Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3000-388  Battery Control System  


DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals received from the battery smart unit. This DTC is set when the SOC (state of charge) of the HV battery starts to drop as a result of leaving the shift lever in N, running out of fuel, or a malfunction in the hybrid control system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3000-388 Battery Control System Discharge inhibition control malfunction
·

Fuel level

·

HV battery


Does not come on Master Warning Light:
Does not come on

CAUTION / NOTICE / HINT

HINT:
·

If the vehicle is stopped or parked with the shift lever in the N position for a long time, DTC P3000-388 may be set because the HV battery cannot be charged.

·

When the engine cannot be started, DTC P3000-388 may be set because the HV battery cannot be charged.

·

Repeated engine start checks may cause the SOC to drop, resulting in DTC P3000-388 being set. In this case, charge the HV battery using the THS charger.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

·

Charging the HV battery using the THS charger takes approximately 10 minutes when the battery temperature is 25°C (77°F) or approximately 30 minutes when the battery temperature is 0°C (32°F).

·

The THS charger is a supplemental charging device that enables the engine to start (READY-on state).



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P3000-388 or P3000-389 only is output. A
DTCs other than P3000-388, P3000-389, and P0AF8 are also output. B



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (ENGINE AND ECT)

B

2.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Check if DTCs are output.

Result:
Result Proceed to
NO DTCs are output. A
DTCs are output. B



e.

Turn the power switch off.



A

3.CHECK AMOUNT OF FUEL

B

3.CHECK AMOUNT OF FUEL
a.

Turn the power switch on (IG).


b.

Check the amount of fuel by referring to the fuel gauge in the meter.

Result:
Result Proceed to
Proper amount of fuel is in the tank. A
There is no fuel in the tank. B


HINT:

Add fuel until the low fuel level warning light turns off.



c.

Turn the power switch off.



A

4.CHECK ENGINE START

B

REFUEL VEHICLE

4.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

HINT:
·

Depressing the accelerator pedal with the shift lever in P will cause the engine to start.

·

Turning the power switch on (READY) and off repeatedly while the SOC is low may cause the SOC to drop further, resulting in DTC P3000-389 being set. Charge the HV battery using the THS charger as necessary.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.



Result:
Result Proceed to
The engine starts. A
The engine does not start. B



c.

If the engine does not start, turn the power switch off.



A

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

B

CHARGE HV BATTERY (CHECK THAT ENGINE STARTS)