Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  U0110-159  Lost Communication with Drive Motor Control Module "A"  U0110-656  Lost Communication with Drive Motor Control Module "A"  U0110-657  Lost Communication with Drive Motor Control Module "A"  


DESCRIPTION

For a description of the inverter.

See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266

The MG ECU located in the inverter with converter assembly controls MG2 based on commands from the power management control ECU. The MG ECU monitors communication data and detects malfunctions.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U0110-159 Lost Communication with Drive Motor Control Module "A" Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Power management control ECU

·

INV fuse


Does not come on Master Warning Light:
Comes on
U0110-656 Lost Communication with Drive Motor Control Module "A" Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Power management control ECU

·

INV fuse


Does not come on Master Warning Light:
Comes on
U0110-657 Lost Communication with Drive Motor Control Module "A" Error in reception from inverter with converter assembly (MG ECU) via serial communication (no reception)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Power management control ECU

·

INV fuse


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A262682E10
4.219,0.427 4.615,0.688 0.396,0.26 10 false CLK+ 2.469,0.396 2.865,0.615 0.396,0.219 10 false CLK+ 4.208,0.885 4.604,1.135 0.396,0.25 10 false CLK- 2.469,0.885 2.875,1.115 0.406,0.229 10 false CLK- 4.229,1.26 4.656,1.552 0.427,0.292 10 false REQ+ 2.448,1.24 2.885,1.51 0.438,0.271 10 false REQ+ 4.229,2.115 4.625,2.344 0.396,0.229 10 false HTM+ 2.448,2.115 2.865,2.385 0.417,0.271 10 false HTM+ 4.24,2.958 4.667,3.115 0.427,0.156 10 false MTH+ 2.448,2.979 2.885,3.25 0.438,0.271 10 false MTH+ 0.917,3.063 1.135,3.354 0.219,0.292 10 false E1 4.229,2.604 4.625,2.833 0.396,0.229 10 false HTM- 2.448,2.604 2.896,2.854 0.448,0.25 10 false HTM- 4.229,3.448 4.604,3.802 0.375,0.354 10 false MTH- 4.115,4.01 4.542,4.167 0.427,0.156 10 false A14 4.115,4.167 6.24,4.5 2.125,0.333 10 false Inverter with Converter Assembly 2.448,3.469 2.844,3.74 0.396,0.271 10 false MTH- 4.229,1.75 4.635,2 0.406,0.25 10 false REQ- 2.448,1.75 2.802,1.969 0.354,0.219 10 false REQ- 5.865,0.521 6.094,0.677 0.229,0.156 10 false +B 5.792,0.969 6.094,1.125 0.302,0.156 10 false +B2 5.677,3.073 6.083,3.344 0.406,0.271 10 false GND1 5.677,3.542 6.073,3.823 0.396,0.281 10 false GND2 2.927,0.51 3.219,0.729 0.292,0.219 10 false A39 2.969,0.292 3.167,0.448 0.198,0.156 10 false 21 2.969,0.771 3.167,0.927 0.198,0.156 10 false 20 2.969,1.188 3.167,1.344 0.198,0.156 10 false 33 2.969,1.646 3.167,1.802 0.198,0.156 10 false 32 2.969,2.031 3.167,2.188 0.198,0.156 10 false 24 2.969,2.51 3.167,2.667 0.198,0.156 10 false 25 2.969,2.896 3.167,3.052 0.198,0.156 10 false 30 2.969,3.365 3.167,3.521 0.198,0.156 10 false 29 2.927,0.99 3.24,1.208 0.313,0.219 10 false A39 2.927,1.375 3.25,1.646 0.323,0.271 10 false A39 2.927,1.844 3.229,2.042 0.302,0.198 10 false A39 2.927,2.208 3.26,2.417 0.333,0.208 10 false A39 2.927,2.708 3.229,2.938 0.302,0.229 10 false A39 2.927,3.083 3.24,3.292 0.313,0.208 10 false A39 2.927,3.552 3.229,3.76 0.302,0.208 10 false A39 3.927,0.417 4.104,0.667 0.177,0.25 10 false 7 3.844,0.885 4.115,1.167 0.271,0.281 10 false 18 3.854,1.271 4.083,1.427 0.229,0.156 10 false 26 3.844,1.75 4.052,1.927 0.208,0.177 10 false 37 3.927,2.115 4.052,2.271 0.125,0.156 10 false 9 3.844,2.604 4.042,2.76 0.198,0.156 10 false 20 3.906,2.979 4.031,3.135 0.125,0.156 10 false 8 3.854,3.469 4.052,3.625 0.198,0.156 10 false 19 0.646,3.052 0.938,3.208 0.292,0.156 10 false I3 0.656,2.833 0.854,2.99 0.198,0.156 10 false 6 0.823,4.073 2.938,4.365 2.115,0.292 10 false Power Management Control ECU 6.094,0.427 6.302,0.667 0.208,0.24 10 false 30 6.125,0.875 6.323,1.146 0.198,0.271 10 false 31 6.146,2.979 6.417,3.229 0.271,0.25 10 false 10 6.146,3.448 6.417,3.646 0.271,0.198 10 false 11 6.552,0.677 6.906,0.833 0.354,0.156 10 false INV 4.771,0.76 4.938,0.927 0.167,0.167 10 false * 2.208,0.76 2.344,0.927 0.135,0.167 10 false * 2.208,1.625 2.344,1.792 0.135,0.167 10 false * 2.208,2.49 2.344,2.656 0.135,0.167 10 false * 2.208,3.344 2.344,3.51 0.135,0.167 10 false * 4.771,1.625 4.938,1.792 0.167,0.167 10 false * 4.771,2.479 4.938,2.646 0.167,0.167 10 false * 4.771,3.333 4.938,3.5 0.167,0.167 10 false * 0.427,4.51 1.906,4.677 1.479,0.167 10 false *: Approximately 120 Ω 6.479,1.271 7.135,1.917 0.656,0.646 10 false from IGCT Relay

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

If any of the DTCs U0110-159, U0110-656, and U0110-657 was set due to incomplete engagement of the connectors, and if the system returns to normal when the power switch is turned on (IG) after clearing the DTCs, DTC P324E-788 will be set. Proceed to troubleshooting without considering DTC P324E-788.



PROCEDURE

1.CHECK FUSE (INV)
a.
A259930C03
0.145,0.115 0.301,0.262 0.156,0.147 10 *1 2.921,0.872 3.077,1.019 0.156,0.147 10 *2 1.721,0.868 2.889,0.948 false
*1 No. 2 Engine Room Relay Block
*2 INV Fuse


Remove the INV fuse from the No. 2 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INV fuse terminals Always Below 1 Ω



c.

Install the INV fuse.

Result:
Proceed to
OK
NG




OK

2.CLEAR DTC

NG

12.REPLACE FUSE (INV)
2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
DTC U0110-159, 656 or 657 is output. A
DTC U0110-159, 656 and 657 are not output. B



e.

Turn the power switch off.



A

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

B

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

7.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

7.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.
A258451C57
0.198,1.063 0.656,1.344 0.458,0.281 1.781,1.844 2.115,1.323 false 2.583,1.844 2.25,1.323 false 1.771,0.531 2.104,1.052 false 2.573,0.531 2.24,1.052 false 0.302,1.125 0.677,1.354 0.375,0.229 10 false A14 1.646,1.865 1.927,2.063 0.281,0.198 10 false +B 2.438,1.885 2.823,2.115 0.385,0.229 10 false +B2 1.51,0.323 1.927,0.521 0.417,0.198 10 false GND1 2.344,0.323 2.802,0.531 0.458,0.208 10 false GND2 0.125,0.104 0.302,0.271 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A14-10 (GND1) - Body ground Power switch off Below 1 Ω
A14-11 (GND2) - Body ground Power switch off Below 1 Ω



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A14-30 (+B) - Body ground Power switch on (IG) 11 to 14 V
A14-31 (+B2) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

9.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the power management control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A204496C08
1.198,0.396 1.615,0.635 0.417,0.24 1.75,0.396 2.167,0.635 0.417,0.24 1.583,1.198 1.115,1.719 true 1.635,1.208 1.719,1.729 true 1.76,1.094 2.115,1.729 true 1.281,0.427 1.594,0.615 0.313,0.188 10 false A39 1.917,0.427 2.104,0.615 0.188,0.188 10 false I3 0.854,1.75 1.24,1.917 0.385,0.167 10 false CLK+ 1.521,1.771 2,2 0.479,0.229 10 false CLK- 2.063,1.76 2.427,2.042 0.365,0.281 10 false E1 0.177,3.083 0.469,3.344 0.292,0.26 10 false CH1 0.188,3.813 0.51,4.052 0.323,0.24 10 false CH2 2.552,3.438 3.021,3.708 0.469,0.271 10 false GND 2.563,4.01 2.99,4.219 0.427,0.208 10 false GND 0.146,0.125 0.344,0.292 0.198,0.167 10 false *a
*a Component with harness connected
(Power Management Control ECU)


Measure the waveform.

Item Contents
Tester Connection CH1: A39-21 (CLK+) - I3-6 (E1)
CH2: A39-20 (CLK-) - I3-6 (E1)
Equipment Setting 1V/DIV., 1μs/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

10.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

B

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
10.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the power management control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A204500C07
1.208,0.385 1.625,0.625 0.417,0.24 1.74,0.385 2.156,0.625 0.417,0.24 1.354,1.26 1.146,1.719 true 1.396,1.26 1.604,1.719 true 1.76,1.083 2.115,1.719 true 1.292,0.417 1.615,0.615 0.323,0.198 10 false A39 1.896,0.417 2.104,0.604 0.208,0.188 10 false I3 0.938,1.771 1.354,1.938 0.417,0.167 10 false REQ+ 1.49,1.771 1.896,2.01 0.406,0.24 10 false REQ- 2.083,1.771 2.354,2.01 0.271,0.24 10 false E1 0.177,3.135 0.49,3.302 0.313,0.167 10 false CH1 0.146,3.813 0.458,3.979 0.313,0.167 10 false CH2 2.5,3.479 2.875,3.646 0.375,0.167 10 false GND 2.51,3.813 2.885,3.979 0.375,0.167 10 false GND 0.146,0.115 0.344,0.281 0.198,0.167 10 false *a
*a Component with harness connected
(Power Management Control ECU)


Measure the waveform.

Item Contents
Tester Connection CH1: A39-33 (REQ+) - I3-6 (E1)
CH2: A39-32 (REQ-) - I3-6 (E1)
Equipment Setting 1V/DIV., 1ms/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

11.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

B

15.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
11.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the power management control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A204498C07
1.198,0.385 1.615,0.625 0.417,0.24 1.75,0.385 2.167,0.625 0.417,0.24 2.583,4.063 2.698,4.188 0.115,0.125 1.563,1.24 1.177,1.688 true 1.604,1.24 1.677,1.688 true 1.781,1.052 2.135,1.688 true 2.771,3.563 2.635,3.563 false 2.771,4.125 2.635,4.125 false 1.292,0.417 1.563,0.625 0.271,0.208 10 false A39 1.917,0.417 2.146,0.635 0.229,0.219 10 false I3 0.865,1.74 1.281,1.906 0.417,0.167 10 false MTH+ 1.458,1.74 1.896,1.906 0.438,0.167 10 false MTH- 2.156,1.729 2.354,1.896 0.198,0.167 10 false E1 0.26,3.125 0.583,3.417 0.323,0.292 10 false CH1 0.229,3.844 0.531,4.167 0.302,0.323 10 false CH2 2.823,3.479 3.198,3.646 0.375,0.167 10 false GND 2.823,4.042 3.198,4.208 0.375,0.167 10 false GND 0.146,0.115 0.344,0.281 0.198,0.167 10 false *a
*a Component with harness connected
(Power Management Control ECU)


Measure the waveform.

Item Contents
Tester Connection CH1: A39-30 (MTH+) - I3-6 (E1)
CH2: A39-29 (MTH-) - I3-6 (E1)
Equipment Setting 1V/DIV,, 200μs/DIV,
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

B

17.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
12.REPLACE FUSE (INV)
a.
A259930C04
0.145,0.115 0.301,0.262 0.156,0.147 10 *1 2.921,0.872 3.077,1.019 0.156,0.147 10 *2 1.721,0.868 2.889,0.948 false
*1 No. 2 Engine Room Relay Block
*2 INV Fuse


Replace the INV fuse.


b.

Turn the power switch on (READY).


c.

Check if there is an open circuit in the INV fuse in the No.2 engine room relay block.

OK:

There is no open circuit in the INV fuse.


HINT:

If the fuse does not become open again after turning the power switch on (READY), it can be assumed that the previous fuse failed due to age.



d.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

COMPLETED

NG

19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - INV FUSE)
13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A39 from the power management control ECU.


c.

Disconnect connector A14 from the inverter with converter assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A259928C13
0.354,3.521 0.813,3.802 0.458,0.281 0.531,1.979 0.99,2.26 0.458,0.281 2.021,2.531 1.635,2.219 true 2.021,2 1.698,2.208 true 1.604,3.042 1.75,3.521 true 2.198,3.052 1.771,3.604 true 0.469,3.573 0.74,3.74 0.271,0.167 10 false A14 0.635,2.031 0.917,2.24 0.281,0.208 10 false A39 1.396,2.802 1.771,2.969 0.375,0.167 10 false CLK+ 2.073,2.458 2.448,2.625 0.375,0.167 10 false CLK+ 2.104,2.865 2.479,3.031 0.375,0.167 10 false CLK- 2.073,1.917 2.448,2.083 0.375,0.167 10 false CLK- 0.448,2.906 0.625,3.073 0.177,0.167 10 false *b 0.198,0.125 0.375,0.292 0.177,0.167 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-21 (CLK+) - Body ground Power switch on (IG) Below 1 V
A39-20 (CLK-) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-21 (CLK+) - A14-7(CLK+) Power switch off Below 1 Ω
A39-20 (CLK-) - A14-18 (CLK-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-21 (CLK+) or A14-7 (CLK+) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-20 (CLK-) or A14-18 (CLK-) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Connect the inverter with converter assembly connector.


k.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

14.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect connector A39 from the power management control ECU.


b.
A204444C28
0.583,2.375 1,2.615 0.417,0.24 1.625,2.51 1.354,3.104 true 1.688,2.521 1.885,3.042 true 0.667,2.396 0.938,2.563 0.271,0.167 10 false A39 1.177,3.125 1.563,3.292 0.385,0.167 10 false CLK+ 1.75,3.146 2.188,3.313 0.438,0.167 10 false CLK- 0.229,0.198 0.427,0.365 0.198,0.167 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A39-21 (CLK+) - A39-20 (CLK-) Power switch off 80 to 170 Ω



c.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

15.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A39 from the power management control ECU.


c.

Disconnect connector A14 from the inverter with converter assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A259928C14
0.302,3.573 0.76,3.854 0.458,0.281 0.583,1.938 1.042,2.219 0.458,0.281 1.219,4.281 1.677,3.75 true 1.99,4.26 1.688,3.813 true 1.083,2.729 1.365,2.271 false 1.719,2.74 1.417,2.292 true 0.406,3.635 0.677,3.802 0.271,0.167 10 false A14 0.698,2 0.969,2.167 0.271,0.167 10 false A39 1.042,4.302 1.448,4.469 0.406,0.167 10 false REQ+ 1.865,4.302 2.24,4.469 0.375,0.167 10 false REQ- 0.198,2.979 0.375,3.146 0.177,0.167 10 false *b 0.188,0.135 0.365,0.302 0.177,0.167 10 false *a 0.813,2.76 1.26,2.99 0.448,0.229 10 false REQ+ 1.656,2.771 2.083,2.969 0.427,0.198 10 false REQ-
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-33 (REQ+) - Body ground Power switch on (IG) Below 1 V
A39-32 (REQ-) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-33 (REQ+) - A14-26 (REQ+) Power switch off Below 1 Ω
A39-32 (REQ-) - A14-37 (REQ-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-33 (REQ+) or A14-26 (REQ+) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-33 (REQ+) or A14-26 (REQ+) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Connect the inverter with converter assembly connector.


k.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

16.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect connector A39 from the power management control ECU.


b.
A204444C29
0.615,2.344 1.031,2.583 0.417,0.24 1.344,2.573 1.135,2.969 true 1.396,2.583 1.604,2.979 true 0.698,2.375 0.969,2.542 0.271,0.167 10 false A39 0.917,3.01 1.333,3.25 0.417,0.24 10 false REQ+ 1.49,3.021 1.885,3.219 0.396,0.198 10 false REQ- 0.25,0.229 0.448,0.396 0.198,0.167 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A39-33 (REQ+) - A39-32 (REQ-) Power switch off 80 to 170 Ω



c.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

17.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A39 from the power management control ECU.


c.

Disconnect connector A14 from the inverter with converter assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A259928C11
0.354,3.573 0.813,3.854 0.458,0.281 0.531,1.938 0.99,2.219 0.458,0.281 1.865,2.688 1.646,2.292 true 1.365,2.677 1.604,2.292 true 2.302,3.042 1.833,3.531 true 2.313,4.271 1.823,3.594 true 0.438,3.625 0.708,3.792 0.271,0.167 10 false A14 0.604,1.99 0.875,2.156 0.271,0.167 10 false A39 2.354,2.948 2.813,3.167 0.458,0.219 10 false MTH+ 1.115,2.698 1.51,2.865 0.396,0.167 10 false MTH+ 2.208,4.313 2.625,4.552 0.417,0.24 10 false MTH- 1.698,2.708 2.073,2.875 0.375,0.167 10 false MTH- 0.365,2.958 0.542,3.125 0.177,0.167 10 false *b 0.198,0.177 0.375,0.344 0.177,0.167 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-30 (MTH+) - Body ground Power switch on (IG) Below 1 V
A39-29 (MTH-) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A39-30 (MTH+) - A14-8 (MTH+) Power switch off Below 1 Ω
A39-29 (MTH-) - A14-19 (MTH-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A39-30 (MTH+) or A14-8(MTH+) - Body ground and other terminals Power switch off 10 kΩ or higher
A39-29 (MTH-) or A14-19 (MTH-) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Connect the inverter with converter assembly connector.


k.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

18.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.
A249168C04
1.198,0.99 1.615,1.229 0.417,0.24 1.573,1.917 1.365,2.438 true 1.625,1.917 1.833,2.438 true 1.281,1.021 1.563,1.208 0.281,0.188 10 false A39 1.094,2.458 1.531,2.625 0.438,0.167 10 false MTH+ 1.729,2.469 2.167,2.635 0.438,0.167 10 false MTH- 0.229,0.229 0.427,0.396 0.198,0.167 10 false *a
*a Component with harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A39-30 (MTH+) - A39-29 (MTH-) Power switch off 80 to 170 Ω



d.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - INV FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259930C05
0.145,0.115 0.301,0.262 0.156,0.147 10 *1 2.921,0.872 3.077,1.019 0.156,0.147 10 *2 1.721,0.868 2.889,0.948 false
*1 No. 2 Engine Room Relay Block
*2 INV Fuse


Remove the INV fuse from the No. 2 engine room relay block.


c.

Disconnect connector A14 from the inverter with converter assembly.


d.

Measure the resistance according to the value(s) in the table below.

A259931C03
0.677,1.26 1.052,1.49 0.375,0.229 2.115,2.063 2.344,1.5 true 2.646,2.052 2.469,1.521 true 0.76,1.292 1.031,1.458 0.271,0.167 10 false A14 1.969,2.104 2.167,2.271 0.198,0.167 10 false +B 2.583,2.083 2.865,2.25 0.281,0.167 10 false +B2 0.802,0.396 0.979,0.563 0.177,0.167 10 false *a 4.167,0.396 4.344,0.563 0.177,0.167 10 false *1 5.792,0.719 5.969,0.938 0.177,0.219 10 false *2
*1 No. 2 Engine Room Relay Block *2 INV Fuse
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A14-30 (+B), A14-31 (+B2) or 2 (INV fuse terminal) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Connect the inverter with converter assembly connector.


f.

Install the PCU fuse.

Result:
Proceed to
OK
NG




OK

20.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (INV)

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (INV)