Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3147-239  Transmission system  P3147-241  Transmission system  


DESCRIPTION

The hybrid vehicle transaxle assembly consists of the power split planetary gear unit, MG1, MG2, and the 2-stage motor speed reduction planetary gear unit. The power split planetary gear unit uses a planetary gear to split engine output in accordance with driving requests while the vehicle is driven or the HV battery is charged. MG2 assists engine output while increasing vehicle drive force. MG2 also converts the energy, which would otherwise be consumed in the form of heat during normal braking, into electrical energy. This recovered energy is put back into the HV battery to perform regenerative braking. MG1 generates power, which is used for charging the HV battery or driving MG2, and also regulates the amount of electricity being generated. In addition, MG1 is used as a starter motor to start the engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3147-239 Transmission system Hybrid vehicle transaxle input malfunction (shaft damaged)
·

Engine

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector

·

Power management control ECU

·

Transmission input damper assembly


Does not come on Master Warning Light:
Comes on
P3147-241 Transmission system Hybrid vehicle transaxle input malfunction l ECU (input system lock)
·

Engine

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector

·

Power management control ECU

·

Transmission input damper assembly


Does not come on Master Warning Light:
Comes on

PROCEDURE

1.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Check if DTCs are output.

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
DTCs other than P3147-239 or P3147-241 are not output. A
P3147-240 or P3147-242 is also output. B
P0A1D is also output. C



e.

Turn the power switch off.



A

3.CHECK CRANKSHAFT PULLEY REVOLUTION (SHIFT LEVER IN P)

B

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

C

3.CHECK CRANKSHAFT PULLEY REVOLUTION (SHIFT LEVER IN P)
a.

With the shift lever in P and lift up the vehicle.


b.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


Result:
Result Proceed to
The crankshaft rotates. A
The crankshaft does not rotate. B



c.

Lower the vehicle.



A

4.CLEAR DTC

B

8.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
4.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236

f.

Turn the power switch off.

Result:
Proceed to
NEXT




NEXT

5.CHECK ENGINE RACING
5.CHECK ENGINE RACING

OK

6.CHECK CREEP MOVEMENT

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

6.CHECK CREEP MOVEMENT
a.

Depress the brake pedal, move the shift lever to D, and release the brake pedal.

OK:

The wheels turn (the vehicle creeps forward).


HINT:

If the wheels do not turn and the reading on the intelligent tester shows DTC P3147-239, replace the hybrid vehicle transaxle assembly.


Result:
Proceed to
OK
NG




OK

7.INSPECT ENGINE SPEED

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

7.INSPECT ENGINE SPEED

OK

NG

REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY

8.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
a.

Turn the power switch on (IG) and move the shift lever to N.


b.

Lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


OK:

The crankshaft rotates.



d.

Lower the vehicle.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE ENGINE