Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3108-536  Lost Communication with A/C System Control Module  


DESCRIPTION

The power management control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3108-536 Lost Communication with A/C System Control Module A/C inverter malfunction
·

Wire harness or connector

·

Compressor with motor assembly

·

Power management control ECU


Does not come on Master Warning Light:
Does not come on

WIRING DIAGRAM

A306449E01
5.948,0.5 6.313,0.708 0.365,0.208 10 false +B 5.969,0.927 6.333,1.135 0.365,0.208 10 false +B 1.521,1.521 1.885,1.729 0.365,0.208 10 false +B 1.51,1.906 1.875,2.115 0.365,0.208 10 false +B 0.458,0.677 1.073,0.969 0.615,0.292 10 false A/C-IG1 1.146,0.385 1.51,0.594 0.365,0.208 10 false 6 1.375,0.531 1.792,0.74 0.417,0.208 10 false IG1 2.167,0.573 2.583,0.781 0.417,0.208 10 false CLK 2.188,1.021 2.604,1.229 0.417,0.208 10 false DIN 2.104,1.51 2.521,1.719 0.417,0.208 10 false DOUT 2.104,2.031 2.521,2.24 0.417,0.208 10 false STBI 2.104,2.406 2.521,2.615 0.417,0.208 10 false GND 5.344,0.583 5.76,0.792 0.417,0.208 10 false CLK 5.375,1.052 5.792,1.26 0.417,0.208 10 false ITE 5.354,1.458 5.771,1.667 0.417,0.208 10 false ETI 5.375,2 5.792,2.208 0.417,0.208 10 false STB 5.281,2.813 5.698,3.021 0.417,0.208 10 false A38 5.073,0.594 5.354,0.792 0.281,0.198 10 false 19 5.052,1.042 5.302,1.25 0.25,0.208 10 false 31 5.052,1.51 5.281,1.708 0.229,0.198 10 false 30 5.052,1.979 5.313,2.188 0.26,0.208 10 false 20 2.615,2.313 3.031,2.521 0.417,0.208 10 false 5 2.594,1.969 3.01,2.177 0.417,0.208 10 false 4 2.604,1.5 3.021,1.708 0.417,0.208 10 false 3 2.604,1.052 3.021,1.26 0.417,0.208 10 false 2 2.583,0.573 3,0.781 0.417,0.208 10 false 1 1.333,2.865 1.75,3.073 0.417,0.208 10 false E65 1.323,3.031 2.854,3.688 1.531,0.656 10 false Compressor with Motor Assembly 5.26,3.01 6.792,3.5 1.531,0.49 10 false Power Management Control ECU

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)
a.
A258638E06
0.146,0.167 0.531,0.438 0.385,0.271 0.188,0.198 0.49,0.396 0.302,0.198 10 true E65

Check the connection of connector E65 of the compressor with motor assembly.

OK:

The connector is connected securely and there are no contact problems.


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect connector E65 from the compressor with motor assembly.


b.
A211448C35
0.396,1.01 0.813,1.25 0.417,0.24 1.906,1.135 2.063,1.656 true 2.042,1.135 2.5,1.656 true 0.25,0.198 0.479,0.375 0.229,0.177 10 false *a 0.448,1.042 0.792,1.292 0.344,0.25 10 false E65 1.958,1.698 2.292,1.865 0.333,0.167 10 false GND 2.521,1.698 2.781,1.865 0.26,0.167 10 false IG1
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E65-5 (GND) - Body ground Power switch off Below 1 Ω



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E65-6 (IG1) - E65-5 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the compressor with motor assembly connector.

Result:
Proceed to
OK
NG




OK

4.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3108-536 is output. A
P3108-536 is not output. B



e.

Turn the power switch off.



A

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Disconnect connector E65 from the compressor with motor assembly.


c.

Turn the power switch on (IG).


d.
A206712C16
0.135,1.792 0.552,2.031 0.417,0.24 0.458,3.625 0.875,3.865 0.417,0.24 0.99,1.969 1.438,1.635 true 0.958,2.031 1.333,1.938 true 0.896,2.052 1.146,2.385 true 1.323,3.75 1.063,4.271 true 1.635,3.75 1.938,4.271 true 1.49,3.76 1.49,4.271 true 0.188,1.823 0.521,2.021 0.333,0.198 10 false A38 0.5,3.656 0.927,3.823 0.427,0.167 10 false E65 0.167,0.156 0.344,0.323 0.177,0.167 10 false *1 0.167,3.021 0.344,3.188 0.177,0.167 10 false *2 1.521,1.531 1.833,1.698 0.313,0.167 10 false CLK 1.375,1.854 1.688,2.021 0.313,0.167 10 false ETI 1.188,2.406 1.5,2.573 0.313,0.167 10 false ITE 0.885,4.302 1.198,4.469 0.313,0.167 10 false CLK 1.365,4.302 1.646,4.469 0.281,0.167 10 false DIN 1.823,4.302 2.25,4.469 0.427,0.167 10 false DOUT
*1 Rear view of wire harness connector
(to Power Management Control ECU)
*2 Front view of wire harness connector
(to Compressor with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-19 (CLK) - Body ground Power switch on (IG) Below 1 V
A38-30 (ETI) - Body ground Power switch on (IG) Below 1 V
A38-31 (ITE) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A38-19 (CLK) - E65-1 (CLK) Power switch off Below 1 Ω
A38-30 (ETI) - E65-3 (DOUT) Power switch off Below 1 Ω
A38-31 (ITE) - E65-2 (DIN) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A38-19 (CLK) or E65-1 (CLK) - Body ground and other terminals Power switch off 10 kΩ or higher
A38-30 (ETI) or E65-3 (DOUT) - Body ground and other terminals Power switch off 10 kΩ or higher
A38-31 (ITE) or E65-2 (DIN) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the compressor with motor assembly connector.


h.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

6.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER MANAGEMENT CONTROL ECU
a.

Disconnect connector E65 from the compressor with motor assembly.


b.
A211448C36
0.354,0.979 0.771,1.219 0.417,0.24 1.323,1.156 1.031,1.74 true 1.656,1.167 1.979,1.729 true 1.521,1.167 1.521,1.74 true 0.167,0.146 0.5,0.385 0.333,0.24 10 false *a 0.406,1.01 0.813,1.219 0.406,0.208 10 false E65 0.813,1.75 1.135,1.917 0.323,0.167 10 false CLK 1.385,1.75 1.708,1.917 0.323,0.167 10 false DIN 1.917,1.75 2.344,1.917 0.427,0.167 10 false DOUT
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E65-3 (DOUT) - Body ground Power switch off 10 kΩ or higher



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E65-1 (CLK) - Body ground Power switch on (IG) 11 to 14 V
E65-2 (DIN) - Body ground Power switch on (IG) 11 to 14 V
E65-3 (DOUT) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the compressor with motor assembly connector.

Result:
Proceed to
OK
NG




OK

7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
a.

Disconnect connector A38 from the power management control ECU.


b.
A204443C40
0.688,2.917 1.104,3.156 0.417,0.24 0.958,2.5 1.354,2.156 true 0.917,2.563 1.375,2.375 true 0.875,2.573 1.354,2.771 true 0.74,2.948 1.104,3.146 0.365,0.198 10 false A38 1.396,2.01 1.719,2.177 0.323,0.167 10 false CLK 1.396,2.281 1.719,2.448 0.323,0.167 10 false ETI 1.396,2.688 1.719,2.854 0.323,0.167 10 false ITE 0.26,0.271 0.531,0.552 0.271,0.281 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-19 (CLK) - Body ground Power switch off 10 kΩ or higher
A38-31 (ITE) - Body ground Power switch off 10 kΩ or higher



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-30 (ETI) - Body ground Power switch on (IG) 11 to 14 V
A38-19 (CLK) - Body ground Power switch on (IG) Below 1 V
A38-31 (ITE) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Disconnect connector E65 from the compressor with motor assembly.


c.

Turn the power switch on (IG).


d.
A206712C17
1.177,2.063 1.594,2.302 0.417,0.24 0.427,3.625 0.844,3.865 0.417,0.24 0.948,1.969 1.375,1.76 true 1.76,3.75 2.063,4.271 true 1.219,2.094 1.635,2.313 0.417,0.219 10 false A38 0.469,3.656 0.896,3.896 0.427,0.24 10 false E65 0.135,0.156 0.49,0.375 0.354,0.219 10 false *a 0.135,3.021 0.5,3.26 0.365,0.24 10 false *b 1.406,1.615 1.719,1.781 0.313,0.167 10 false STB 1.927,4.302 2.354,4.469 0.427,0.167 10 false STBI
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Compressor with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-20 (STB) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A38-20 (STB) - E65-4 (STBI) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A38-20 (STB) or E65-4 (STBI) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the compressor with motor assembly connector.


h.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

9.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK POWER MANAGEMENT CONTROL ECU
a.

Disconnect connector E65 from the compressor with motor assembly.


b.
A211448C37
0.396,1.01 0.813,1.25 0.417,0.24 1.781,1.146 1.958,1.667 true 0.24,0.188 0.542,0.406 0.302,0.219 10 false *a 0.448,1.042 0.865,1.344 0.417,0.302 10 false E65 1.844,1.698 2.25,1.865 0.406,0.167 10 false STBI
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E65-4 (STBI) - Body ground Power switch off 10 kΩ or higher



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E65-4 (STBI) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the compressor with motor assembly connector.

Result:
Proceed to
OK
NG




OK

10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
a.

Disconnect connector A38 from the power management control ECU.


b.
A204443C41
0.688,2.917 1.104,3.156 0.417,0.24 0.927,2.5 1.406,2.26 true 0.74,2.948 1.208,3.146 0.469,0.198 10 false A38 1.438,2.104 1.76,2.271 0.323,0.167 10 false STB 0.26,0.271 0.698,0.479 0.438,0.208 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-20 (STB) - Body ground Power switch off 10 kΩ or higher



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-20 (STB) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY