" from the screen on the intelligent tester.


b.

Record all the DTCs stored for ECUs and sensors.


Result:
Proceed to
NEXT



NEXT

6.CHECK COMMUNICATION BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER)
6.CHECK COMMUNICATION BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER)
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Select "Communication Bus Check" from the screen on the intelligent tester.


CAN Bus Check
50007
c.

Observe the screen for approximately 2 minutes to check the ECUs and sensors displayed on the screen.


Result:
Proceed to
NEXT



NEXT

7.CHECK DLC3 BRANCH LINE AND V BUS MAIN LINE (CANH - CANL)
7.CHECK DLC3 BRANCH LINE AND V BUS MAIN LINE (CANH - CANL)
NOTICE:

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C210421C02
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.208,1.313 2.208,1.313 2.427,1.313 false 2.073,2.573 2.198,2.948 2.198,2.948 2.354,2.948 false 0.115,0.156 0.958,0.49 0.844,0.333 10 *1 1.625,0.76 2.156,1.021 0.531,0.26 10 I39 2.49,1.24 3.094,1.531 0.604,0.292 10 CANH 2.406,2.865 3.146,3.115 0.74,0.25 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (70 Ω or higher) B
NG (Below 54 Ω) C



A

8.CHECK FOR SHORT TO GND IN V BUS (CANH, CANL - CG)

B

C

8.CHECK FOR SHORT TO GND IN V BUS (CANH, CANL - CG)
a.
C210421C03
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.219,1.313 2.219,1.313 2.427,1.313 false 2.063,2.563 2.25,2.99 2.25,2.99 2.385,2.99 false 1.625,1.865 1.406,1.313 1.406,1.313 1.208,1.313 false 0.135,0.156 0.979,0.49 0.844,0.333 10 *1 1.625,0.76 2.26,1.146 0.635,0.385 10 I39 2.49,1.24 3.094,1.51 0.604,0.271 10 CANH 0.938,1.25 1.438,1.448 0.5,0.198 10 CG 2.438,2.906 3.354,3.313 0.917,0.406 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG B



A

9.CHECK FOR SHORT TO +B IN V BUS (CANH, CANL - BAT)

B

9.CHECK FOR SHORT TO +B IN V BUS (CANH, CANL - BAT)
a.
C210421C04
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.229,1.333 2.229,1.333 2.417,1.333 false 2.073,2.573 1.969,2.948 1.969,2.948 1.844,2.948 false 2.521,2.573 2.677,2.906 2.677,2.906 2.854,2.906 false 0.125,0.135 0.969,0.469 0.844,0.333 10 *1 1.625,0.76 2.177,1.052 0.552,0.292 10 I39 2.469,1.26 3.073,1.708 0.604,0.448 10 CANH 1.458,2.875 2.083,3.104 0.625,0.229 10 CANL 2.896,2.823 3.385,3.135 0.49,0.313 10 BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG B



A

10.CHECK RESULT OF COMMUNICATION BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER)

B

10.CHECK RESULT OF COMMUNICATION BUS CHECK (CONNECTION STATUS CHECK USING INTELLIGENT TESTER)
a.

Inspect or repair the probable malfunctioning part based on the check result of step 6 (the step in which Communication Bus Check was performed).


CAN Bus Check
50007
Result of Communication Bus Check (Connection Status Check Using Intelligent Tester):
Result Proceed to
All ECUs and sensors connected to the CAN communication system are displayed on the screen.
(CAN bus circuit is currently normal.)
A
·

All ECUs except the main body ECU (multiplex network body ECU) connected to sub bus 1 are not displayed on the screen.

·

The main body ECU (multiplex network body ECU) (Main Body) outputs DTC U1002.


(Open or short in sub bus 1 main lines.)
B
·

All ECUs except the power management control ECU connected to sub bus 11 are not displayed on the screen.

·

The power management control ECU (PM1 Gateway) outputs DTC U1002.


(Open or short in sub bus 11 main lines.)
C
When the V bus is selected using the pull down menu, all the ECUs and sensors connected to the V bus are displayed on the screen, but when sub bus 15 is selected, no connected ECUs or sensors are displayed.
(Open or short in sub bus 15 main lines.)
D
All ECUs connected to sub bus 1 are not displayed on the screen.
(Open in main body ECU (multiplex network body ECU) branch lines or main body ECU (multiplex network body ECU) malfunction.)
E
All ECUs connected to sub bus 11 are not displayed on the screen.
(Open in power management control ECU branch lines or power management control ECU malfunction.)
F
No ECUs or sensors connected to the ECM or sub bus 15 are displayed on the screen.
(Open in ECM main lines or ECM malfunction.)
G
One of the ECUs and sensors connected to the V Bus is not displayed on the screen.
(Open in ECU or sensor branch lines, or communication is interrupted.)
H
·

One of the ECUs and sensors connected to sub bus 1 is not displayed on the screen.*

(Open in ECU or sensor branch lines, or communication is interrupted.)

·

One of the ECUs and sensors connected to sub bus 11 is not displayed on the screen.*

(Open in ECU or sensor branch lines, or communication is interrupted.)

·

One of the ECUs and sensors connected to sub bus 15 is not displayed on the screen.

(Open in ECU or sensor branch lines, or communication is interrupted.)


I
In addition to ECUs and sensors which are connected to the CAN communication system but are not displayed on the screen, there are ECUs or sensors for which the detection status changes (changes between detected and not detected) during the inspection.
(Open in one side of ECU or sensor branch lines.)
J


NOTICE:
·

*: In this case, as the main body ECU (multiplex network body ECU) (Main Body) or power management control ECU (PM1 Gateway) outputs communication DTCs (DTCs that start with U), the problem area can be determined from those DTCs.

·

Non-installed ECUs or sensors will not be displayed. Do not mistake them for being in communication stop mode.

·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu on the intelligent tester. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)



HINT:
·

Regarding Communication Bus Check, refer to How to Interpret CAN Bus Diagnosis (Communication Bus Check) Screen.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If the detection status of ECUs changes during the inspection, one of the branch lines of a connected ECU or sensor may be open. (Signals from the ECU or sensor that has an open in one of its branch lines create electrical noise, affecting response to the intelligent tester and whether or not the ECUs and sensors are displayed.)

·

Regarding the ECUs connected to sub bus 1, the main body ECU (multiplex network body ECU) displays communicating ECUs on the intelligent tester. If the communication between the main body ECU (multiplex network body ECU) and an ECU stops for 10 seconds or more, the ECU will no longer be displayed on the intelligent tester.

·

Regarding the ECUs connected to sub bus 11, the power management control ECU displays communicating ECUs on the intelligent tester. If the communication between the power management control ECU and an ECU stops for 10 seconds or more, the ECU will no longer be displayed on the intelligent tester.

·

Regarding the communication stop mode for ECUs connected to sub bus 1, refer to the inspection procedure for the DTCs that indicate a communication stop.

·

Regarding the communication stop mode for ECUs connected to sub bus 11, refer to the inspection procedure for the DTCs that indicate a communication stop.

·

Regarding the ECUs connected to sub bus 15, the ECM displays communicating ECUs on the intelligent tester. If the communication between the ECM and an ECU stops for 3 seconds or more, the ECU will no longer be displayed on the intelligent tester.




A

11.CHECK RESULT OF CHECK COMMUNICATION MALFUNCTION DTCs (SELECT THE MALFUNCTIONING BUS)

B

C

D

E

F

G

H

I

J

11.CHECK RESULT OF CHECK COMMUNICATION MALFUNCTION DTCs (SELECT THE MALFUNCTIONING BUS)
a.

Inspect or repair the probable malfunctioning part based on the check result of step 5 (the step in which checking for communication malfunction DTCs was performed).


Check Result of Communication Malfunction DTCs (Select Malfunctioning Bus):
Result Proceed to
·

The sub bus monitor ECU has not output communication DTCs but ECUs connected to the V bus have stored communication DTCs.

(A malfunction occurred in the V Bus.)

·

ECUs connected to sub bus 15 have not output communication DTCs but ECUs connected to the V bus have stored communication DTCs.

(A malfunction occurred in the V Bus.)

·

The ECM (Engine and ECT) has not output DTC U0293 (Lost Communication with HV ECU).


·

The power management control ECU (Hybrid Control) has not output DTC U0100 (Lost Communication with ECM/PCM "A") or DTC U0129 (Lost Communication with Brake System Control Module).


·

The brake booster with master cylinder assembly (skid control ECU) (ABS/VSC/TRC) has not output DTC U0293 (Communication Error from HV ECU).



A
The main body ECU (multiplex network body ECU) (Main Body) outputs DTC U1002.
(A malfunction occurred in sub bus 1.)
B
The power management control ECU (PM1 Gateway) outputs DTC U1002.
(A malfunction occurred in sub bus 11.)
C
ECUs connected to sub bus 15 store communication error DTCs.
(A malfunction occurred in sub bus 15.)
·

The ECM (Engine and ECT) outputs only DTC U0293 (Lost Communication with HV ECU).

·

The power management control ECU (Hybrid Control) outputs only DTC U0100 (Lost Communication with ECM/PCM "A") and DTC U0129 (Lost Communication with Brake System Control Module).

·

The brake booster with master cylinder assembly (skid control ECU) (ABS/VSC/TRC) outputs only DTC U0293 (Communication Error from HV ECU).


D
·

The main body ECU (multiplex network body ECU) (Main Body) outputs DTCs other than DTC U1002.

(A malfunction occurred in an ECU branch line connected to sub bus 1.)

·

The power management control ECU (PM1 Gateway) outputs DTCs other than DTC U1002.

(A malfunction occurred in an ECU branch line connected to sub bus 11.)

·

The power management control ECU (Hybrid Control) outputs only DTC U0129 (Lost Communication with Brake System Control Module).

(A malfunction occurred in an ECU branch line connected to sub bus 15.)


E


HINT:
·

Only sub bus 1 and sub bus 11 have a sub bus monitor ECU.

·

The term ''sub bus monitor ECU'' refers to a gateway function equipped ECU that is able to monitor a bus and store DTCs.

·

When checking for communication DTCs, refer to How to Interpret Communication DTCs (DTCs that start with U).

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Because a gateway function equipped ECU (sub bus monitor ECU) monitors signals from all ECUs that are connected to its sub bus, a gateway function equipped ECU can detect ECUs with a communication stop more accurately. In this case, perform troubleshooting by referring to the DTC combination table for the sub bus.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If communication DTCs are stored, and all ECUs and sensors connected to the CAN communication system are displayed on the Communication Bus Check (CAN bus check) screen of the intelligent tester, a past malfunction that is currently not occurring is suspected.

·

When a CAN branch of the V bus is malfunctioning, because the ECUs and sensors related to it detect the malfunction, the problem area can be determined using the combination of DTCs that are output.

·

When sub bus 1 is malfunctioning, the main body ECU (multiplex network body ECU) detects a communication stop for connected ECUs and a network communication error, and stores DTCs.

·

When sub bus 11 is malfunctioning, the power management control ECU detects a communication stop for connected ECUs and a network communication error, and stores DTCs.

·

On the intelligent tester, the Main Body item displays the DTCs for ECUs connected to sub bus 1.

·

On the intelligent tester, the PM1 Gateway item displays the DTCs for ECUs connected to sub bus 11.

·

When both the sub bus monitor ECU and the ECUs connected to the V bus store communication DTCs, check and repair the corresponding sub bus first.




A

12.DTC COMBINATION TABLE

B

C

D

E

12.DTC COMBINATION TABLE
a.

Confirm the problem according to the combination of output DTCs regarding the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
Combination of DTCs is not in DTC Combination Table. A
Combination of DTCs is in DTC Combination Table. B


HINT:

CAN communication system history DTCs may indicate the problem if CAN communication system DTCs are output and all ECUs and sensors connected to the CAN communication system are displayed on "Communication Bus Check" of the intelligent tester.



A

13.IDENTIFICATION OF PROBLEM (PAST MALFUNCTION IN MAIN BUS OF V BUS)

B

13.IDENTIFICATION OF PROBLEM (PAST MALFUNCTION IN MAIN BUS OF V BUS)
a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Clear the DTCs using the intelligent tester.


c.

Perform the tests in Symptom Simulation to check the wire harnesses and connectors including those for V bus main bus lines.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


d.

Based on the results of the check, inspect the parts that output DTCs to determine the malfunctioning part.

HINT:

If DTCs are output, do not turn the power switch off.



Result:
Proceed to
NEXT



NEXT

14.REPAIR OR REPLACEMENT
14.REPAIR OR REPLACEMENT
Result:
Proceed to
NEXT



NEXT

15.CONFIRMATION TEST
15.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END