Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9D-123  Hybrid Battery Temperature Sensor "A" Circuit Low  P0A9E-123  Hybrid Battery Temperature Sensor "A" Circuit High  P0AC7-123  Hybrid Battery Temperature Sensor "B" Circuit Low  P0AC8-123  Hybrid Battery Temperature Sensor "B" Circuit High  P0ACC-123  Hybrid Battery Temperature Sensor "C" Circuit Low  P0ACD-123  Hybrid Battery Temperature Sensor "C" Circuit High  


DESCRIPTION

Refer to the description for DTC P0A9C-123.

See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123

HINT:

After confirming that a DTC is output, use the intelligent tester to check "Temp of BATT TB 1 to 3" in the hybrid vehicle control system ECU data list.


Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or more GND short circuit

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9C-123

See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 1 to 3.

Powertrain > Hybrid Control > Data List
Tester Display
Temp of Batt TB1
Temp of Batt TB2
Temp of Batt TB3
50003 236 661,662,663
HINT:

Compare the temperature of the 3 battery temperature sensors to determine the sensor with the malfunction (Temp of Batt TB1 to TB3).


Result:
Proceed to
NEXT




NEXT

3.CHECK CONNECTOR CONNECTION CONDITION
3.CHECK CONNECTOR CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.
A260253E02
0.167,0.927 0.51,1.208 0.344,0.281 0.281,0.948 0.49,1.198 0.208,0.25 10 true z8

Check the connections of the z8 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

NG

CONNECT SECURELY

4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

OK

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR